Blastrac BMS-220LP-V2 Bedienungsanleitung

www.blastrac.com 1-800-256-3440

OPERATING MANUAL BMS-220LP-V2

VERSION 1.1

Table of Contents

1. Introduction........................................................................................................................................3

2. Machine Description .............................................................................................................................3

3. Safety................................................................................................................................................4

Safety Precautions .............................................................................................................................4

Safety Regulations .............................................................................................................................4

Safety Instructions..........................................................................................................................5-7

4. Initial Operation ..................................................................................................................................8

Checkpoints of Gas Cylinder Safety.......................................................................................................8

Checkpoints of Machine Safety.............................................................................................................8

5. Operation ...........................................................................................................................................9

Driving the Machine .........................................................................................................................10

Controlling Tool Position Cylinder .......................................................................................................11

6. Maintenance ................................................................................................................................ 12-13

Hydraulic System Instruction ........................................................................................................ 14-15

7. Cutting Head & Blades................................................................................................................... 16-18

8. Blade Application .......................................................................................................................... 19-23

9. Ditching ...................................................................................................................................... 24-25

10. Technical Data................................................................................................................................. 26

11. Contact ..........................................................................................................................................27

1. Introduction

It is important that all persons who are working or maintaining this machine read the manual carefully and

understand it fully. Keep this manual near to the machine, so it can always be consulted.

Only authorized and trained personnel may operate this machine.

2. Machine Description

The Blastrac BMS-220LP ride-on scraper is ideally suited for medium and large sized applications with the added

benefit of being gas operated for increased versatility. It is very maneuverable with zero turn radius, non-mark

tires and complete hydraulic control.

Main advantages of the BMS-220LP:

-Fast and easy removal of all types of flooring material

-Very compact, goes through standard doors & elevators

-Zero turn radius, ergonomic design for safe maneuvering, non–marking tires

-Very versatile, total freedom of movement, no electric cable.

-Complete hydraulic control (drive and tool control)

-Powered by a heavy duty motor delivering strong power with no worries of charging.

-Very high output compared to manual material removal.

Update image to new 220LP?

1 Left Wheel Drive Lever 6 Tool Holder

2 Tool Lift/Lower Lever 7 Propane Tank (Liquid Propane Type)

3 Ignition 8 Engine Cover

4 Tachometer/Hour Meter 9 Right Wheel Drive Lever

5 Throttle

3. Safety

It is important that all persons who are working with or maintaining this machine must read the manual carefully

and understand it fully.

Always keep this manual with the machine, so it can be referenced to at any time.

Safety Precautions

Make sure that persons who are not operating the machine are not in the surrounding area of the

machine.

Make sure that there is nothing standing or situated on the surface to be treated

Make sure that there are no cables or hoses in the driving direction of the machine.

Always drive backwards when driving up to a ramp or grade, and forwards when driving down the ramp.

Do not consume drugs or alcohol prior to or during the use of this machine.

Safety Regulations

Never change anything from the safety devices on the machine!

Persons who are not operating the machine must not be permitted to stay within 20 feet of the machine.

Always call a skilled electrician or your distributor when you have questions about the safety of the

electrical components.

Work on electrical equipment or operating materials may only be undertaken by a skilled electrician or by

trained persons under the guidance and supervision of a skilled electrician as well as in accordance with

the electrical engineering regulations.

The following sticker is placed on the machine.

Meanings of these symbols are:

Ear protection is required

Safety glasses with lateral

protection are required

CE-mark on this machine

Safety shoes required

Consult the manual before

operating the machine

Personnel must tie back long hair and not wear loose clothing or jewellery including rings.

Wear gloves and dust mask during operation of the machine.

Safety Instructions

Turn key to OFF when machine is parked.

oPark the machine always on a flat horizontal and levelled surface.

oCover the sharp blade or remove it when the machine is off.

Make sure the machine is clean and that the footrests are dry and free of grease and oil.

NEVER lift the machine with the mounted tool for maintenance! This sharp tool can be very dangerous!

The weight of the BMS-220LP is 2000 pounds. Only use an appropriately sized lift or crane to move/hoist

the BMS-220LP. The lift points are as shown below.

Chock wheels for transport and keep control handles in neutral position.

Don’t leave the machine unsecured on jobsites.

Machine can be lifted by a forklift. For this use prepared bracket (1) on bottom of machine:

Be aware of your surroundings and machine operating level. Do not run across hill, do not run on steep

incline, this could cause machine to tip over.

Always drive backwards when driving up to a ramp or grade, and forwards when driving down the ramp.

Do not run the machine in unsafe environments.

DANGER: Engine exhaust gases contain poisonous carbon monoxide. Carbon monoxide

is odorless and colorless and can cause injury or death if inhaled. Do not use equipment

indoors without adequate ventilation. Refer to OSHA guidelines and regulations

concerning maximum levels of exposure to carbon monoxide gases and other hazards

associated with using internal combustion engines. It is highly recommended that a CO

(carbon monoxide) detector be used to warn the user if levels become unsafe.

Warning: Engine, exhaust system and hydraulic component temperatures could be in

excess of 200°F causing severe burns if touched.

Engine Safety

4. Initial Operation

Before using the machine it is essential to inspect the machine every day.

It is not permitted to use the machine if it does not pass all of the checkpoints below.

Checkpoints of Gas Cylinder Safety:

Check the bottle for any damage before use.

Ensure hose to gas cylinder is fully seated and sealed before turning on the bottle.

Always turn the bottle completely on before starting the engine.

Always turn the bottle completely off after using the machine.

Checkpoints of Machine Safety:

Control levers should be in neutral position.

All hydraulic hose connections are tightened and there is no leakage of oil.

The safety functions and operating functions work correct.

There are not any loose nuts or bolts.

5. Operation

During the operation of the BMS-220LP, the following additional safety instructions must be followed closely.

Switching on the Machine:

Turn the valve on the propane tank CCW until it stops.

Take place on the seat (2) and put feet on the footrests. Operating the machine without being seated is

not possible because of the safety switch of the seat.

Turn the key contact switch (1) to the right.

Driving the Machine

The wheels of the machine are controlled by the two outside handles (1 and 3). Pushing both handles forwards,

the machine drives forwards. Pulling both handles backwards, the machine drives backwards. The driving speed

depends on the position of the handles. Pushing the right handle forwards the machine turns to the left. Pushing

one handle forwards and pulling another handle backwards the machine will turns around its axis. Correcting

direction while moving is accomplished by slightly reducing pressure on one handle or the other while moving.

1) Left wheel control handle.

2) Tool positioning control handle.

3) Right wheel control handle.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Blastrac Bodenreinigungsmaschine Handbücher

Blastrac

Blastrac BMG-555PRO Bedienungsanleitung

Blastrac

Blastrac BMG-780PRO Bedienungsanleitung

Blastrac

Blastrac BMS-220 ADB Bedienungsanleitung

Blastrac

Blastrac BGS-250 Bedienungsanleitung

Blastrac

Blastrac BG-250A Bedienungsanleitung

Blastrac

Blastrac BMG-435 Bedienungsanleitung

Blastrac

Blastrac BMS-280 Bedienungsanleitung

Blastrac

Blastrac 1-8DEZMKII Bedienungsanleitung

Blastrac

Blastrac BG-250E Bedienungsanleitung

Blastrac

Blastrac BMS-280LP Bedienungsanleitung

Blastrac

Blastrac BMG-580PRO Bedienungsanleitung

Blastrac

Blastrac BMG-555 Bedienungsanleitung

Blastrac

Blastrac BMG-435WD Bedienungsanleitung

Blastrac

Blastrac BG-250G13-S Bedienungsanleitung

Blastrac

Blastrac BG-250RS Bedienungsanleitung

Blastrac

Blastrac BG-250E Bedienungsanleitung

Blastrac

Blastrac BG-180EC Bedienungsanleitung

Blastrac

Blastrac BG-250E Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch