Blastrac BMS-H2750 Bedienungsanleitung
MODEL
BMS-H2750
Floor Scraping System
HIGH VOLUME RIDE-ON SCRAPER
Trust the Original Surface Preparation Experts
800.256.3440
blastrac.com
1
TABLE OF CONTENTS
BMS-H2750
HURRICANE
SECTION I GENERAL DESCRIPTION
SECTION II SPECIFICATIONS
SECTION III SAFETY AND PRECAUTIONS
SECTION IV INSTRUMENTS AND CONTROLS
SECTION V START-UP AND BREAK-IN
SECTION VI MACHINE OPERATION
SECTION VII PREVENTIVE MAINTAINANCE
SECTION VIII ENGINE
SECTION IX FRAME & COWLINGS
SECTION X HYD AND DRIVE COMPONENTS
SECTION XI VALVE JOYSTICK ASSEMBLY AND CABLES
SECTION XII STEERING JOYSTICK AND CABLES
2
OPERATIONS
AND
MAINTENANCE MANUAL
CUSTOMER
SERIAL NUMBER
DATE SHIPPED
3
SECTION I
GENERAL DESCRIPTION
BMS-H2750
The BMS-H2750 is operated by a propane-powered engine, driving a
tandem hydrostatic pump system, creating a (skid-steer) zero turn radius drive
train. Surface covering and coatings are removed by lowering a weighted blade
onto the surface and moving forward under a high torque drive system. The
surface coating is removed by a flexible sharpened blade conforming to the
floor surface, with the weight of the machine holding the blade firmly to the
floor. The weight does not allow the blade to lift or ride over well-adhered
surface coating material, thus lifting the off the floor coating.
After layers of carpet or laminates are removed the machine can be
connected to a grinder or slicer attachment to either clean up adhesives or
remove stubborn coatings.
4
SECTION II
SPECIFICATIONS
Weight 2750 lbs
Removable weight 1000 lbs
Height with Propane Tank 58 inches
Width 25 inches
Length with blade 51 inches
Length without blade 41 inches
Engine 25 Hp Kohler
Max Ground Speed 440 ft per min.
Torque per Wheel 1000 ft. lbs.
Fuel capacity 20 lb liquid propane
Hydraulic fluid capacity 4 gallons
5
SAFETY WARNING
CARBON MONOXIDE can cause
severe nausea, fainting or death.
Do not operate engine in closed or
confined area without proper
ventilation.
6
SECTION III
SAFETY AND PRECAUTIONS
Before operating the BMS-H2750 please read the entire operation and safety manual with
complete understanding of the safety section. If you have any questions on safety and precautions
please call 1-800-256-3440.
There are several advantages to an effective safety program which include: lower operating costs,
lower workman compensations, less work time lost, high employee morale, and less problems. No
one can work safely without knowing what precautions to take to insure personal safety.
Operators must know what equipment to wear, which job practices are safe and which are not, and
must be aware of what hazards are possible in the work area. A regular schedule of Preventive
Maintenance on your equipment is the best protection against unpleasant surprises that slow
production and sometimes result in injuries. Here are a few suggested safety tips.
1. The first step before any maintenance or inspection takes place should be to stop
the engine and disconnect the battery terminals.
2. Wear proper eye and ear protection and heavy duty work gloves at all times.
3. Practice good Preventive Maintenance.
4. Practice good housekeeping.
5. Allow the BMS-H2750 to come to a complete stop, turn off engine, and chock rear
wheels before performing any maintenance procedures.
6. Replace worn parts when necessary.
7. Do not reach into blade or control arm areas while machine is in operation.
8. Do not attempt to open any access door until the machine has come to a complete stop and
the engine and propane is turned off.
9. Be sure all electrical inspections or changes are done by a qualified electrician.
10. Loose surface coating can cause dangerous footing. Always be alert and careful.
11. After replacing parts be sure all tools used are removed from the machine. Be sure all bolts
and nuts are tightened. The loose connection of a rotating part could cause the part to fly
off with explosive force, causing serious damage to the equipment and possible injury to
the operator.
12. Always lower blade to the ground when the machine is unoccupied by the operator.
Serious bodily injury may result if arms are not in the lowered position when not occupied.
13. Never allow unauthorized personnel or the general public into the work area.
14. The work area should be barricaded off to adequately keep all untrained persons out of the
work site. If an unauthorized person enters the work area, stop the machine immediately
and do not restart the machinery until they have left the work area.
15. Always allow a 200-foot buffer safety zone around all surface preparation activity.
16. Always run the BMS-H2750 in a well-ventilated area, with an approved OSHA air-
monitoring system in place at all times.
17. Read and obey all safety labels placed on the machinery at all times. If safety labels have
been destroyed or removed call 1-800-256-3440 for replacement labels prior to operating
the machinery.
7
18. The BMS-H2750 is not a toy. All operators must be over 18 years of age and must have
read and reviewed the safety and procedures manual before operating the machinery.
19. The BMS-H2750 is designed for surface preparation ONLY. It is not intended for towing,
pushing or any other procedure not described in this manual.
20. Propane systems should be checked and documented twice yearly by a certified propane
professional for leaks or damaged parts. If a propane leak is detected leave the machine
immediately and seek assistance from propane professional. Do not use or restart
machinery until it is determined safe.
21. Horseplay and or high speed cornering is not allowed with this machine and could cause
rollover resulting in injury or death.
22. No smoking or open flame is allowed while machinery is running or within 50 feet of the
machine.
23. Operator must be sober and not under the influence of drugs or medication and under full
control of all bodily senses while operating this or any machinery.
24. When transporting the BMS-H2750, it is recommended to use a low bed tilt trailer. This
procedure insures the wheels do not leave a stable surface.
25. All BMS-H2750 operators must receive safety training before performing any functions
with the machine. Blastrac offers a maintenance orientation. New owners and operators are
advised to call 1-800-256-3440 for an appointment.
8
SECTION IV
Instruments and Controls
View # 1
Top view of BMS-H2750 machine
View # 2
Left side view of BMS-H2750 machine
View #3
Right side view of BMS-H2750 machine
View #4
Front view of BMS-H2750 machine
9
View #1 Top View
Andere Blastrac Elektrowerkzeuge Handbücher
