5. INTRODUCTION TO THE DRIVE SYSTEM
This system consists of the following components:
xCadence- Sensor: Sensing your pedaling rate
xSmart Controller: Real time calculating and coordinating optimized power output.
xBMS: Battery with BMS (Battery Management System), providing electric power to the
system while balancing the power consumption and protecting the battery cells.
xBrushless DC Motor: Provide the power assist.
xSmart Cycling computer: Control and display terminal.
As soon as you start pedaling, the system will sense your cadence (pedaling rate) and traveling
velocity, and real-timely coordinate the electrical motor to provide the just right power assist that
match your riding conditions, making your riding much easier and comfortable.
Note: This is a schematic representation of a folding e-bike with various possible equipment options.
The options shown may vary.
6. BATTERY (CHARGING, MAINTENANCE AND RANGE)
The battery must be charged before it is used for the first time. Please use exclusively the original
charger designated by Blaupunkt for charging; otherwise it might damage the battery, and may even
lead to fire and other hazard. Warranty expires, if a charger other than the designated is used.
xCheck carefully whether the rated input voltage of the charger is consistent with the
voltage of the power grid.
xCharge the battery in a dry place and ensure adequate ventilation. Neither the battery nor
the charger may be covered during the charging process.
xConnect first the output plug of the charger (2) with the charging jack of the battery . Then
connect the input plug (1) of the charger to the AC power supply.
xDepending on the model, you can remove the battery and charge it separately.
xFully charge of an empty battery takes 2-8 hours, depending on charging state, when the
charge indicator light on the charger turns from red to green, the battery has been fully
charged.
xAfter charging, first pull out the AC power plug (1) and then pull out the plug connected
with the battery (2).
xDo not leave the battery connected to the charger permanently and / or unattended.
xOnly charge the battery in rooms with a smoke detector installed. Charge the battery
xThe use of inverters with a modified sine wave is not recommended and can lead to
malfunctions.
MAINTENANCE
xYou can get the best performance and life out of your battery by charging it regularly
before use, even if it is not fully discharged.
xCharge the battery at room temperature.
xUse the battery in the temperature range from 0 ° - 25 ° C.
xIf you store a completely discharged battery for a long time, this leads to a permanent loss
of function. Recharge an empty battery as soon as possible.
xIf the battery is stored for a longer period of time, store the battery with approx. 50-70%
charge and check regularly for any remaining charge. A defective battery due to failure to
charge does not constitute a warranty claim.
xEvery battery with Li-Ion technology is subject to an unstoppable chemical aging process,
this process also takes place without using or charging the battery. The capacity of the
battery decreases with age. Decreasing capacity is not a defect or reason for complaint.
xTo avoid pollution, follow the local regulations for the proper disposal of the battery.
23_06_2021 Anleitung-E-Bikes.indd 30 23.06.2021 10:11:09
5. INTRODUCTION TO THE DRIVE SYSTEM
This system consists of the following components:
Cadence- Sensor: Sensing your pedaling rate
Smart Controller: Real time calculating and coordinating optimized power output.
BMS: Battery with BMS (Battery Management System), providing electric power tothe
system while balancing the power consumption and protecting the battery cells.
Brushless DC Motor: Provide the power assist.
Smart Cycling computer: Control and display terminal.
As soon as you start pedaling, the system will sense your cadence (pedaling rate) and traveling
velocity, and real-timely coordinate the electrical motor to provide the just right power assist that
match your riding conditions, making your riding much easier and comfortable.
Note: This is a schematic representation ofa folding e-bike with various possible equipment options.
The options shown may vary.
5. INTRODUCTION TO THE DRIVE SYSTEM
This system consists of the following components:
Cadence- Sensor: Sensing your pedaling rate
Smart Controller: Real time calculating and coordinating optimized power output.
BMS: Battery with BMS (Battery Management System), providing electric power tothe
system while balancing the power consumption and protecting the battery cells.
Brushless DC Motor: Provide the power assist.
Smart Cycling computer: Control and display terminal.
As soon as you start pedaling, the system will sense your cadence (pedaling rate) and traveling
velocity, and real-timely coordinate the electrical motor to provide the just right power assist that
match your riding conditions, making your riding much easier and comfortable.
Note: This is a schematic representation ofa folding e-bike with various possible equipment options.
The options shown may vary.
