Blaupunkt TravelPilot RNS 149 Bedienungsanleitung

Radio/Navigation

TravelPilot

RNS 149

Installation instructions

Safety information

– Faulty installation or servicing of this

equipment may result in malfunc-

tions in the vehicle’s electronic sys-

tems.

– To prevent damage to your TravelPi-

lot, be sure to use the correct adapt-

er cable to connect the vehicle 8-pin

+/- ISO plug.

Observe the following safety information

while installing and connecting the

system:

– Disconnect the negative terminal of

the battery.

– In doing so, observe the safety infor-

mation provided by the vehicle man-

ufacturer.

– Make sure not to damage any vehi-

cle parts when you drill holes.

– The cross-section of the positive and

negative wiring must not be less than

1.5 mm2.

– Use wire bushings for sharp-edged

holes.

– The TravelPilot can be used in vehi-

cles with:

• 12 V battery power

• Negative pole on the chassis

Information on proper

functioning

To ensure that the TravelPilot functions

properly, it is essential that the system

be calibrated after it has been complete-

ly installed (see Operating instructions

/ Contents / Calibration).

The system determines the distance trav-

elledviaitsconnectiontothevehiclespeed-

ometer signal.If there is no speedometer

signal, it will be necessary to have a route

sensor mounted by an authorised custom-

er service centre.

In this case you will have to order a sen-

sor kit (route sensor, magnet strip,

bracket and plug) from your dealer.

Order-No.: 7 607 611 093

1. Power supply

1.1 Connection to the vehicle ISO

standard plug

To prevent electrical malfunctions in

vehicle ISO plugs, you have to use the

universal ISO adapter cable (Order-

No. 7 607 621 126) (see Fig. 1).

The following vehicles with ISO

standard connections can current-

ly be fitted with the universal ISO

adapter cable: Alfa Romeo, Citroen,

Fiat, Honda, Lancia, Mercedes, Peu-

geot, Porsche, Renault, Skoda.

Installation instructions

For other vehicles with vehicle ISO

plugs, use the vehicle-specific ISO

adapter cables, e.g. for Audi, Skoda,

VW with active antennas (Order-No.

7 607 621 129) (see Fig. 2).

1.2 Power connection to vehicle-

specific plugs

If the radio connection in your vehicle

was fitted with a 10A fuse at the facto-

ry (see operating instructions or the

fusebox in your car.), you will stillneed

the vehicle-specific adapter cable

(see Fig. 3).

2. Connecting the speakers

2.1 Connecting the speakers to the

ISO standard plug

In vehicles pre-equipped with pas-

sive speakers (with 4-ohm speakers)

you can adapt the ISO plug in the

vehicle. If necessary, the ISO cable

(Order-No.7607 647 093) can be used

forextra length (see Fig. 4). Order spe-

cial adapter cables from your dealer

forvehicles pre-equipped with active

speakers.

Installation instructions

3. Installing the antenna

Connect the antenna wiring to the en-

closed bracket(see Fig. 5).

3.1 Radio antenna

In pre-equipped vehicles (e.g.: VW,

Seat, Audi), the antenna gets its pow-

er supply via the antenna wire (see the

vehicle operating instructions). If you

want to replace the OEM radio with a

conventional radio, you will have to

order an antenna supply diplexer (Or-

der-No. 7 691 290 202) or the adapter

cable (Order-No. 7 607 621 129) from

your dealer. You will find information

on the installation and connection of

the antenna in the antenna installation

instructions. (see Fig. 5).

3.2 GPS antenna (satellite navigation)

You will find information on how to in-

stall the antenna in the enclosed an-

tenna installation instructions.

If the GPS antenna is installed inside

the vehicle, we cannot guarantee that

the system will function correctly.

4. Installing the TravelPilot

4.1 Setting the Gyro

Important: Before the TravelPilot is

inserted, the gyroscope must be put in

a horizontal position (see Fig. 8).

Important: Installation position of the

TravelPilot: right / left: min. 5˚/ max.

+5˚,fronttoback:min. -10˚/max.+30˚

The TravelPilot is installed in the

standard car radio compartment pro-

vided by the manufacturer (see Fig. 5 ).

For vehicles without a DIN compart-

ment, Blaupunkt offers vehicle-specif-

ic installation kits for 50/52 mm units

for the most popular vehicle models.

Please check the installation condi-

tions in your vehicle and use a vehi-

cle-specificinstallation kit if necessary.

4.2 Installing the bracket

The bracket included with this Travel-

Pilot allows you to install the system in

vehicles with a DIN car radio compart-

ment measuring 182 x 53 x165 mm

and an instrument panel which is 1 to

20 mm in the area where the fastener

tabs are located, (see Fig. 1). For the

installation, you have to push the

bracket into the compartment and de-

termine which fastener tabs you can

bend over with a screwdriver (see

Fig. 6).

Note: Bend over as many of the fas-

tener tabs as possible.

4.3 Installing the TravelPilot

Push all of the plugs into the sockets

until they lock into place. Now insert

the navigation system from the front

into the bracket. Apply gentle pressure

to both side edges and push it in until

the spring locks snap into position on

the right and left (you will hear a loud

click).

Important! When you push in the sys-

tem,make sure that you donotputany

pressure on the display, the knobs or

the keys!

4.4 Removing the TravelPilot

Insertthe handles into the correspond-

ing holes on the left and right side of

the front panel and push them in until

you hear a loud click (unlocking the

side spring locks). Use both handles

to carefully pull the TravelPilot out of

the compartment. Now you can pull

out the connection cables by applying

pressure on the side of the plug (see

Fig. 7).

Note: Once the handles have locked

into place, they cannot be removed

until you pull the TravelPilot out of the

compartment.

4.5 Connecting the back-up light

signal wire

The back-up light signal wire connects

thesystem to the vehicle back-up light.

Make sure that this connection is

charged with 12 volts when the vehi-

cle is reversing.

Important: We assume no liability for

faulty connections and their conse-

quences!

4.6 Connecting the speedometer

signal

Important : Only an authorised cus-

tomer service centre should make this

connection.

Thespeedometer signal wire connects

the system to the vehicle-specific

speedometer signal connection.

Important : We assume no liability for

faulty connections and their conse-

quences!

Installation instructions

5. Connection diagrams

Power connection to the

vehicle ISO standard plug ......... Fig.1/2

Power connection to

the vehicle-specific plug ............ Fig.3

Speaker connection

4 speakers (4 Ω/35 W) .............. Fig.4

Antenna connection ................... Fig.5

TravelPilot installation ............... Fig.6/6a

TravelPilot removal .................... Fig.7

Setting the gyroscope................ Fig.8

Connection assignments ........... Fig.9

Connecting the sensors.............Fig.10

7 607 621 126

Fig.1 *Tel.-Mute (active low)

RRRF LF LR

4 Ohm

Fig.4

Fig.3

7 607 621 129

Fig.2

Fig.5

Radio antenna

GPS antenna

Installation instructions

Fig.5 3.2.

Bracket

GPS antenna

+30°

–10°

Installation instructions

Fig.8

Fig.6

Fig.6a

Fig.7

+30°

–10°

90°

O.K.

+30°

–10°

90°

14710 13 16 19

36912 15 18

258

11 14 17 20

C-1 C-2 C-3

1 Gala/Tacho 1 Speaker out RR+

2 Tel.-Mute (active low) 2 Speaker out RR-

3 RFLS 3 Speaker out RF+

4 Permanent +12V 4 Speaker out RF-

5 Aut.antenna 5 Speaker out LF+

6 Illumination 6 Speaker out LF-

7 Ignition 7 Speaker out LR+

8 Ground 8 Speaker out LR-

C1 C2 C3

1 Line Out LR 7 — 13 CDC Data-IN

2 Line Out RR 8 — 14 CDC Data-OUT

3 Line Out GND 9 — 15 +12V Permanent

4 — 10 +12V switched voltage (max. 150mA) 16 +12V switch voltage (max. 300mA)

5 — 11 Remote Control-In 17 CDC Data-GND

6 +12V switch voltage 12 Remote Control-GND 18 CDC AF/AUX-GND

(max 150mA) 19 CDC AF/AUX- L

20 CDC AF/AUX- R

1 GND

2—

3—

4—

5—

6—

7 Sensor

8—

9 Sensor

10 —

Wheel sensor

CD changerRC 06

Installation instructions

Fig.9

AmplifierEqualizer

Relais

12V

Tel.-Mute (active low)

Speedometer signal

Back-up light signal

Installation instructions

8 604 390 045

Wheel sensor

(required for vehicles without

a speedometer signal only)

Control cable (Power Antenna +)

The control cable is the connected positive output for

auxiliary components e.g.: power antennas,

(maximum load < 150 mA).

Important! Do not connect the control cable to terminal 15

(Plus connected) or terminal 30 (continuous plus).

Ground

Do not connectthe groundwire (min.cross-section 1.5mm2)

to the negative terminal of the battery.

Lay the ground wire to a suitable ground (chassis screw,

chassis metal) and screw it down.

Continuous plus connection (terminal 30 battery + 12 V)

Lay the plus wire (cross-section min.1.5 mm2) to the bat-

tery (not directly along the wire harnesses). Connect the

fuse holder to protect the plus wire and connect it to the

positive terminal on the battery.

Illumination connection

Illumination connection for vehicles with variable instrument

lighting (plus regulated).

Plus connection (connected to the ignition)

This connection must be made via the ignition

(terminal 15, +12V).

Fig.10

This information is subject to change without notice!

terminal

15 +12V

Andere Handbücher für TravelPilot RNS 149

Inhaltsverzeichnis

Andere Blaupunkt Auto-Navigationssystem Handbücher

Blaupunkt

Blaupunkt DX-R52 Bedienungsanleitung

Blaupunkt

Blaupunkt RNS 149 US Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot Lucca 5.2 Bedienungsanleitung

Blaupunkt

Blaupunkt New York 800 Truck Bedienungsanleitung

Blaupunkt

Blaupunkt Punta Del Este 960 Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot RNS 149 Service-Handbuch

Blaupunkt

Blaupunkt TravelPilot RGS 05 Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot RGS 05 Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot RGS 08 Bedienungsanleitung

Blaupunkt

Blaupunkt SERIES 840 Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot DX-V Bedienungsanleitung

Blaupunkt

Blaupunkt BikePilot2 Bedienungsanleitung

Blaupunkt

Blaupunkt VELOCITY POWER CAPE TOWN 900 DSP Bedienungsanleitung

Blaupunkt

Blaupunkt PHILADELPHIA 855 Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot 700 Bedienungsanleitung

Blaupunkt

Blaupunkt MotoPilot 43 Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot 43 Bedienungsanleitung

Blaupunkt

Blaupunkt CAPE TOWN 945 Bedienungsanleitung

Blaupunkt

Blaupunkt TRAVELPILOT LUCCA 3.3 Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot 300 Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot 55 Active Bedienungsanleitung

Blaupunkt

Blaupunkt Philadelphia 835 Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot RGN 08 Kurzanleitung

Blaupunkt

Blaupunkt PHILADELPHIA 845 Bedienungsanleitung

Beliebte Auto-Navigationssystem Handbücher anderer Marken

Clarion

Clarion Navigation In-Car Entertainment Bedienungsanleitung

Rosen

Rosen DP-1001 Bedienungsanleitung

Alpine

Alpine INE-W970HD Bedienungsanleitung

Pioneer

Pioneer MZ360500EX Bedienungsanleitung

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... Bedienungsanleitung

AvMap

AvMap Geosat 2C Bedienungsanleitung

Eonon

Eonon GE01B Bedienungsanleitung

Pioneer

Pioneer AVIC-Z920DAB Bedienungsanleitung

Nextar

Nextar M3-MX - Automotive GPS Receiver Bedienungsanleitung

Furrion

Furrion NV2200 Bedienungsanleitung

Mio

Mio MOOV 200-Series Bedienungsanleitung

Prestigio

Prestigio GeoVision 5150 Bedienungsanleitung

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Konfigurationshandbuch

Garmin

Garmin StreetPilot c510 Bedienungsanleitung

Garmin

Garmin nüvi 2200 Bedienungsanleitung

Garmin

Garmin 2610/2650 Bedienungsanleitung

Mazda

Mazda 107006AN Bedienungsanleitung

Toyota

Toyota TNS600 Bedienungsanleitung