Blendtec Total Blender Leitfaden
www.blendtec.com
Owner’s Manual and User Guide
® Total Blender
TABLE OF CONTENTS
SECTION PAGE#
SECTION1: IMPORTANT SAFEGUARDS 4
SECTION2:UNPACKING 6
SECTION3: TOTAL BLENDER OVERVIEW 7
SECTION4: INSTALLATION 7
SECTION5: CARE AND CLEANING 9
SECTION6: OPERATIONAL OVERVIEW 10
SECTION7: TROUBLESHOOTING 11
SECTION8: WARRANTY 13
4
SECTION1
IMPORTANTINFORMATION
Read all instructions carefully before using your TOTAL BLENDER™
1.1SAFETYCERTIFICATION
The blender is certied by ETL (Report No. 3018204-4, 3018204-2 &
3018204-3). To comply with UL standard 982 4th ed. 11-29-2001, and
to CSA standard C22.2 No. 195-m 1987, Nov. 1990, R 1994
1.2TOTALBLENDERCERTIFICATION
TOTAL BLENDER and its accessories are certied by NSF Internation-
al (NSF), under the letter K (for K-TEC) in the NSF Ofcial Listing.
1.3AVOIDCONTACTWITHMOVINGPARTS
• Keep ngers, hands, hair and clothing away from all moving parts.
• Keep all utensils away from the drive socket and blender blades during
operation. Metal utensils will damage blades.
• NEVER put hands into blender jar or add substances by hand when the blender
is operating.
• NEVER place jar into drive socket if blender motor is operating.
• DO NOT rock the blender during operation.
These precautions will prevent personal injury and/or damage to the blender.
1.4NEVEROPERATETHEBLENDERIFITAPPEARSDAMAGED
If the blender malfunctions call your service agent rst. If it is dropped or damaged in
any way, return the blender to a Blendtec service agent immediately for examination,
repair, electrical or mechanical adjustment, or possible replacement.
1.5NEVEROPERATEBLENDERINLIQUID
To protect against the risk of electrical shock do not put the motor base in water or
other liquid. Do not use the blender outdoors where it is subject to precipitation.
1.6NEVERPUTNON-FOODITEMSINTOJAR
Metal utensils, rocks and glass are dangerous if placed in jar. Damage caused by
such foreign objects will void the warranty. Keep hands and utensils out of jar while
blending to reduce the risk of severe injury to persons or damage to the blender.
Utensils may only be used when the blender is not running.
1.7NEVEROPERATETHEBLENDERWITHOUTTHELIDINPLACE
5
www.blendtec.com
1.8NEVEROPERATETHEBLENDERUSINGATTACHMENTSNOTSOLDBY
BLENDTEC
The use of any unauthorized attachments may cause re, electric shock, and/or injury
and will void the warranty.
1.9CONTAINERMUSTBEPROPERLYINPLACEWHILEAPPLIANCEIS
OPERATING
1.10BLADESARESHARP!HANDLECAREFULLY!
1.11WHENBLENDINGHOTLIQUIDS,REMOVECENTERPIECEOFLID
1.12POWERCORDPRECAUTIONS
• NEVER operate with a damaged cord or plug. (If the supply cord is damaged it
must be replaced by the manufacturer, or authorized service agent to avoid a
hazard
• DO NOT permit the cord to hang over the edge of the work surface.
• NEVER use an extension cord with the unit.
• Unplug the blender motor when not in use; before changing blender locations; or
cleaning.
1.13NEVERATTEMPTTOREPAIRTHEPOWERUNIT
Never remove the blender motor cover. The blender motor does not contain self-
adjustable or serviceable parts. A qualied service agent must make all service
adjustments. Removing the cover or attempting to service the blender will void the
warranty.
1.14TURNTHEPOWERSWITCHOFFWHENNOTINUSE
The Power Switch (ON/OFF switch) is located on the back of the blender motor cover.
1.15AVOIDTOUCHINGTHEBLENDERDRIVESOCKETAFTER EXTENSIVE
USE.
The blender drive socket may become hot after numerous cycles.
1.16CLOSESUPERVISIONISNECESSARYWHENAPPLIANCEISUSEDBY
ORNEARCHILDREN.
1.17THETOTALBLENDERISINTENDEDFORHOMEUSEONLY!ANYUSE
OFTHETOTALBLENDERTMFORCOMMERCIALPURPOSESVOIDSALL
WARRANTIES.
SAVETHESEINSTRUCTIONS
6
SECTION2
SAVEALLPACKAGINGMATERIALSANDINSTRUCTIONSFORFUTUREUSE.
2.1UNPACKINGYOURBLENDER
You should have received the following items:
• TOTAL BLENDER™ motor base
• Blender jar with lid
• Recipe book
1. Remove blender motor, blender jar and lid from packaging.
2. Unwind the power cord.
3. Check for any packing material that may have blocked ventilation holes in
the blender motor.
4. Inspect all items to ensure no damage occurred in shipment.
5. If any damage has occurred contact your Blendtec service agent
immediately.
2.2RECORDINGYOURSERIALNUMBERANDDATEOFPURCHASE
Record your blender motor serial number and date of purchase in the space below.
You will need these when contacting Blendtec for service or questions.
Motor Serial #:
____________________________________________________
(Found on bottom of motor base)
Date of Purchase:
____________________________________________________
Purchased From
____________________________________________________
2.3REGISTRATIONOFYOURBLENDER
Register online at www.blendtec.com (select “Product Registration”
under the ‘Service’ button) or return the registration card to the address provided.
7
www.blendtec.com
SECTION3
TOTALBLENDEROVERVIEW
(Refer to Figures 1 and 2)
3.1BLENDERMOTOR
• Motor Cover: Houses the power unit in a durable, easy-to-clean
polycarbonate.
• Touch Pad: Consists of nine buttons that contain pre-programmed settings for
selective blender control which includes a pulse button, and two speed control
buttons.
• LCD Information Center: Will indicate status of unit as well as overload or over-
temperature conditions.
• Power Unit: This unit is located within the blender motor and contains the machin-
ery that runs the blender.
• Power Switch: Located on the back lower-right corner of the power unit.
3.2BLENDERJARASSEMBLY
The blender jar assembly consists of the blender jar, blade assembly, and lid.
• Jar: Made from a tough durable material to provide maximum efciency and clear
visibility of blender performance.
• Blade Assembly: Stainless steel designed to provide fast consistent blending.
SECTION4
INSTALLATION
We recommend that surge protection be placed between the receptacle and the
blender motor.
TOTALBLENDERINSTALLATION
1. Place blender on a at, clean and dry surface.
2. Make sure a plug outlet is available within four feet of the blender motor.
3. Ensure that the unit is turned off before plugging it into a separate 120-volt recep-
tacle.
4. Ensure that blender vents are unobstructed to allow proper cooling during use.
8
Figure2FrontView
Figure1SideView
Lid
Jar
Blade Assembly
Motor Base Cover
Power Switch
Power Cord
Blender Drive
Socket
Touch Pad
LCD Information
Center
9
www.blendtec.com
SECTION5
CAREANDCLEANING
5.1AFTERUSECLEANING
1. Add 1 cup of hot water and a drop of liquid dishwashing soap to the blender jar.
2. Place the lid tightly onto the jar. Place the blender jar on the blender base, and
with your hand placed on top of the lid; press the pulse button for 5 seconds.
3. Rinse with clear water until all soap is rinsed from jar and lid.
4. Clean the blender base by simply wiping the base and touchpad with a damp rag
and water.
5.2LONG-TERMSANITATION
1. For long-term sanitation, occasionally ll the blender jar half way with hot water.
2. Add one teaspoon of liquid chlorine bleach.
3. Stir for 10 seconds to mix water and bleach. Let mixture stand in blender jar for
ve minutes.
4. Empty water/bleach mixture and rinse the jar thoroughly to ensure that there is
no bleach mixture left in the jar. Turn jar RIGHT SIDE UP on dish rack until dry.
5.3CLEANINGTIPSANDCAUTIONS
• Do not use abrasives or stiff brushes to clean the blender base or jar as this will
dull or scratch the surface. Cosmetic damage is not covered by warranty.
• NEVER submerge the blender motor in water. Avoid submerging blender jars for
more than 5 minutes. Water penetration through the lower jar seals will reduce
the life of the jar. After cleaning, we recommend the blender jar be stored up-
right.
• BLENDER JAR IS DISHWASHER SAFE - TOP RACK ONLY! Extreme temperatures
damage the lower seal to the jar.
10
SECTION6
OPERATIONALOVERVIEW
6.1MAINPOINTSOFOPERATION
1. Turn on the main power switch located on the back of the blender motor in the
lower right corner.
2. Place the blender jar on the base, making sure the jar is secure. Attach the
blender lid. Hold the jar lid down with your hand if the jar is more than half full.
3. Press the desired touch pad button once. You may press any button on the lower
row to stop the cycle.
4. When cycle is complete, remove the blender jar and serve.
6.2AUTOMATICCYCLEOPERATION
The Blendtec Total Blender has blending cycles for ice cream, frozen yogurt, ice
crushing, milkshakes, soups, syrups, fondues, sauces, dips, dressings, batters, whole
juice, and smoothies. These cycles have variable speed settings that will change
during the course of the cycle. This allows the blender to draw the contents into the
blending vortex, which creates the desired texture. The blender will run its pre-pro-
grammed cycle and automatically shut off. If at any point you want to stop the blender
before it has completed its cycle press any lower row button.
Note: The speed buttons allow you to control the blender to operate up to 10 speed
settings. Simply press the speed up button and the motor will begin. Continue press-
ing the Speed Up key to increase the speed, or press the Speed Down key at any time
to decrease speed. Once you have reached the desired speed release the button.
Once you press a speed button, the blender will begin to run at the selected speed,
then shut off after 50 seconds. To stop the cycle before the 50 seconds, press any
button on the lower row.
Andere Handbücher für Total Blender
2
Inhaltsverzeichnis
Andere Blendtec Mixer Handbücher
Blendtec
Blendtec DESIGNER SERIES Leitfaden
Blendtec
Blendtec Classic Bedienungsanleitung
Blendtec
Blendtec Total Blender Leitfaden
Blendtec
Blendtec Stealth Bedienungsanleitung
Blendtec
Blendtec Q-SERIES Bedienungsanleitung
Blendtec
Blendtec CHEF Bedienungsanleitung
Blendtec
Blendtec Wildside Plus Designer Series Leitfaden
Blendtec
Blendtec Rapid Rinser Bedienungsanleitung
Blendtec
Blendtec Home Blender Leitfaden
Blendtec
Blendtec Go 41-503 Bedienungsanleitung
Blendtec
Blendtec EZ 600 Leitfaden
Blendtec
Blendtec DESIGNER SERIES Leitfaden
Blendtec
Blendtec ES3 Bedienungsanleitung
Blendtec
Blendtec Mix n Blend II Kurzanleitung
Blendtec
Blendtec Professional Series Bedienungsanleitung
Blendtec
Blendtec Classic Bedienungsanleitung
Blendtec
Blendtec CLASSIC SERIES Wildside+ Leitfaden
Blendtec
Blendtec Designer Series WildSide Bedienungsanleitung
Blendtec
Blendtec Signature Series Bedienungsanleitung
Blendtec
Blendtec Xpress Bedienungsanleitung
