Blizzard Lighting MiniSystem Bedienungsanleitung

Blizzard Lighting, LLC

http://www.blizzardpro.com

Waukesha, WI USA

Page 2

TABLE OF CONTENTS

1. Getting Started 3

What’s In The Box? 3

Getting It Out Of the Box 3

Powering Up! 3

Getting A Hold Of Us 3

Safety Instructions 4

General Requirements 4

Laser Safety Requirements 4

2. Meet the MiniSystem™ 5

Main Features 5

Dimensional Drawings 5

MiniSystem™ Pin-Up Picture 6

The Control Panel 6

3. Setup 7

Fuse Replacement 7

Mounting & Rigging 7

4. Operating Instructions 8

The Control Panel 8

Using the IR Remote Control 9

5. Appendix 10

Keeping Your MiniSystem™ As Good As New 10

Returns (Gasp!) 10

Shipping Issues 10

Tech Specs! 11

Page 3

1. GETTING STARTED

What’s In The Box?

• 1 x MiniSystem™ Fixture

• 1 x IR Remote Control

• 1 x IEC Power Cord

• 1 x Mounting Bracket & Locking Knobs

Getting It Out Of the Box

Congratulations on purchasing the 4-in-1 minisystem™ party light. Now that

you’ve got minisystem™, you should carefully unpack the box and check the

contents to ensure that all parts are present and in good condition. If anything

looks as if it has been damaged in transit, notify the shipper immediately and

keep the packing material for inspection. Again, please save the carton and all

packing materials. If a xture must be returned to the factory, it is important

that the xture be returned in the original factory box and packing.

Powering Up!

All xtures must be powered directly o a switched circuit and cannot be run

o a rheostat (variable resistor) or dimmer circuit, even if the rheostat

or dimmer channel is used solely for a 0% to 100% switch.

Warning! All xtures must be connected to circuits with a suitable

Ground (Earthing).

Getting A Hold Of Us

If something goes wrong, please visit www.blizzardpro.com/support

and open a support ticket. We’ll be happy to help, honest.

Disclaimer: The information and specications contained in this document are

subject to change without notice. Blizzard Lighting™ assumes no responsibility

or liability for any errors or omissions that may appear in this user manual.

Blizzard Lighting™ reserves the right to update the existing document or to

create a new document to correct any errors or omissions at any time. You can

download the latest version of this document from www.blizzardpro.com.

Author: Date: Last Edited: Date:

J. Thomas 9/24/2020 J. Thomas 12/28/2020

Page 4

Please read these instructions carefully. They include

important information about the installation, usage and

maintenance of this product.

Safety Instructions

General Requirements

• Always make sure that you are connecting to the proper voltage.

• This product is intended for indoor use only.

• To prevent risk of re or shock, do not expose xture to rain or moisture.

• The unit must be installed in a location with adequate ventilation.

• Always disconnect from the power source before servicing or replacing fuse.

• Never try to repair the unit by yourself.

• Never connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on it.

Laser Safety Requirements

Lasers are one of the coolest eects available, and when they are used appro-

priately, they will be fun, legal and harmless. To make sure that is the case:

• Always set up and install all laser eects so that all laser light is at least 3

meters (9.8 feet) above the oor on which people can stand.

• After setting up, and before public use, test laser to ensure proper function.

Do not use if any defect is detected. Do not use if laser emits only one or two

laser beams rather than dozens/hundreds, as this could indicate damage to the

diraction grating optic, and could allow emission of higher laser levels above

Class 3R.

• Never point lasers at people, or look into the laser aperture/beams.

• Never point a laser at aircraft, this is a federal oense!

• Never point un-terminated laser beams into the sky.

• Never expose the output optic (aperture) to cleaning chemicals.

• Never use laser if the laser appears to emit only one or two beams.

• Never use the laser if the housing is damaged, the housing is open, or if the

optics appear damaged in any way.

• Never open the laser housing. The high laser power levels inside of the protec-

tive housing can start res, burn skin and will cause instant eye injury.

• Never leave this device running unattended.

The operation of a class 3R laser show is only allowed if the show is controlled

by a skilled and well-trained operator, familiar with the data from this manual.

The legal requirements for using laser entertainment products vary from country

to country. The user is responsible for the legal requirements at the location/

country of use.

Page 5

2. MEET THE MINISYSTEM™

Main Features

• Room lling R/G/B/W beams via rotating crystal half-sphere

• Wash, strobe, and chase RGB LED eye-candy eects

• Projects thousands of slow/fast moving red and green laser dots

• Laser safety key lock switch

• 2-button manual control (no DMX)

• Easy-to-use IR remote control

• Built-in microphone with sensitivity adjustments

• Multiple built-in auto and sound active show eects

• Energy ecient, low power consumption

• Lightweight and compact

• IEC power input

• Black metal housing with mounting bracket & locking knobs

• Operating modes: auto mode, sound active

Dimensional Drawings

9.8" (248 mm)

6.3" (160 mm)

9.8" (248 mm)

7.9" (200 mm)

Page 6

The Control Panel

MiniSystem™ Pin-Up Picture

Rotating Crystal Half-

Sphere with 4* 3W LEDs

Mounting

Bracket

Safety

Loop

100mW, 650nm Red + 30mW,

520nm Green Laser

32* 3-in-1 RGB SMD5050

Wash/Strobe/Chase

Locking

Knob

Locking

Knob

Power Switch

Internal Mic

Mic Sensitivity Sound Active

Mode

Selector

Laser Safety

Key Switch

LED

Indicator

Turn ON to

Operate Laser

Page 7

Fuse Replacement

1. With a at head screwdriver, remove the fuse holder from its housing.

2. Carefully remove the damaged fuse from the holder and replace with exact

same type of fuse (2A, 250V).

Before replacing a fuse, disconnect the power cord.

ALWAYS replace with the same type and rating of fuse.

3. SETUP

Mounting & Rigging

This xture may be mounted in any SAFE position provided there is enough

room for ventilation. The fan or vent pathway must never be obstructed.

IMPORTANT: Regardless of the rigging option

you choose for your xtures, always be sure to

secure your xture with a safety cable.

Mount the xture using a suitable "C" or "O"

type clamp. The clamps should be rated to

hold at least 10x the xture’s weight to ensure

structural stability.

Do not mount to surfaces of unknown

strength, and ensure properly rated rigging is

used when mounting xtures overhead.

Overhead mounting requires extensive

experience, which includes calculating working

load limits, knowledge of the installation

material being used, and periodic safety

inspections.

If you lack these qualications, do not attempt the installation yourself.

Improper installation can result in bodily injury.

Page 8

1 ON/OFF Power switch

2 MIC Internal microphone

3 VOL Using a small phillips screwdriver, adjust clockwise for

high mic sensitivity, or adjust counter-clockwise for low

sensitivity.

4 MODE

(button)

Show 0: LED, Laser, and Strobe shows (random 1-3)

Show 1: LED show

Show 2: Strobe show

Show 3: Laser show

5 SOUND

ON/OFF

(button)

Switches between the following 3 options with each button

press: Fast, Slow, and Sound Active.

Fast: Cycles through show modes 0-3, fast. The LED

indicator ashes fast when active.

Slow: Cycles through show modes 0-3, slow. The LED

indicator ashes slowly when active.

Sound Active: Cycles through show modes 0-3, controlled

by sound. The LED indicator ashes with beat.

4. OPERATING INSTRUCTIONS

The Control Panel

All the features and dierent modes possible with the minisystem™ can be

accessed by using the control panel buttons or IR remote control. The buttons

allow you to control the unit, as detailed below.

Note: You must turn the laser safety key switch to "ON" to use the lasers.

Page 9

Puts the xture in standby mode. Press again to

return to normal working mode.

This button shows all 3 built-in show programs in

random order (Shows 1-3).

Press the "Show 1" button for the LED show.

Press the "Show 2" button for the Strobe show.

Press the "Show 3" button for the Laser show.

Remember to make sure that the laser safety key

switch is turned "ON".

Cycles through all of the show modes 0-3, fast. While running, the LED

indicator will ash fast.

Cycles through all of the show modes 0-3, slow. While running, the LED

indicator will ash slow.

Cycles through all of the show modes 0-3, controlled by sound. The LED

indicator will ash with beat.

Using the IR Remote Control

All the goodies and dierent modes possible with the minisystem™ can be

accessed by using the IR remote control.

The IR remote control is simple to use. It oers the same functionality of the

LED control panel, with the addition of quick access shortcut buttons.

Page 10

Keeping Your MiniSystem™ As Good As New

The xture you’ve received is a rugged, tough piece of pro lighting equipment,

and as long as you take care of it, it will take care of you. That said, you’ll need

to take care of it if you want it to operate as designed. You should keep the

xture clean, especially if you are using it in an environment with a lot of dust,

fog, haze, wild animals, wild teenagers or spilled drinks.

Cleaning the optics routinely with a suitable glass cleaner will greatly improve

the quality of light output. Keeping the fans free of dust and debris will keep

the xture running cool and prevent damage from overheating.

In transit, keep the xtures in cases. You wouldn’t throw a prized guitar,

drumset, or other piece of expensive gear into a gear trailer without a case,

and similarly, you shouldn’t even think about doing it with your shiny new light

xtures.

Common sense and taking care of your xtures will be the single biggest thing

you can do to keep them running at peak performance and let you worry about

designing a great light show, putting on a great concert, or maximizing your

client’s satisfaction and “wow factor.” That’s what it’s all about, after all!

Returns (Gasp!)

We’ve taken a lot of precautions to make sure you never even have to worry

about sending a defective unit back, or sending a unit in for service. But,

like any complex piece of equipment designed and built by humans, once in a

while, something doesn’t go as planned. If you nd yourself with a xture that

isn’t behaving like a good little xture should, you’ll need to obtain a Return

Authorization (RA).

Don’t worry, this is easy. Just visit www.blizzardpro.com/support and open a

support ticket, and we’ll issue you an RA. Then, you’ll need to send the unit to

us using a trackable, pre-paid freight method. We suggest using USPS Priority

or UPS. Make sure you carefully pack the xture for transit, and whenever

possible, use the original box & packing for shipping.

When returning your xture for service, be sure to include the following:

1.) Your contact information (Name, Address, Phone Number, Email address).

2.) The RA# issued to you

3.) A brief description of the problem/symptoms.

We will, at our discretion, repair or replace the xture. Please remember

that any shipping damage which occurs in transit to us is the customer’s

responsibility, so pack it well!

Shipping Issues

Damage incurred in shipping is the responsibility of the shipper, and

must be reported to the carrier immediately upon receipt of the items.

Claims must be made within seven (7) days of receipt.

5. APPENDIX

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Blizzard Lighting DJ-Equipment Handbücher

Blizzard Lighting

Blizzard Lighting PROPAR COB RGBAW Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Solar Ray Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting weather system Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Torrent FZ Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting N-Trance Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting LOOK Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Tour QT Skywire Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting LOOP Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting LB Bar CSI Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting G-Max 200 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Weather System EXA Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Kaptivator Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Blockhead Z9 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting TOURNADO CSI COB Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ToughSTICK RGBAW Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting StormChaser Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Cyc Out Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Super-G 150 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting VERISMO RGBALC Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Motif Fresco Series Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting STILETTO I7 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting OBERON PROFILE NZ Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Flurry Z Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ENIGMA M4 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung