Blizzard Lighting G70 Bedienungsanleitung

Blizzard Lighting, LLC

www.blizzardlighting.com

Waukesha, WI USA

Page 2

TABLE OF CONTENTS

G70™ LED Moving Head Spot 1

1. Getting Started 3

What’s In The Box? 3

Getting It Out Of The Box 3

Powering Up! 3

Getting A Hold Of Us 3

Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet The G70™ Spot 5

Features 5

DMX Quick Reference 5

The G70 Pin-up Picture 6

3. Setup 7

Fuse Replacement 7

Connecting A Bunch Of G70’s 7

Data/DMX Cables 7

Cable Connectors 8

3-Pin??? 5-Pin??? Huh? 8

Take It To The Next Level: Setting up DMX Control 8

Fixture Linking (Master/Slave Mode) 9

Mounting/Rigging 9

Mounting Points 10

Clamp Mounting 11

 Securingthexture     11

4. Operating Adjustments 12

The Control Panel 12

Control Panel Menu Structure 13

Channel Mode Selection 13

Language Selection 13

System Reset 13

Manual Adjustments 13

DMX, Auto & Sound Active Modes 13

Invert the Pan and Tilt 13

Flip the LCD Display 13

DMX Channel Values In-Depth 14

Gobo Replacement 15

Troubleshooting 16

5. Appendix 17

A Quick DMX Lesson 17

Keeping Your G70 Spot As Good As New 18

Returns (Gasp!) 18

Shipping Issues 18

Tech Specs 19

Page 3

1. GETTING STARTED

What’s In The Box?

• 1 x G70™ Moving Head Spot

• An Ever-So-Handy Power Cord

• A Sweet Safety Cable & set of Mounting Brackets

• One really classy DMX cable

• This Lovely User Manual

Getting It Out Of The Box

Congratulations on your purchase of the amazing G70™ LED moving spot head. With

a name like G70™, its gotta be good! Now that you’ve got your G70™ (or hopefully,

G70’s!)

, you should carefully unpack the box and check the contents to ensure that all

parts are present and in good condition. If anything looks as if it has been damaged in

transit, notify the shipper immediately and keep the packing material for inspection.

Again,pleasesavethecartonandallpackingmaterials.Ifaxturemustbereturned

tothefactory,itisimportantthatthexturebereturnedintheoriginalfactoryboxand

packing.

Powering Up!

Allxturesmustbepowereddirectlyoffaswitchedcircuitandcannot be run off a

rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer

channel is used solely for a 0% to 100% switch.

AC Voltage Switch -Notallxtureshaveavoltageselectswitch,sopleaseverifythatthe

xtureyoureceiveissuitableforyourlocalpowersupply.Seethelabelonthextureor

refertothexture’sspecicationschartformoreinformation.Axture’slistedcurrent

ratingisitsaveragecurrentdrawundernormalconditions.Checkthextureordevice

carefully to make sure that if a voltage selection switch exists that it is set to the correct

line voltage you will use.

Warning! Verify that the voltage select switch on your unit matches the line

voltage applied. Damage to your xture may result if the line voltage applied

does not match the voltage indicated on the voltage selector switch. All xtures

must be connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, please just visit our website at www.blizzardlighting.

com and open a support ticket. We’ll be happy to help, honest.

Blizzard Lighting

N16 W23390 Stoneridge Dr. Ste E

Waukesha, WI 53188 USA

www.blizzardlighting.com

414-395-8365

Disclaimer:Theinformationandspecicationscontainedinthisdocumentaresubject

to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any

errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the

right to update the existing document or to create a new document to correct any errors

or omissions at any time. You can download the latest version of this document from

www.blizzardlighting.com.

Author: Date: Last Edited: Date:

J. Thomas 7/12/2014 J. Thomas 7/24/2014

Page 4

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone

else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that

the line voltage you are connecting to is not higher than that stated on the de-

calorrearpanelofthexture.

• This product is intended for indoor use only.

•Topreventriskofreorshock,donotexposexturetorainormoisture.

•Makesuretherearenoammablematerialsclosetotheunitwhileoperating.

• The unit must be installed in a location with adequate ventilation, at least

20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse

and be sure to replace with same fuse size and type.

•ALWAYSsecurextureusingasafetychain.NEVERcarrythexturebyits

head. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately.

NEVER try to repair the unit by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized tech-

nical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not

open the housing or attempt any repairs yourself. In the unlikely event

your unit may require service, please open a support ticket at www.

blizzardlighting.com/tickets.

Page 5

2. MEET THE G70™MOVING HEAD SPOT

MAIN FEATURES

• Compact Intelligent Moving Head Fixture

• 70W (7* 10W) CREE® LED Source

• 7 Dichroic Colors (including UV) + White

• 11/14-Channel DMX Control Modes

• Pan: 540º/ Tilt: 270º (8-16 Bit Resolution)

• Dual Gobo Wheels

• Static Gobos: 7 Metal + Open

• Rotating Gobos: 2 Glass, 4 Metal + Open

• Rotating 3-Facet Prism

• Variable Electronic Dimmer (0 – 100%)

• Electronic Focus

• Gobo-Flow, Rainbow-Flow + Shake w/Bi-Directional Rotation

• Multiple Built-In Auto & Sound Activated Programs

• Cooling System: Forced Convection Cooling

• Housing: Flame-Retardant Plastic (V0)

• DMX-512, Auto, Sound Active, & Master-Slave

CONTROL:

• USITT DMX-512 (11/14 Channels)

• 3-pin Input/Output

• 4-button menu with LCD icon-based display

DMX Quick Reference (11/14-Channel Modes)

Channel Reduced Mode Channel Standard Mode

1Pan 1Pan

2 Tilt 2 Fine Pan

3 Color Wheel 3 Tilt

4 Gobo Wheel 1 4 Fine Tilt

5 Gobo Wheel 2 5 Pan/Tilt Speed

6 Gobo 2 Rotation 6 Color Wheel

7 Prism + Rotation 7 Gobo Wheel 1

8 Focus 8 Gobo Wheel 2

9 Dimmer 9 Gobo 2 Rotation

10 Strobe 10 Prism + Rotation

11 Built-in Programs 11 Focus

-- -- 12 Dimmer

-- -- 13 Strobe

-- -- 14 Built-in Programs

Page 6

Figure 1: The G70™ Pin-Up Picture

Lens

Buttons

LCD Readout

Figure 2: The Rear Connections

DMX OutPower Switch

Power In

Power Out

Head/Arms

Carry Handle

DMX InFuse Cover

Page 7

3. SETUP

Fuse Replacement

Withaatheadscrewdriver,wedgethe

fuse holder out of its housing. Remove the

damaged fuse from its holder and replace

with exact same type fuse. Insert the fuse

holder back in its place and reconnect

power.

Connecting A Bunch of G70 Fixtures™

You will need a serial data link to run light shows using a DMX-512

controllerortorunshowsontwoormorexturessettosyncinmas-

ter/slave operating mode. The combined number of channels required

byallthexturesonaserialdatalinkdeterminesthenumberofx-

tures the data link can support.

Fixtures on a serial data link must be daisy chained in one single line.

Also,connectingmorethan32xturesononeserialdatalinkwithout

the use of a DMX optically-isolated splitter may result in deterioration

of the digital DMX signal.

The maximum recommended cable-run distance is 500 meters (1640

ft).Themaximumrecommendednumberofxturesonaserialdata

linkis32xtures.

Data/DMX Cabling

Tolinkxturestogetheryou’llneeddatacables.Youshouldusedata-

grade cables that can carry a high quality signal and are less prone to

electromagnetic interference.

Forinstance,Belden©9841meetsthespecicationsforEIARS-485

applications. Standard microphone cables will “probably” be OK, but

note that they cannot transmit DMX data as reliably over long distanc-

es. In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft.

Maximum capacitance between conductor & shield – 55 pF/ft.

Maximum resistance of 20 ohms / 1000 ft.

Nominal impedance 100 – 140 ohms

Page 8

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR

connector on the other end. (Duh!)

CAUTION:Donotallowcontactbetweenthecommonandthex-

ture’s chassis ground. Grounding the common can cause a ground

loop,andyourxturemayperformerratically.Testcableswithan

ohm meter to verify correct polarity and to make sure the pins are not

grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.

They are widely available over the internet and from specialty retailers If you’d like to build your own, the

chart below details a proper cable conversion:

Conductor 3-Pin Female

(Output)

5-Pin Male

(Input)

Ground/Shield Pin 1 Pin 1

DMX Data (-) Pin 2 Pin 2

DMX Data (+) Pin 3 Pin 3

Not Used. No Connection. No Connection.

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the

DMX cable to the female connector (output)

on the controller.

Step 2: Connect the female connector of the

DMXcabletotherstxture’smaleconnec-

tor (input). Note: It doesn’t matter which

xtureaddressistherstoneconnected.

Werecommendconnectingthexturesin

terms of their proximity to the controller,

ratherthanconnectingthelowestxture

numberrst,andsoon.

Step 3:Connectotherxturesinthechain

from output to input as above. Place a DMX

terminatorontheoutputofthenalxture

to ensure best communication.

Page 9

Fixture Linking (Master/Slave Mode)

1. Connect the (male) 3 pin connector side of the

DMX cable to the output (female) 3 pin connector of

therstxture.

2. Connect the end of the cable coming from the

rstxturewhichwillhavea(female)3pinconnec-

tortotheinputconnectorofthenextxturecon-

sisting of a (male) 3 pin connector. Then, proceed

to connect from the output as stated above to the

inputofthefollowingxtureandsoon.

A quick note: Often,

the setup for Master-

Slave and Standalone

operation requires that

therstxtureinthe

chain be initialized for

this purpose via either

settings in the control

panel or DIP-switches.

Secondarily,thextures

that follow may also re-

quire a slave setting.

Check the “Operating Adjustments” section in this manual for com-

pleteinstructionsforthistypeofsetupandconguration.

Mounting & Rigging

ThisxturemaybemountedinanySAFEpositionprovidedthereis

enough room for ventilation.

It is important never to obstruct the fan or vents pathway. Mount the

xtureusingasuitable“C”or“O”typeclamp.Theclampshouldbe

ratedtoholdatleast10xthexture’sweighttoensurestructuralsta-

bility. Do not mount to surfaces with unknown strength, and ensure

properly“rated”riggingisusedwhenmountingxturesoverhead.

Adjusttheangleofthexturebylooseningbothknobsandtiltingthe

xture.Afterndingthedesiredposition,retightenbothknobs.

• When selecting installation location, take into consideration lamp

replacement access (if applicable) and routine maintenance.

• Safety cables MUST ALWAYS be used.

•Nevermountinplaceswherethexturewillbeexposedtorain,

high humidity, extreme temperature changes or restricted ventilation.

Page 10

Mounting Points

Overhead mounting requires extensive experience, which includes

calculating working load limits, knowledge of the installation material

being used, and periodic safety inspection of all installation material

andthexture.Ifyoulackthesequalications,donotattemptthe

installation yourself. Improper installation can result in bodily injury.

Caution!

Pleasebeaware,youshouldhaveaqualiedelectricianperformingall

of your electrical connection needs. Better safe than sorry!

Be sure to complete all rigging and installation procedures before

connecting the main power cord to the appropriate wall outlet.

Inhaltsverzeichnis

Andere Blizzard Lighting Beleuchtungsausrüstung Handbücher

Blizzard Lighting

Blizzard Lighting KRYO.MIX CMY Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting THE PUCK RGBA LED PAR Can Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting infinipix cyclone Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ICE 30 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Switch Blade X3 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Lo-Pro CSI Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting The Puck 3NX Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Lo-Pro Flux Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Rocklite RGBAW Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting REANIMATOR Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Torrent F3 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Motif Risplendi 150 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ToughPar V12 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting the puck pro zoom Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck Pro Zoom EXA Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting COLORISE Infiniwhite Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Mezmerizor 4FX Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting HUSH PAR Infiniwhite 500 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Pocket Rocket Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Flurry Spot Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ToughPar V12 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ROCKER PANEL RGBAW Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting HotBox RGBW/RGBA Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ToughPAR Satellight Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung