Blue Star CFMR1000 Bedienungsanleitung

Installation Instructions

Remote Fans

CFMR1000 & CFMR1400

Inline Blowers

INLB300, INLB600 & INLB1200

PLEASE READ COMPLETE INSTRUCTIONS BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT: Save these instructions for the local electrical inspector’s use.

INSTALLER: Please leave these instructions with this unit for the owner.

OWNER: Please retain the instructions for future reference.

SAFETY WARNING: Turn power circuit OFF at the service panel and lock panel door before

wiring this unit.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION –To reduce the

risk of a rangetop grease fire.

1. Never leave cooktop surface

unattended while on high

setting

2. Boil overs cause smoke and

greasy spillovers may ignite.

Heat oils slowly on low or

medium settings.

3. Hood fan should always be

ON when cooking on high

heat or when flambeing

foods (i.e. Crepes Suzette,

Cherries Jubilee, Peppercorn

Beef Flambe.)

4. Clean in-hood fans

frequently. Do not allow

grease to accumulate on fan

or baffle filters.

5. Always use cookware

appropriate for the size of the

surface element.

CAUTION –To reduce the

risk of fire, electric shock, or

injury to people, observe the

following:

1. Use this rangehood only in

the manner intended by the

manufacturer. If you have

any questions, contact the

manufacturer –Prizer

Hoods.

2. Before servicing or cleaning

the unit, switch power off at

service panel and lock the

panel to prevent the power

from being switched on

accidentally. When switched

off for service, attach a tag to

the service panel to indicate

power has been switched off

for maintenance.

3. Install this rangehood only

with remote fan models rated

maximum 12.8A or in-hood

fans manufacturered by

Prizer Hoods, CFM300,

CFM600, CFM1200.

CAUTION –To reduce the

risk of injury to people, in the

event of a rangetop grease fire,

observe the following:

1. SMOTHER FLAMES with a

tight fitting lid, cookie sheet

or other metal tray.

Immediately turn the gas

burner OFF. NEVER USE

WATER, wet dish-cloths or

towels as a violent steam

explosion will occur.

2. PREVENT BURNS. If gas

flames do not extinguish

immediately: EVACUATE

AND CALL THE FIRE

DEPARTMENT.

3. NEVER PICK UP A

FLAMING PAN as you may

sustain burns.

4. Use fire extinguisher only if:

•You know you have a class

ABC extinguisher, and you

know how to operate it.

•Fire is small & contained in

the area where it started.

•Fire department is being

called.

•You can fight the fire with

your back to an exit.

CAUTION: FOR GENERAL VENTILATION

USE ONLY. DO NOT USE TO EXHAUST

HAZARDOUS OR EXPLOSIVE MATERIALS

OR VAPOR.

SAFETY PROCEDURES FOR INSTALLING YOUR

NEW PRIZER HOOD (continued)

CAUTION –To reduce the risk of fire, electricshock, or injury to people, observe the following:

CAUTION –For general ventilation use only. Do not use to exhaust hazardous or explosive materials

or vapors.

1. Installation work and electrical wiring must be done by a qualified installer in accordance with all

applicable codes and standards, including re-rated construction.

2. Sufficient air is needed for proper combustion and gas exhaustion through the flue to prevent

backdrafting. Follow the manufacturer’s guidelines and safety standards such as those published by the

National Fire Protection Association (NFPA), and the American Society of Heating, Refrigeration and

Air Conditioning Engineers (ASHRAE), and the local building code authorities.

3. When cutting/drilling into a wall or ceiling, avoid damage to electrical wiring and other hidden utilities.

4. In-hood or in-line fans must be vented to the outdoors.

5. If a ventilation unit is to be installed over a tub or shower, it must be marked as appropriate for the

application and be connected to a GFCI (Ground Fault Circuit Interrupter) –protected branch circuit.

6. NEVER place a control switch where it can be reached from a tub or shower.

7. CAUTION –To reduce the risk of fire within walls or roofs, use only metal ductwork.

8. Install this hood in accordance with all requirements specified by the manufacturer of your

cooktop/range.

9. Install this hood using required clearance from cooking surface to combustible material specified in

cooktop installation instructions.

READ & SAVE: UPON RECEIVING YOUR HOOD

•The high degree of craftsmanship in the construction

and finish of your hood requires careful handling to

ensure proper installation.

•Do not remove your hood from its carton until you are

ready to hang it.

•Do not store your hood anywhere other than within the

carton. If it is necessary to remove your hood from the

carton, place it on a blanket or padded area that will

protect your hood from scratches or indentations.

•Do not lift the hood by its utensil rail. Place your

fingers under the lower reveal of the hood. Grasp

firmly and lift.

•Wearing cotton gloves are preferred. They will protect

the surface from fine scratches and eliminate

fingerprints.

•Remove all rings, watches, belt buckles and jackets

(snaps/zippers) to prevent scratches on the hood.

•If applicable, do not remove the protective covering

from your hood until the installation process is

complete. It will be necessary to remove only a small

portion on the back side for a wall mounted hood in

order to position in place.

•Located within the hood cavity (behind the baffles) are

component parts and halogen bulbs.

MOUNTING OPTIONS FOR REMOTE FANS

MOUNTING REMOTE FANS ON ROOF OR OUTSIDE WALL

To prepare for mounting a remote fan, inspect the blower wheel to ensure it turns freely. Do not replace the

top unit to the remote fan until the installation has been completed. A remote fan cannot be installed in a

condition where the exhaust/discharge opening is less than 15” from the ground level. NOTE: There may be

some local codes that will not permit this kind of installation. Heavy snow will prevent the damper from

opening due to snow blockage. The installer must check all local codes for outdoor wall installation of the

remote fan.

1. Cut out a round hole to accommodate the size ducting you will be using. Cut a second hole for the

electrical conduit. (see Figure 5-C)

2. When installing a remote fan on a flat roof or a roof with a pitch less than 1 ½” in 12 inches, install the

remote fan in such a way that the discharge (the lowest portion of the curb) is directed away from any

prevailing winds.

3. When installing a remote fan on a roof or outside wall, direct the discharge (the lowest portion of the

curb) pointing down the slope as this is in accordance with the Standard Roofing Procedures: front

discharge edge should be on the top of the shingles and the rear edge underneath the shingles.

•NOTE: The remote fan unit must be sealed between the roof (or outside wall) and the underside

of the flange with roofing mastic to prevent leaks.

4. Connect the remote fan (CFMR1000 & CFMR1400) to the exhaust system’s round duct. Use an

adjustable elbow to attach to the roof angle.

5. Using duct tape, seal all joints to prevent air leaks.

6. NOTE: Clearance to combustible materials is 0”.

CONNECTING THE 3-SPEED FAN CONTROLTO THE REMOTE FAN

1. Power supply required for remote fans are 15 amps. @ 120V. AC, 60Hz. connected per local codes.

2. Run three #14 AWG wires (black, white and green) from the power supply at the electrical circuit panel

in the hood J-box (see Figure 6).

3. Run five wires from hood J-box through the walls to the remote fan, using color coded wires

corresponding to color codes in diagram (see Figure 7. Page 6)

4. Locate the white plastic Moldex electrical connector in the hood. This connector feeds the power to the

remote fan. Use the receptacle connector provided with the fan and plug to the connector in the hood.

Within the J-box, connect the black, white, red and blue wires from the remote fan to the black, white,

red and blue wires of the “pigtail”. Connect the green (ground) wire to the ground wire from the service

panel (see Figure 6.)

WIRINGAWALL-MOUNTED 3-SPEED FAN CONTROL

1. Use 4 Position switch (OFF –LOW –MED –HIGH).

2. Power supply required for these ventilators is 15 amps. @120V. AC, 60Hz. connected per local codes.

3. Run three #14 AWG wires (black, white and green) from the power supply at the electrical circuit panel

to the wall box (see Figure 7).

4. Run electrical conduit per local code from wall box to bottom of remote fan as shown (see Figure 7).

5. Run five #14 AWG wires in conduit between ventilator J-box and 4 position switch. Use color coded

wires corresponding to colors shown (see Figure 7).

6. Use wire nuts to connect wires as shown (see Figure 7).

INLINE BLOWER INSTALLATION FOR INLB300, INLB600 & INLB1200

NOTE: All models use the same housing/enclose

1. Before making any electrical connection make sure your electric is turned off

2. Check that the fan’s impeller is moving freely

3. Unit is designed to be mounted in any position

4. For ideal implementation, close proximity of the blower to its discharge point will improve the unit’s

performance

5. Accessibility to the unit location is important in the planned duct run.

6. When unit is not in its ideal location use larger duct work for longer runs.

7. Sheet metal screws are provided for “L” bracket attachment to the housing. Screws must be positioned

within 1” of the edge of the housing.

8. Seal all ducting connections with cold weather metal tape.

9. The unit should be hung on the “L” brackets using wood screws (not provided).

10. Rubber padding may be added to the insulation of the unit to reduce/eliminate potential vibrations (not

provided).

WARNING: ELECTRICAL CONNECTIONS SHOULD ONLY BE MADE BY A LICENSED ELECTRICIAN

CLEANING

1. Periodically check exhaust exit for blockage, i.e., bird nests, leaves, etc

2. Periodically inspect the unit ducting and the ventilation exit point for grease build-up

3. If present in the installation, periodically check the dapper for any obstructions.

INSTALLATION - POSITIONS

WARNING

1. Use ¾” plywood to mount and separate from ceiling joists bed.

2. Install additional support cross members to truss for a suspended mount.

3. Install additional support cross members to truss for horizontal mounting.

4. Install additional blocking to mount under the roof rafter.

5. Install additional cross members to ceiling joists with a 90 degree elbow to exit side.

Important Notes:

•Adding plywood to each installation may simplify install.

•10” diameter ducting is recommended for optimal performance of this product. 8” diameter may be used

if ducting space is limited but this may reduce the unit’s performance.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Blue Star Lüfter Handbücher

Blue Star

Blue Star BS-PL30240 Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung