Bluestream HEX31WP-TX Bedienungsanleitung

HEX31WP-TX

User Manual

RevA0 HEX31WP-TX User Manual

HEX31WP-TX USER MANUAL

02 www.blustream.com.au |www.blustream.co.uk

Contents

Surge protection device

recommended

This product contains sensitive

electrical components that may be

damaged by electrical spikes, surges,

electric shock, lightning strikes, etc. Use

of surge protection systems is highly

recommended in order to protect and

extend the life of your equipment.

Thank you for purchasing

this product.

For optimum performance and safety,

please read these instructions carefully

before connecting, operating or

adjusting this product. Please keep this

manual for future reference.

Introduction 03

Features 03

Panel Descriptions 04

Output On/O Function 05

Auto Switching 06

USB Type C 06

Mounting the HEX31WP-TX 06

EDID Control 07

Loading A Custom EDID 07

RS-232 Configuration 08

RS-232 Commands 08 - 09

Product Schematic 10

Specification 11

Package Contents 11

Maintenance 11

Installer Notes 12 - 13

HEX31WP-TX USER MANUAL

03contact support@blustream.co.uk | support@blustream.com.au

Our HEX31WP HDMI / USB-C wall plate HDBaseT™ Transmitter is a multi-format

4K input switcher solution delivering HDMI and USB-C inputs up to 70m at 1080p

(40m at 4K 60Hz 4:2:0). The HEX31WP-TX features both manual or automated

source selection and includes display on / o control via CEC, RS-232 and IR (via

compatible HDBaseT™ Receiver / Matrix). The HEX31WP-TX has been designed

to work with all Blustream HDBaseT™ Receiver and Matrix solutions, be installed

in both UK and European backboxes, and can be powered locally or from

compatible Blustream HDBaseT™ products.

Introduction

• Features 2 x HDMI & 1 x USB-C inputs with manual / auto source selection

• Advanced HDBaseT™ technology oering distribution of video and audio over a single CAT cable

• Supports 4K UHD video up to 40m (3840 x 2160 @30Hz 4:4:4, 4096 x 2160 @24Hz 4:4:4, and 4K @60Hz 4:2:0)

• Extends HDMI at 1080p up to a distance of 70m

• USB-C input for Video / Audio interface with Windows®, Mac® & Chromebook™ PC’s as well as tablets or

smartphones using the same connector type

• Supports all known HDMI audio formats including Dolby TrueHD, Dolby Atmos, Dolby Digital Plus and DTS-HD

Master Audio transmission

• Input selection via front panel and RS-232

• Programmable ON / OFF button utilising IR, RS-232 or CEC for control of display device at HDBaseT™ Receiver

• Supports 12V-48V PoC from compatible Blustream HDBaseT™ Receiver / Matrix products

• Bi-directional RS-232 pass through

• Supports IR pass-through to HDBaseT™ device

• Compatible with all Blustream HDBaseT™ Receiver / Matrix products*

• Magnetic faceplate surround allowing both UK & EU backbox compatibility

• HDCP 2.2 compliant

*Technical performance is subject to the features supported on the connected HDBaseT™ device

FEATURES:

HEX31WP-TX USER MANUAL

04 www.blustream.com.au |www.blustream.co.uk

Front Panel Description

1USB-C Input - Type C USB port to connect to USB-C source device

2Output ON / OFF Button - Triggers the output on / o sequence (see Output On / O section on next page)

3HDBaseT™ link status indicator - Illuminates when the Transmitter is connected to the Receiver / Matrix successfully

4IR Receiver - Built in IR sensor for IR pass through

5HDMI Input 1 - Type A HDMI port to connect HDMI source device

6HDMI Input 2 - Type A HDMI port to connect HDMI source device

7Auto Switching Button - Press to change source, hold for 3 seconds to enable / disable auto signal sense switching

8HDMI Input 2 Indicator - Illuminates when HDMI 2 input is connected

9USB Input Indicator - Illuminates when USB-C input is connected

qHDMI Input 1 Indicator - Illuminates when HDMI 1 input is connected

wRS-232 - 3-pin phoenix connector for RS-232 pass through to / from compatible HDBaseT™ Receiver / Matrix products

e12V DC Input - 2-pin phoenix connector to connect to Blustream 12V power supply (supplied)

rIR Receiver Input - 3-pin phoenix connector to connect to Blustream IR Receiver (phoenix block supplied, IR Receiver

not supplied)

tHDBaseT™ Output - RJ45 HDBaseT™ port to connect to the HDBaseT™ input port of the compatible Blustream

HDBaseT™ Receiver / Matrix device

4 5 6 7

Rear Panel Description

1211 13 14

HEX31WP-TX USER MANUAL

05contact support@blustream.co.uk | support@blustream.com.au

Output On/O Function

The HEX31WP-TX features a variety of ways that the unit can be automated to, or allow for, the powering of the display

connected to the HDBaseT™ receiver.

Output On/O Button

The Output On/O button can be programmed to power on, or o, the display connected to the HDBaseT™ Receiver

via CEC, IR or RS-232 as required by the user. The default setting on the unit is enabled for CEC (Consumer Electronic

Control), but disabled for IR and RS-232. When triggered, the Display On/O button will be illuminated. When removing

the last source device connection from the HEX31WP-TX, the display will (by default) remain powered.

The default function can be disabled (or re-enabled) as required - see below. Or refer to the RS-232 command section

of this user manual on page 08 for the full list of function commands.

Output On/O via CEC

As outlined above, the HEX31WP-TX wallplate, by default, will send out a Power On command via CEC automatically

when a video signal is sensed by the unit.

To disable this automatic feature via RS-232, send the following command:

CECAUTO OFF

To enable this automatic feature via RS-232, send the following command:

CECAUTO ON

Output On/O via IR Learning

The HEX31WP-TX can be programed to issue an IR command, via HDBaseT™ to the connected display device, when it

either detects a new signal / loss of signal, or when pressing the Output On/O button on the wall plate. To learn an IR

command into the unit, follow these steps:

1) Press and hold both Output On/O and Auto Switching buttons simultaneously for approximately 3 seconds until

both of the button LED’s flash alternately.

2) Use the Output On/O button to select between the command to be set as follows:

• A quick flashing LED for the Output On/O button indicates that Output On mode is selected

• A slow flashing LED for the Output On/O button indicates that Output O mode is selected

3) Within 30 seconds, point the IR remote control that you wish to learn at the IR sensor on the HEX31WP-TX and press

the respective button on the IR remote control.

4) The Output On/O button LED will stop flashing, and remain lit to indicate that the IR command has been learnt.

5) Press and hold the Auto Switching button for approximately 3 seconds until both the button LED’s turn o to exit IR

learning mode. The unit will return to normal operation 5 seconds aer.

Output On/O via RS-232

To enable RS-232 commands to be triggered on signal sense/loss or via the Output On/O button, send the following

commands via RS-232 to the unit:

1) To configure a command to be sent on signal sense, use the following RS-232 command:

RS232ON y:z:a

2) To configure a command to be sent on signal loss, use the following RS-232 command:

RS232OFF y:z:a

where: y = a: ASCII, h: HEX

z = 1: 2400, 2: 4800, 3: 9600, 4: 19200, 5: 38400, 6: 57600 (Default), 7: 115200

a = RS-232 command to be sent

You can also disable the RS232ON/OFF command by replacing y:z:a with DISABLE in the above commands.

HEX31WP-TX USER MANUAL

06 www.blustream.com.au |www.blustream.co.uk

Auto Switching

The HEX31WP-TX can automatically switch sources based on when an input signal is detected or lost. This feature will

automatically switch to any new source that is connected to the HEX31WP-TX, and subsequently will switch back to the

previous source when a signal is lost.

To enable or disable this feature, press and hold the the Auto Switching button for 3 seconds. The Auto Switching

button LED will blink to confirm this command has been received.

The Auto Switching button will remain lit when auto switching is enabled.

USB Type C

The USB-C input of the HEX31WP-TX gives instant connectivity with laptops and smart devices with USB-C, negating

the requirement of having to use USB-C to HDMI adaptors to obtain AV connectivity.

Not all USB-C cables support the transfer of Video and Audio. A type 3.1 USB-C cable must be used to ensure AV can

be transferred over the USB-C cable. The cables supplied with laptops or mobile devices are normally reserved for

charging only and are generally not type 3.1.

The USB-C input of the HEX31WP-TX does not support charging of mobile devices.

Mounting the HEX31WP-TX

The HEX31WP-TX has been designed to fit into a standard UK or European double-gang backbox. The mounting holes

are hidden under the magnetic faceplate on the le / right (for UK backboxes), and top / bottom (for EU backboxes).

A minimum backbox depth of 40mm is required, however, due to the normal operating temperature of HDBaseT™

equipment, we would recommend using a deeper backbox (47mm) to assist with additional heat displacement and air

circulation to the rear of the unit.

Prior consideration should be made to the choice of backbox, with particular emphasis to the location/s of cable entry

so that the maximum bend radius of the CAT cable is not exceeded.

If mounting the wallplate into a counter top, table top, or lecturn, a backbox may not necessarily be required. Please

see below technical drawing of the unit for overall and cut-out dimensions:

HEX31WP-TX USER MANUAL

07contact support@blustream.co.uk | support@blustream.com.au

EDID Control

EDID (Extended Display Identification Data) is a data structure that is used between a display and a source. This data

is used by the source to find out what audio and video resolutions are supported by the display. By pre-determining

the video resolution and audio format of the source and display device you can reduce the time needed for EDID hand

shaking thus making switching quicker and more reliable. Configuration of the EDID settings for each input can be

achieved using the following RS-232 commands to specify the required EDID:

EDIDxxDFzz

Where xx = Input: 00 refers to ALL inputs; 01 = input 1 (HDMI 1); 02 = input 2 (HDMI 2); 03 = input 3 (USB-C)

zz = EDID as shown below:

zz=00: HDMI 1080p@60Hz, Audio 2ch PCM

zz=01: HDMI 1080p@60Hz, Audio 5.1ch PCM/DTS/DOLBY

zz=02: HDMI 1080p@60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD

zz=03: HDMI 1080i@60Hz, Audio 2ch PCM

zz=04: HDMI 1080i@60Hz, Audio 5.1ch PCM/DTS/DOLBY

zz=05: HDMI 1080i@60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD

zz=06: HDMI 1080p@60Hz/3D, Audio 2ch PCM

zz=07: HDMI 1080p@60Hz/3D, Audio 5.1ch PCM/DTS/DOLBY

zz=08: HDMI 1080p@60Hz/3D, Audio 7.1ch PCM/DTS/DOLBY/HD

zz=09: HDMI 4K2K@30Hz, Audio 2ch PCM

zz=10: HDMI 4K2K@30Hz, Audio 5.1ch PCM/DTS/DOLBY

zz=11: HDMI 4K2K@30Hz, Audio 7.1ch PCM/DTS/DOLBY/HD

zz=12: HDMI 4K2K@60Hz 4:2:0 8 bit, Audio 2ch PCM

zz=13: HDMI 4K2K@60Hz 4:2:0 8 bit, Audio 5.1ch PCM/DTS/DOLBY

zz=14: HDMI 4K2K@60Hz 4:2:0 8 bit, Audio 7.1ch PCM/DTS/DOLBY/HD

zz=15: DVI 1280x1024@60Hz, Audio None

zz=16: DVI 1920x1080@60Hz, Audio None

zz=17: DVI 1920x1200@60Hz, Audio None

zz=18: DVI 1920x1200@60Hz, Audio 2ch

zz=19: Copy User EDID 1 - see below

zz=20: Copy User EDID 2 - see below

zz=21: EDID Pass through

Loading A Custom EDID

A custom EDID file can be loaded into the HEX31WP-TX. Some custom EDID’s can be found on Blustream’s website, or

use a 3rd party EDID tool to create a custom EDID. To load an EDID onto the HEX31WP-TX complete the following steps:

1) Rename the EDID file to be “EDID.bin”

2) Copy the EDID.bin file to a USB drive

3) Connect the USB drive to the HEX31WP-TX Micro-USB upgrade port (a USB to Micro USB cable may be required)

4) Connect your PC to the HEX31WP-TX RS-232 port via a serial RS-232 cable, see page 06 for RS-232 information

5) Send the command: EDID SAVE zz (where zz = 19 or 20 - see above) to save the EDID from the USB onto the

HEX31WP-TX into EDID position 19 or 20

6) Send the command: EDID 00 DF zz to recall the EDID for all inputs where zz is the position the EDID (19 or 20)

HEX31WP-TX USER MANUAL

08 www.blustream.com.au |www.blustream.co.uk

RS-232 Configuration

The RS-232 port is used for configuration / control of the product, including pass through of RS-232 commands to a

compatible Blustream HDBaseT™ Receiver / Matrix device.

The default RS-232 communication settings are:

Baud rate: 57600

Data bit: 8

Stop bit: 1

Parity bit: none

Common Mistakes

• Carriage return – Some programs do not require the carriage return where as other will not work unless sent directly

aer the string. In the case of some Terminal soware the token <CR> is used to execute a carriage return. Depending

on the program you are using this token maybe dierent. Some other examples that other control systems deploy

include \r or 0D (in hex)

• Spaces – Blustream commands do not require space between commands unless specified. There may be some

programs that require spacing in order to work.

- How the string should look is as follows OUT01FR02

- How the string may look if spaces are required: OUT{Space}01{Space}FR{Space}02

• Baud rate or other serial protocol settings not correct - please confirm the settings being used match the RS-232

configuration settings above.

RS-232 Commands

? Print Help Information

HELP Print Help Information

STATUS Print System Status And Port Status

INSTA Print All Input Status

OUTSTA Print All Output Status

CTRLSTA Print All Control Status

RESET Reset System To Default Setting

KEY ON/OFF Set System Key Control On Or O

OUT xx FR yy Set Output xx From Input yy

Input: yy [01-03]

01 = HDMI 1

02 = HDMI 2

03 = USB-C

OUT xx SWITCH yy Set Output xx Auto Switching To aa

aa = AUTO

aa = MAN

NOSIGDLY xxx Set No Signal Delay Timeout to xxx

IR ON/OFF Set System IR Control On Or O

HEX31WP-TX USER MANUAL

09contact support@blustream.co.uk | support@blustream.com.au

EDID xx DF zz EDID xx DF zz Set Input xx EDID To Default EDID zz

xx=[00]: All Input Port, [01...03]: Input Port

zz=00: HDMI 1080p@60Hz, Audio 2ch PCM

zz=01: HDMI 1080p@60Hz, Audio 5.1ch PCM/DTS/DOLBY

zz=02: HDMI 1080p@60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD

zz=03: HDMI 1080i@60Hz, Audio 2ch PCM

zz=04: HDMI 1080i@60Hz, Audio 5.1ch PCM/DTS/DOLBY

zz=05: HDMI 1080i@60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD

zz=06: HDMI 1080p@60Hz/3D, Audio 2ch PCM

zz=07: HDMI 1080p@60Hz/3D, Audio 5.1ch PCM/DTS/DOLBY

zz=08: HDMI 1080p@60Hz/3D, Audio 7.1ch PCM/DTS/DOLBY/HD

zz=09: HDMI 4K2K@30Hz, Audio 2ch PCM

zz=10: HDMI 4K2K@30Hz, Audio 5.1ch PCM/DTS/DOLBY

zz=11: HDMI 4K2K@30Hz, Audio 7.1ch PCM/DTS/DOLBY/HD

zz=12: HDMI 4K2K@60Hz 4:2:0 8 bit, Audio 2ch PCM

zz=13: HDMI 4K2K@60Hz 4:2:0 8 bit, Audio 5.1ch PCM/DTS/DOLBY

zz=14: HDMI 4K2K@60Hz 4:2:0 8 bit, Audio 7.1ch PCM/DTS/DOLBY/HD

zz=15: DVI 1280x1024@60Hz, Audio None

zz=16: DVI 1920x1080@60Hz, Audio None

zz=17: DVI 1920x1200@60Hz, Audio None

zz=18: HDMI 1920x1200@60Hz, 2ch/6ch PCM

zz=19: Copy User EDID 1

zz=20: Copy User EDID 2

zz=21: EDID Passthrough

EDID xx CP yy Set Input xx EDID Copy From Output yy

xx = Input on product (00 refers to ALL inputs, 01 = input 1 etc)

yy = Output on product (00 refers to ALL outputs, 01 = output 1 etc)

EDIDSAVE zz Save EDID File From USB Into User Slot zz

zz=19: User EDID 1

zz=20: User EDID 2

CECAUTO ON/OFF Set Auto CEC Commands When Detecting Video Input Signal On Or O

OUT xx CEC INPUT yy Send Output xx CEC Input yy Command

OUT xx CEC VOLUP Send Output xx CEC Vol Up Command

OUT xx CEC VOLDOWN Send Output xx CEC Vol Down Command

OUT xx CEC MUTE Send Output xx CEC Mute Toggle Command

OUT xx CEC PON Send Output xx CEC Power On Command

OUT xx CEC POFF Send Output xx CEC Power O Command

OUT xx CEC yy:yy:yy Send Output xx CEC yy.yy.yy Command

RS232BAUD z Set RS-232 Baud rate To x

z = 1: 2400, 2: 4800, 3: 9600, 4: 19200, 5: 38400, 6: 57600 (default), 7: 115200

RS232ON y:z:a When Detecting A Triggering Signal, Automatically Send y Type Of Command a To The

Third-party Device Whose Baud Rate Is z

RS232OFF y:z:a When Not Detecting A Triggering Signal, Automatically Send y Type Of Command a To

The Third-party Device Whose Baud Rate Is z

RS232ON DISABLE Disable Automatic RS-232 Commands When Detecting Signal

RS232OFF DISABLE Disable Automatic RS-232 Commands When Not Detecting Signal

RS-232 Commands Continued...

HEX31WP-TX USER MANUAL

10 www.blustream.com.au |www.blustream.co.uk

RS-232

HDMI

Infrared

Cat 6

USB-C

DC Power

HEX31WP-TX

Example Schematic

HDMI & USB-C SOURCE

HDBaseT™ RX

Control Processor

Optional PSU when not

powered via HDBaseT™

Compatible Blustream HDBaseT™ Matrix or Receiver product.

* Technical performance is subject to the features supported

on the connected HDBaseT™ device.

Display

Inhaltsverzeichnis

Andere Bluestream Sender Handbücher

Bluestream

Bluestream HEX31WP-TX-US Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung