BNB Solutions BAS-1000 Leitfaden
1
AVL-GSM User Installation Manual
2011.5.04
BNB Solutions Co., Ltd.
2
FCC Information to User
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution
Modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired
operation
IMPORTANT NOTE:
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
3
Revision
version date revision basis engineer name reason of revision
0.0 2011.03.10 Son, Ki-bong draft
0.1 2011.05.04 Son, Ki-bong I/O Port Modify
4
List of Contents
1. Introduction......................................................................................................................................................................4
2. Composition.....................................................................................................................................................................4
1) Basic components.................................................................................................................................................4
2) Accessories for separate sale ...........................................................................................................................5
3. Main body of the AVL-GSM......................................................................................................................................6
1) Front ...........................................................................................................................................................................6
2) Rear .............................................................................................................................................................................7
4. Product specification.................................................................................................................................................10
5. RF specification............................................................................................................................................................10
1) GSM operating frequency ..............................................................................................................................10
2) GSM Antenna.......................................................................................................................................................10
3) GPS Antenna ........................................................................................................................................................10
6. Installation ..................................................................................................................................................................... 12
5
1. Introduction
This machine is a device to transmit car locations in real time through the GSM network
with the embedded GSM module and GPS module to the designated server. You can
check a current location and route on the Web. Also you can enjoy more diverse and
more convenient functions with RS-232 telecommunication by installing accessories
additionally
2. Composition
1) Basic components
(1) Main body of the AVL GSM
(2) (GSM+GPS) unified antenna
(3) Power cables
Color: TBD
6
Length: 3M
2) Accessories for separate sale.
(1) Thermograph & interface cable
Install a temperature sensor at the place to measure the temperature. You may
measure the temperature by installing it at a car cargo section. Send the
measured temperature data to the AVL-GSM, which transmits the data to the
designated server.
(2) Digital tachograph and interface cable
This product installed in the car provides in real time the information including
car overspeed, idling, quick-acceleration, and quick-deceleration. It is
recommeded to install the digital tachograph at a garage or the designated shop.
(3) Panic button
In case of emergency, press the button to the server. The following picture
shows a button as an example.
(4) Keypad
After connecting it with the body of AVL-GSM, if you press each button, its
applicable information is transmitted to the server.
7
(5) Relay and cable
The followings are the exterior relay for car ignition interlock and cables.
3. Main body of the AVL-GSM
1) Front
① Status indicating LED
GPS LED is a red LED and blinks every seconnd when a GPS module works
normally.
GSM LED is a green LED and blinks during the storage of the data to be
transmitted by the terminal. While data is transmitted to the server, it stays
on and becomes off after transmission.
② SIM: port to insert a SIM card
③ I/O: 5 pin connector of a Molex 5268A type
8
PIN NO Description
① Panic Button: optional (3) connected with a panic
button
② Not used
③ Not used
④ Car_Stop_Out: optional (5) connected with a car
ignition interlock relay
⑤ Ground
④ RST: Reset switch
2) Rear
① GSM
It is a SMA type connector to be connected with a GSM cable of (GSM+GPS)
unified antenna. Be careful not to connect the GSM cable of (GSM+GPS) unified
antenna with the below GPS connector.
② GPS
9
It is a SMA type connector to be connected with a GPS cable of (GSM+GPS)
unified antenna. Be careful not to connect the GPS cable of (GSM+GPS) unified
antenna with the above GSM connector.
③ TEMP
It is a 3 pin connector of a Molex 5268A type to be connected with (1)
thermograph, an optional accessory. Be careful not to connect the thermograph
with the “TACHO & DEBUG” port explained hereunder.
PIN NO Description
① TEMP_TX232
② GND
③ TEMP_RX232: It receives data of the
thermograph.
④ KEY
It is a RJ45 connector to be connected with (4) keypad, an optional accessory.
PIN NO Description
① KEY_GPIO_1
② KEY_GPIO_2
③ KEY_GPIO_3
④ KEY_GPIO_4
⑤ Ground
⑥ KEY_GPIO_5
⑦ Not used
⑧ 3.3V
10
⑤ TACHO & DEBUG
It is a 3 pin connector of a Molex 5268A type for firmware downloading or to be
connected with (2) digital tachograph, an optional accessory. Be careful not to
be connected with the above mentioned thermograph.
PIN NO Description
① TACHO_DEBUG_TX232
② GND
③ TACHO_DEBUG_RX232
⑥ DC 6-24V
It is a 5268A 4Pin connector of Molex type to be connected with power cable.
PIN NO Description
① VCC_IN: Connect this with a car battery + terminal
(12V or 24V)
② Battery_BackUp: Connect this to the power inlet (cigar
jack or radio power socket) after turning on the car
ignition key, or connect to “IGN1”, “IGN2”, or “ACC”
pin according to the automobile manual.
③ Ground: Connect this with a car battery – terminal
(Ground).
④ Ground: Connect this with a car battery – terminal
(Ground).
Connect the power cables in the picture below with the above pin numbers
correctly.
Inhaltsverzeichnis
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
