Bodet Time Sigma H Anleitungen und Rezepte

Sigma H master clock

Upon receipt, always check the product for damage during shipment. If any is found, you may le a damage claim with the carrier.

SIGMA

Installation and start-up instructiond

BODET SA

1 rue du Général de Gaulle

49340 TREMENTINES

Tél: 02 41 71 72 99

Fax: 02 41 71 72 01

Usine de Trémentines

Système de

Management certifié

Réf : 606528 Z

www.bodet-time.com

Table of contents

1) General 4

2) Safety rules 5

3) Description 7

4) Installation 8

4.1 Mechanical installation 8

4.2 Electrical connections 9

Connection for D1D2 distribution : 10

Connection of DHF transmitter : 11

5) Installation examples 12

5.1 Set the 24V impulse output 12

5.2 Set the DHF output 12

5.3 Set a 24V TBT output 13

6) Keypad: Key functions 14

7) Main menu programming 16

7.1 Standby state 16

7.2 User menu 16

7.3 USB loading and backup 17

7.4 Adding DHF receivers 17

7.5 Access code 18

7.6 Time and date 19

7.7 Dynamic radio reception 20

7.8 Language 20

7.9 Version 20

8) Technician menu programming 21

8.1 Time synchronisation menu 22

8.1.1 Programmable time changeover 23

8.1.2 Setting the time base 24

8.2 Time output management menu 25

8.3 Function setting menu 27

8.4 CPU software download menu 28

8.5 Factory setting restoration menu 28

9) Alarm messages 29

10) Technical characteristics 31

11 ) Appendix: Time Zones predened 33

12 ) What to do if ...? Check that … 35

SIGMA H

Installation and start-up instructions

1) General

The Sigma is a master clock which can be used to control receiver clocks.

The SIGMA has functions which can be programmed from the technician

menu.

On rst installation, it is essential to program the technician menu (see

page 21) before the customer menu.

It is also essential when installing the SIGMA to program the technician

functions in the order in which they appear in the menu.

This product must be installed in a residential, commercial or light industry

environment.

Bodet declines all responsibility in the event of an accident resulting from use

not in accordance with the recommendations of this manual.

CAUTION :

Any modication on the product renders the guarantee null and void.

Checking the equipment:

One SIGMA master clock.

This instruction manual.

To verify the model of the master clock,

press the key. SIGMA H

2) Safety rules

• Maintenance of this equipment must be carried out by qualied

personnel.

• If the SIGMA is connected to the 230 V mains power supply, its installation

must comply with the European standard IEC 364 (NFC 15.100 for France).

PROTECTIONS :

• 110-230V version: the mains supply for this device must include a neutral

phase circuit breaker of maximum 6 A C curve, rapidly accessible upstream

from the supply.

• 24V DC version: the SELV 24 V power supply for this device must include a

protection of maximum 6 A.

• 36-72V DC version: the SELV 36-72 V power supply (according to NFC 15-

100) for this device must include a protection of maximum 6 A.

• The circuit breaker must be switched off during maintenance operation.

Refer to labels in the product.

• All cables must be attached either to the wall (wall-mounted version) or

to the frame of the cabinet (Rack version) before being connected to the

various terminals strips, to prevent any pulling on these terminal strips. In

addition, the wires of each terminal strips must be attached to each other to

maintain the various isolations if an initial fault occurs.

• The time distribution cables must not run alongside high power mains

cables (to avoid interference with communication between the SIGMA and

the clocks).

• The SIGMA must be attached (to the wall or on its support) before being

switched on.

• “Rack” models must be mounted in a slide-in unit for 19” cabinets or racks.

These components will provide mechanical, electrical and re protection

(only the front panel may remain accessible).

• IMPORTANT: before any installation, refer to the “technical

characteristics” paragraph.

•

Caution :

• In case of replacement of the CR2032

battery, it is IMPERATIVE to respect the

polarity following the opposite indications.

• There is risk of explosion if the battery is

replaced by a battery of incorrect type.

• Dispose of used batteries according to the

instructions of the manufacturer.

3) Description

Wall box

A) LCD screen

B) Keypad (see page 14)

C) Alarm indicator light (red

LED)

D) Mains indicator light (green

LED)

19” Rack

A B

4) Installation

4.1 Mechanical installation

Choose a room with low temperature variations

away from any source of electrical interference

(contactors, motors, etc.).

WALL-MOUNTED version: Unscrew the 2

screws on the front, remove the cover (for the

lower cover, press on the 2 clips (N) and slide it

upwards). Disconnect the at jumpers (Q) (be

careful to connect them the same way round

on reassembly) and attach the SIGMA to the

wall. When your unit is in place, remove the

protective lm on the keypad.

RACK version: Install the rack in its slot in an

electrical bay or cabinet.

4.2 Electrical connections

Connect the cables (mains power supply, impulse line or AFNOR output and

radio synchronisation input, depending on the model) to the corresponding

terminal strips as shown in the gure below.

(*) See page 25, the “Time outputs” menu to set this output (Pulse minute,

½ minute, second 24V or power TBT 24VDC 1A).

(**) depending on the SIGMA model.

RACK version: The mains power supply, impulse line and AFNOR output and

radio synchronisation input terminal strips are directly accessible at the rear of

the Rack slide-in unit.

(**) 110 to

230VAC or

24VDC

36/72VDC

Circuit C1

Circuit C2

Circuit C3

GPS input

DCF

radio input

(*) Minute, ½ mn or

second 24V, or SR2-59

Afnor output

DHF output

External input

See the limit

characteristics of

these circuits on

page 31

Attach the wires to each other, near

the terminal strips.

Connection for D1D2 distribution :

D1 D2 uses the relays of circuits 1 and 2

Circuits must be protected by fuse disconnector or circuit breaker 4A

maximum. Indicate on the label above the terminal block the location of

these protections.

ND1 D2 To Bodet

D1D2

movement.

Make a shunt between

terminals 1 and 3, 0.75² <

cross section of wires <1.5².

Inhaltsverzeichnis

Beliebte Netzwerkzeitserver Handbücher anderer Marken

EKOS

EKOS EKOSync 1588 Bedienungsanleitung

Meinberg

Meinberg LANTIME M200/GPS Gebrauchs- und Pflegehandbuch

Meinberg

Meinberg LANTIME M600 Gebrauchs- und Pflegehandbuch

Meinberg

Meinberg LANTIME M300/MRS/AD10-AD10 Gebrauchs- und Pflegehandbuch

TPA

TPA S5 Bedienungsanleitung

Meinberg

Meinberg LANTIME M300/GPS/2LNE/AD10-AD10 Gebrauchs- und Pflegehandbuch

Gorgy Timing

Gorgy Timing LEDI NETWORK iTS Bedienungsanleitung

Mobatime

Mobatime DTS 4160.grandmaster Bedienungsanleitung

Meinberg

Meinberg LANTIME M300/GNS/RPS Gebrauchs- und Pflegehandbuch

Mobatime

Mobatime DTS 4128.timeserver Bedienungsanleitung

Meinberg

Meinberg IMS LANTIME M1000 Bedienungsanleitung

BRG Precision Products

BRG Precision Products NTP100B Bedienungsanleitung

Krontek

Krontek KT2000 Bedienungsanleitung

Meinberg

Meinberg LANTIME M300/TCR Gebrauchs- und Pflegehandbuch

Mobatime

Mobatime NTS Bedienungsanleitung

Bodet

Bodet NETSILON 7 AC Bedienungsanleitung

Meinberg

Meinberg LANTIME M100 Bedienungsanleitung

Tekron

Tekron NTS 02-G Bedienungsanleitung