Tekron NTS 02-G Bedienungsanleitung

NTS 02-G

USER MANUAL

 
TEK-NTS02G-MNL-v3-032020 P a g e | 2 www.tekron.com 
 
© 2020 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The information in this 
document is provided for informational use only and is subject to change. For further information or support, go to: ww.tekron.com. 
 
 
 
 
 
 
Contents 
Contents..............................................................................................................................................................................................................................2 
1. Introduction.....................................................................................................................................................................................................4 
2. Front Panel.......................................................................................................................................................................................................6
LED Indicators............................................................................................................................................................................................................................9 
USB Port:.....................................................................................................................................................................................................................................10 
3. Back Panel.......................................................................................................................................................................................................11
P1 Power Input..........................................................................................................................................................................................................................11 
Earth Stud (M4 Nut)..............................................................................................................................................................................................................11 
Ant: Antenna Connector (SMA Connector)..............................................................................................................................................................11 
Antenna and Lead-in Cable Considerations............................................................................................................................................................12 
P2: IRIG-B Input (3-pin 3.81 mm Connector)............................................................................................................................................................12 
P3: Programmable Output (3-pin 3.81 mm Connector).....................................................................................................................................12 
P4: Alarm Relays (4-pin 3.81 mm Connector).........................................................................................................................................................13 
ADMIN/ETH 1: Ethernet Administration Port (RJ45).........................................................................................................................................13 
ETH 2 & ETH3 Ethernet Communication Ports (RJ45)................................................................................................................................14 
4. Software...........................................................................................................................................................................................................15 
Configuration Tool.................................................................................................................................................................................................................15 
USB driver...................................................................................................................................................................................................................................15 
5. Factory Hardware Options...................................................................................................................................................................16 
Power Supply Options.........................................................................................................................................................................................................16 
Slave Only Option (Fiber input)......................................................................................................................................................................................16 
1. INSTALLATION...........................................................................................................................................................................................17
Identification.............................................................................................................................................................................................................................17 
Location.......................................................................................................................................................................................................................................17 
Power Supply............................................................................................................................................................................................................................17 
Hazardous Voltage................................................................................................................................................................................................................17 
Mounting the NTS 02-G.....................................................................................................................................................................................................17 
Operation....................................................................................................................................................................................................................................18 
2. Appendix..........................................................................................................................................................................................................19

TEK-NTS02G-MNL-v3-032020 P a g e | 3 www.tekron.com

document is provided for informational use only and is subject to change. For further information or support, go to: ww.tekron.com.

NTS 02-G Specifications....................................................................................................................................................................................................19

3. Warranty Statement................................................................................................................................................................................20

4. Notes.................................................................................................................................................................................................................20

TEK-NTS02G-MNL-v3-032020 P a g e | 4 www.tekron.com

document is provided for informational use only and is subject to change. For further information or support, go to: ww.tekron.com.

1. Introduction

The NTS 02-G Network Time Server provides a precision time reference for synchronizing Ethernet

networks. The NTS 02-G features multiple independently-addressed Ethernet Ports each supporting the

NTP protocol. Each NTS 02-G base unit has a built-in GNSS-synchronized master clock which, in the default

operating mode, provides the source reference time used by all of the Ethernet ports. It follows, therefore in

terms of Network Time Protocol (NTP) definitions, that all NTS 02-G Ethernet Ports are Stratum 1 sources.

The NTS 02-G product is ideally suited for use in industrial environments and can provide NTP server

functions to multiple independent Ethernet networks.

All NTS 02-G units feature a front panel display (See figure 1) giving visual feedback about the time data

Figure 1 NTS 02-G: front and back panels

TEK-NTS02G-MNL-v3-032020 P a g e | 5 www.tekron.com

document is provided for informational use only and is subject to change. For further information or support, go to: ww.tekron.com.

The NTS 02-G features an administrative 10/100 Mb Ethernet port through which the units inputs and

outputs can be configured.

Configuration software which is available to download from www.tekron.com. Optional accessories include

antenna, low loss antenna cable, antenna pipe mounting components and lightning protection kit.

2. Front Panel

Figure 2 NTS 02-G front panel

The NTS 02-G features two LED indicators on the front panel (See figure 2), together with a USB port and a

2-line by 16-character backlit LCD display.

SYNC LED: This LED shows the status of the current sync source.

ALM LED: This LED shows the alarm status of the NTS 02-G.

ADMIN (USB) Port: This port may be used to configure the clock using the Tekron Configuration Tool

available for download on the Tekron website.

LCD Display:

On initial power-up, the LCD display shows a copyright message, along with the serial number and revision

level of the unit (See figure 3a). Approximately 10 seconds after power-up, if the NTS 02-G is operating in its

default mode as a GNSS-synchronized Grand Master Clock, then the display changes automatically to

indicate that it is waiting for satellites (See figure 3b). Once one or more satellites have been discovered, it

transitions to the operating default display (See figure 3c). Figures 3d and 3e show alternative time displays

that the user can access by pushing the button on the front panel between the LED indicators. Successive

button-pushes can be used to cycle through all the display screens in turn. Examples of the display screen

share shown below:

TEK-NTS02G-MNL-v3-032020 P a g e | 7 www.tekron.com

document is provided for informational use only and is subject to change. For further information or support, go to: ww.tekron.com.

3a Start up (Clock ID)

3b Waiting for satellites

3c Operating default

3d Local time

3e UTC Time

3g IP Address

3f - Alarm

Figure 3 LCD display screens

of screen 3c

time day-of-year and time-of-day are on the bottom line.

Screen 3c shows that the clock is operating with a local time offset of 12 hours ahead of UTC. The local date

is 17th March 2013, and the local time is 11:16:53 in the morning.

Screen 3d shows the same time and date, but also indicates that the time displayed is Local Standard Time,

in screen 3d

Screen 3e shows the UTC time and date which is 11:16:53 on the evening of Monday 17th March 2013.

Screen 3g shows the basic Ethernet network settings for Admin/ ETH 1 port. In this example it shows the

port has been configured with a fixed IP address of 192.168.96.10.

The display screens in Figure 3b, 3c, 3d and 3e, each show a three-character status field at the bottom right-

hand side of the display. When the NTS02-G is operating in its default modeas a GNSS-synchronized Grand

Master, this field provides further details about the GNSS function as shown in fig 4a and table 1a below.

When the NTS 02-G n IRIG-B source, this field directly indicates the sync source. (see

SLC alternate sync sources supported by the NTS 02-G.

NTS 02-GVer. 3.05R

WAITING FOR SATS

GPS RX STAT: 00A

UTC+1200 17MAR13

076 11:16:53 87P

LST: TUE 17MAR13

076 11:16:53 87P

Fixed:

192 . 168 . 96 . 10

UTC: MON 16MAR13

075 23:16:53 87P

*** ANT L ***

075 23:16:53 80P

TEK-NTS02G-MNL-v3-032020 P a g e | 8 www.tekron.com

document is provided for informational use only and is subject to change. For further information or support, go to: ww.tekron.com.

LST: TUE 17MAR13

076 11:16:53 87P

Satellites in sky

Satellites tracked

GNSS Receiver Mode

LED INDICATORS Table 1a GNSS Status

Character

Values

Description

Satellites

in the sky

- 9 : 0 - 9

- E : 10-14

Represents the total number of satellites currently present in the sky according

to the GNSS NTS 02-G has lost its

knowledge of the GNSS

been in storage for an extended period, or if the GNSS receiver has been reset. It

may take up to two hours for the NTS 02-G to operate normally again.

Satellites

tracked

- 9 : 0 - 9

- E : 10

This digit represents the number of satellites currently being used to compute

see

3.6 below as described under (2.1) below.

GNSS

Receiver

Mode

NTS 02-G in Acquisition mode - attempting to get satellite fixes.

best accuracy cannot be obtained, but the unit will still attempt to synchronize

to UTC.

Site Survey in progress. NTS 02-G is synchronized and is refining the position

calculation for higher precision. Once complete the mode will change to Position

hold.

now known precisely, and the NTS 02-G is providing

its most accurate time, typically within 40 ns of UTC.

LED INDICATORS Table 1b Alternative Sync Source

Character

Values

Description

Alternate

Sync

Source

SLC

Clock is synchronized to an IRIG-B source on P2 input

Clock is synchronized to an IRIG-B source on the Fiber input

function for further details

If the clock is configured to synchronize to IRIG-B only (ignore GNSS)

Figure 4a GPS Receiver Status Figure 4b IRG-B Source

LST: TUE 17MAR13

076 11:16:53 SLC

TEK-NTS02G-MNL-v3-032020 P a g e | 9 www.tekron.com

document is provided for informational use only and is subject to change. For further information or support, go to: ww.tekron.com.

will be displayed in the status field if there is no IRIG-B signal input.

LED Indicators

The SYNC LED shows the status of the sync source. The various states are shown as follows:-

Off: The NTS 02-G has no power.

On: The NTS 02-G is synchronized to the source indicated by the LCD display

Slow Flash (1 flash per second): The NTS 02-G -

running)

Fast Flash (5 flashes per second): The NTS 02-G is not synchronized.

The ALM LED indicates the internal alarm status of the NTS 02-G. It has only two operating states:-

Off: The NTS 02-G is operating normally. i.e., there are no alarms

Fast Flash: (5 flashes per second): Alarms are active. In this case, the actual alarm state is shown on the top

line of the LCD display, replacing the normal date information (see example infig 3f above).

Alarm State

Definition

*PwrA*

Power A: Power is not present on the Power A (P1A) input

*PwrB*

Power B: Power is not present on the Power B (P1B) input

*Hold*

Holdover: The clock has lost sync, but the outputs are still active and indicating the

appropriate loss of accuracy (oscillator drift).

*Sync*

Lost sync: The clocks has lost sync, the holdover time has expired and the outputs are not

active

*AntL*

Antenna Low: An under-current state has been detected on the antenna input (antenna

disconnected)

*AntH*

Antenna High: An over-current state has been detected on the antenna input (antenna

short circuit)

*Sats*

Satellites Low: The number of satellites have fallen below the user configured threshold

*IRIG*

No IRIG-B Input: This alarm appears when IRIG-B input monitoring is enabled and there is no

IRIG-B input signal.

*IPex*

Link Local Address: The port has been configured for DHCP and could not obtain an

address, and has rolled back to a linked local address: 169.254.X.X.

eX represents the port number which has the alarm.

Table 1 - Alarm Definitions

TEK-NTS02G-MNL-v3-032020 P a g e | 10 www.tekron.com

document is provided for informational use only and is subject to change. For further information or support, go to: ww.tekron.com.

USB Port:

A USB port (type B) is provided to support local configuration/administration. The NTS 02-Gconfiguration

software supports both USB and Ethernet configuration.

Andere Handbücher für NTS 02-G

Inhaltsverzeichnis

Andere Tekron Netzwerkzeitserver Handbücher

Tekron

Tekron NTS 02-G Bedienungsanleitung

Beliebte Netzwerkzeitserver Handbücher anderer Marken

EKOS

EKOS EKOSync 1588 Bedienungsanleitung

Meinberg

Meinberg LANTIME M200/GPS Gebrauchs- und Pflegehandbuch

Meinberg

Meinberg LANTIME M600 Gebrauchs- und Pflegehandbuch

Meinberg

Meinberg LANTIME M300/MRS/AD10-AD10 Gebrauchs- und Pflegehandbuch

TPA

TPA S5 Bedienungsanleitung

Meinberg

Meinberg LANTIME M300/GPS/2LNE/AD10-AD10 Gebrauchs- und Pflegehandbuch

Gorgy Timing

Gorgy Timing LEDI NETWORK iTS Bedienungsanleitung

Mobatime

Mobatime DTS 4160.grandmaster Bedienungsanleitung

Meinberg

Meinberg LANTIME M300/GNS/RPS Gebrauchs- und Pflegehandbuch

Mobatime

Mobatime DTS 4128.timeserver Bedienungsanleitung

Meinberg

Meinberg IMS LANTIME M1000 Bedienungsanleitung

BRG Precision Products

BRG Precision Products NTP100B Bedienungsanleitung

Krontek

Krontek KT2000 Bedienungsanleitung

Meinberg

Meinberg LANTIME M300/TCR Gebrauchs- und Pflegehandbuch

Mobatime

Mobatime NTS Bedienungsanleitung

Bodet Time

Bodet Time Sigma H Anleitungen und Rezepte

Bodet

Bodet NETSILON 7 AC Bedienungsanleitung

Meinberg

Meinberg LANTIME M100 Bedienungsanleitung