Bodypoint LH600S Leitfaden
en
Leg Harness
INSTALLATION AND USER’S INSTRUCTIONS
ART NOS. LH600S, LH600M & LH600L
WARNING! Product should be installed and tted
by a qualied rehab technician.
For installation, this product should be mounted with:
• Flat-mount end-ttings
• Cinch-mount end-ttings
• Cam buckle (1” suitable for users up to 75kg,
1-1/2” and 2” suitable for all users)
Optional Bodypoint belt mounting hardware may
be used for mounting to wheelchairs and seating
systems.
INTENDED USE:
WARNING! This product should only be used for
positioning a person in a wheelchair or work chair. It
is NOT intended for use as a transportation safety
device, as a personal restraint device, or in any other
application where its failure could result in injury.
Misuse of this product is unauthorized and unsafe.
WARNING! This pelvic positioning belt must be
worn correctly tted across the thighs at all times.
Have your seating specialist demonstrate its proper
adjustment and use.
• Accidental release of this belt can allow the user to
slip down or fall from the wheelchair.
• A user’s inability to self-release can be hazardous if
the user slips down or is trapped in the wheelchair
in an emergency.
If the user’s physical or cognitive abilities prevent
them from safely operating this belt, a caregiver must
be present at all times during its use. Ensure that all
caregivers know how to correctly adjust and unfasten
the product.
WARNING! As with any new seating support,
this product may change the way a person sits. Users
must continue to practice regular pressure relief
activities and skin integrity checks, not only where
this product contacts the user, but also in primary
pressure-bearing areas such as the sacrum, legs, and
buttocks. If increased skin redness or irritation occurs,
discontinue use and consult your physician or seating
specialist. Failure to do so may result in serious injury,
such as pressure ulcers.
WARNING! If a serious incident occurs related to
the use of this product, it should be reported to the
manufacturer (Bodypoint, Inc.) and the local Compe-
tent Authority.
PERIODIC SAFETY AND PERFORMANCE CHECKS:
To ensure user safety, this product must be checked
periodically for function and signs of wear. If the
product does not function correctly or if signicant
wear is found in the buckles, mounting points, web-
bing, padding, or stitches, stop using it and contact
your supplier for qualied repair or replacement
by Bodypoint. Under no circumstance should this
product be altered or repaired by unqualied persons
— health and safety depend on it!
CLEANING: Machine wash, hot,
60°C (140°F). Do not bleach. Tumble dry, low tem-
perature, or drip dry. Do not iron. (Placing the prod-
uct inside a cloth bag during washing helps prevent
scratches to the product and the machine.)
SCRAP/DISPOSAL: Product is made of materials
which can be disposed of safely without special
precautions at the end of its useful life.
WARRANTY: This product carries a limited lifetime
warranty against defects in workmanship and
materials arising under normal use by the original
consumer. Contact your supplier or Bodypoint for
warranty claims.
These instructions provide important information for the safe use and maintenance of
all Bodypoint Leg Harness. Give these instructions to the user or their caregiver and
review them to ensure that they are understood.
BPI048-en 2021.10
A
N
S
I
|
R
E
S
N
A
I
S
O
T
E
S
T
E
D
© 2021 Bodypoint, Inc. All Rights Reserved.
Bodypoint Europe BV
Kerkstraat 29
7396 PD Terwolde
The Netherlands
Medical
Device
PACKAGE CONTENTS
• Leg Harness
• Cinch-Mount™ or Flat-Mount™ End Fittings
• FrameSaver™ Clamps (Optional – Art No, FS032-2)
FRONT STRAP
1. Pass the strap under the thigh, and
locate desired anchor point at front
of seat rail or under seat.
2. Attach end ttings to wheelchair frame.
INSTALLATION REQUIREMENTS
• #2 Philips screwdriver.
• Mounting screws with a minimum pullout strength
of 200lbs /90kg. Not included in package.
en
Ø 3/16–1/4” (5–6mm)
#2 Phillips
ORIENTATION
Seat user in wheelchair and
establish correct posture. Place Leg
Harness pad against inner thigh
with rear strap end passing near
the pelvis and hip joint. Pad should
touch the seat, but not extend
under the leg or touch groin area.
REAR STRAP
1. Rear straps should be
anchored to the rear
of the seat rail
2. Locate desired anchor
point and attach end
ttings to wheelchair
frame.
DIRECT MOUNTING
End ttings can be attached
directly to solid seat
surfaces. Mounting screws
must have minimum pullout
strength of 200lbs/90kg.
(Not included in package.)
ADJUSTMENT
Tighten Leg Harness on user with D-ring
strap. Remove any extra slack from web-
bing at rear end tting. When properly ad-
justed and the straps tightened, it should
t snug so the user’s legs are secure.
SAFETY CHECK
When properly positioned in wheelchair, have user lean
forward and side to side to check t. Check for:
1. Normal operation of buckles and adjustment straps.
2. Comfort–Look for areas of irritation.
3. Interference with other devices–Relocate anchor points
as necessary.
4. Move chair through full range of motion, including tilt,
folding, and rolling. Check for any interference.
Cinch-Mount™
FrameSaver™ Flat-Mount™
Ø 7/8” (22mm)
Ø 1” (25mm)
Ø 3/4” (19mm)
(Art. No.
HW303-19SHIM)
Dieses Handbuch passt für folgende Modelle
2
Andere Bodypoint Sicherheitsausrüstung Handbücher
Beliebte Sicherheitsausrüstung Handbücher anderer Marken
Innova
Innova Xtirpa Bedienungsanleitung
bolle SAFETY
bolle SAFETY B810 Bedienungsanleitung
SHENZHEN FANHAI SANJIANG ELECTRONICS
SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung
Hiltron security
Hiltron security POWER8E Leitfaden
Hatco
Hatco B-950P Bedienungsanleitung
Sitec
Sitec TX MATIC Bedienungsanleitung
