Bolt CBP-UC Bedienungsanleitung

UNIVERSAL COMPACT BATTERY PACK

For Hot-Shoe Flashes

User Manual

2 |Introduction

Thank you for choosing Bolt.

The Bolt Universal Compact Battery Pack increases your ﬂash count and boosts the recycle speed of your ﬂash.

It oers a compact design with universal attachment to the most popular ﬂash brands and operates with a range

of AA batteries, making it easy and convenient to use.

Precautions

⚠⚡

• Please read and follow these instructions, and keep

this manual in a safe place.

• Do not attempt to disassemble or repair this product.

There are components inside that can produce a

hazardous electric shock.

• Keep this product and AA batteries away from children.

• Clean the unit with only a soft, dry cloth.

• If you detect smoke or a burning smell coming from

the battery pack, immediately stop operation. Once

smoking has subsided, remove the batteries to prevent

the product from igniting or melting, and take the

product to an authorized service center for repair.

• Keep this unit away from water and any ﬂammable

gases or liquids.

• Remove all batteries from the battery pack before

long-term storage. Do not store or use this product at

temperatures above 104°F (40°C).

• To avoid overheating and damaging your ﬂash unit,

wait at least 10 minutes after 20 continuous ﬂashes

at full power. Refer to your ﬂash unit’s manual for

information on its continuous full-power ﬂash capacity

and limitations.

• Images are for illustrative purposes only.

Precautions |3

Battery Warnings

• Always follow the warnings and instructions printed

on the batteries to avoid activities that could cause

the batteries to leak corrosive liquid, generate heat,

or explode.

• Use in environments with moderate temperatures.

When some battery types get cold, they lose some

of their ability to supply power. However, this does

not mean that they have lost their charge, and they

will regain the ability to supply power when their

temperature returns to a more moderate level.

• To conserve battery life, turn the ﬂash unit o or

disconnect the Compact Battery Pack from it during

long standby periods. Very little power is consumed

when the pack is in standby mode. The amount may

vary according to working conditions and the speciﬁc

ﬂash model used with the pack.

• High temperatures can cause some battery types to

drain more quickly.

• Dispose of batteries properly. Never heat them

or throw them into a ﬁre, as this could cause the

batteries to leak corrosive liquid, generate heat, or

explode.

• Don’t ﬁre more than 20 full-power ﬂashes in a row,

as this can overheat and damage your ﬂash. Refer

to your ﬂash unit’s manual for information on its

continuous full-power ﬂash capacity and limitations.

4 |Overview

Overview

Compact Battery Pack

1 Shoulder strap holes

2 Mounting screw passthrough

3 Flash connection cable

4 Flash cable connector

5 Status LED

6 Battery compartment

7 Battery compartment cover

8 1/4-20 mounting screw

9 Rubber washer

CBP-U

• Do not attempt to disassemble or repair this product yourself.

Doing so can produce a dangerous electric shock.

• Keep out of reach of children.

• Install 4 AA batteries when charging with a single circuit, or 8

AA batteries when charging with two circuits.

• Always install AA batteries of the same type, brand, and age.

• Do not ﬁre rapid bursts of more than 20 ﬂashes. After 20

continuous ﬂashes, stop using the pack for at least 10 minutes.

CBP-U /

Universal

Compact Battery Pack

DA1010

Made in China

1 5

Overview |5

Soft Case

1 Cable strap

2 Bottom snap closure

3 Battery strap

4 Belt strap

5 Top touch-fastener support

Flash Power Cords

(Sold Separately)

6 CBP-UC: Canon

7 CBP-UN: Nikon

8 CBP-US: Sony

3 4 5

6 |Battery Installation

Battery Installation

The versatile Universal Compact Battery Pack can be used with three AA battery types:

• Alkaline (1.5 V)

• Lithium (1.5 V)

• Nickel-metal hydride (NiMH) (1.2 V)

Using eight batteries will enable faster ﬂash recycle

times.

To install batteries, unplug the battery pack from your

ﬂash unit and follow these steps:

1. Press down on the battery compartment cover and

slide the cover in the direction of the arrow.

Battery Installation |7

2. Insert four or eight batteries in the open

battery bays, making sure the polarity

is in the right orientation, and that

each set of four batteries is installed as

shown.

3. Slide the cover back over the battery

compartment until secure.

Important!

Replace all batteries at the same time. Do

not mix battery types or brands, or new and

used batteries together.

8 |Connecting to Your Flash

Connecting to Your Flash

Align the ﬂash cable connector with the

separate ﬂash power cord to connect them.

Then plug the other end of the ﬂash power

cord into your ﬂash.

Make sure the connector is correctly aligned

with the pins and alignment grooves on the

power port. Forcing a connector into a port

upside down can damage both your ﬂash and

the Compact Battery Pack connector.

Connecting to Your Flash |9

Important!

• The connectors should easily attach. Forcing a connector can damage both your ﬂash and the Compact

Battery Pack connector.

• Batteries must be installed in the ﬂash before you connect it to the Universal Compact Battery Pack. Most

ﬂash units require batteries to be installed in order to operate.

• You may need to conﬁgure the custom function on your ﬂash unit to make it draw power from the battery

pack. Refer to your ﬂash unit’s instructions for more information.

• Disconnect the Compact Battery Pack from your ﬂash unit before storing it.

LED Status Indicator

Canon and Sony ﬂashes: The indicator displays a solid light in both standby and recycle modes.

Nikon ﬂashes: The indicator displays a solid light in recycle mode and turns o in standby mode.

10 |Mounting & Carrying Your Compact Battery Pack

Mounting and Carrying Your Compact Battery Pack

The Compact Battery Pack comes with a soft case and mounting screw that make it convenient and

unobtrusive to use.

Using the soft case

Wear the Compact Battery Pack on your belt

for better distribution of weight. Make sure the

pack is correctly oriented in the soft case, so

the status LEDs are visible through the small

openings at the top.

Using the mounting screw

You can use the mounting screw to attach the

Universal Compact Battery Pack to the bottom of

your camera:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bolt Batteriepack Handbücher

Bolt

Bolt VD-420 Bedienungsanleitung

Bolt

Bolt Cyclone Bedienungsanleitung

Bolt

Bolt CYCLONE PocketMax PP-1000 Bedienungsanleitung

Bolt

Bolt CBP-C1 Bedienungsanleitung

Bolt

Bolt Cyclone DR PP-400BP Bedienungsanleitung

Bolt

Bolt P12 Bedienungsanleitung

Bolt

Bolt CYCLONE DR PP-5800BP Bedienungsanleitung

Bolt

Bolt Cyclone DR PP-400DR Bedienungsanleitung

Beliebte Batteriepack Handbücher anderer Marken

Acumentrics

Acumentrics PACK-POWER SYSTEM Bedienungsanleitung

ACDC Dynamics

ACDC Dynamics SPF12-50 Bedienungsanleitung

Aegis

Aegis ABL-72020P Bedienungsanleitung

Dyness

Dyness TowerESS Bedienungsanleitung

Growatt

Growatt APX 5.0P-S0-US Bedienungsanleitung

EGO

EGO BAX1300 Bedienungsanleitung

CyberPower

CyberPower BCA Series Bedienungsanleitung

Intermec

Intermec 700 Series Bedienungsanleitung

Dometic

Dometic PLB40 Bedienungsanleitung

V-TAC

V-TAC VT-48280-W2 Bedienungsanleitung

Valence

Valence RT Bedienungsanleitung

Nikon

Nikon MB-D14 Bedienungsanleitung

IOGear

IOGear GBP24V Series Bedienungsanleitung

Inventus Power

Inventus Power PROTRXion S-12V100-TRX-HD Bedienungsanleitung

Clas Ohlson

Clas Ohlson PW-290A Bedienungsanleitung

EINHELL

EINHELL MULTI-Ah Power X-Change Plus Bedienungsanleitung

Samsung

Samsung EB-U3300 Bedienungsanleitung

ECTIVE

ECTIVE LC Series Bedienungsanleitung