BOMBARDIER CC670−51111 Bedienungsanleitung
ASSEMBLY
1. General
A. After the components have been repaired and cleaned, obey the assembly instructions for the
Tuning Select control panel (refer to Repair, Pageblock 23−81−04_6001 and Cleaning,
Pageblock 23−81−04_4001).
B. Do the unpacking of electrical/electronic components as follows:
(1) Obey all the local safety regulations for handling electronic components that contain
electrostatic−sensitive devices (ESDS), as applicable. Many components have microprocessors
and memory devices that can be damaged by electrostatic discharges. Always wear a wrist
strap and make sure you are correctly grounded before you remove the ESDS components from
their packages.
C. Assembly must be performed on a clean workbench in a room free from dust and moisture. Parts
must be protected from impact damage.
2. Assembly
Refer to Figure 1001, Refer to Figure 1002.
NOTE: All item numbers shown in parentheses ( ) are the same item numbers are used in the
Illustrated Parts List (IPL).
A. Assemble the Tuning Select control panel as follows:
(1) Install the electrical connector (100) as follows:
(a) Install the posts (70) on the mounting plate assembly (50) with the screws (75).
(b) Install the connector (100) on the posts (70) with the screws (105).
(2) Install the ATC SEL 1 STBY 2 rotary switch (90) as follows:
(a) Install the ATC SEL 1 STBY 2 rotary switch (90) on the mounting plate assembly (50) with
the washer and the nut (part of (90)).
NOTE: When you install a new switch, remove and discard one nut, one lock washer and
one rubber washer supplied by the vendor.
(b) Remove the tags and connect the electrical wires to the switch (12).
(3) Install the FMS TUNE INHIBIT toggle switch (95) on the Tuning Select control panel as follows
(for CC670−51111−3, CC670−51111−7, CC670−51111−27, and CC670−51111−31 only):
(a) Install the FMS TUNE INHIBIT toggle switch (95) on the mounting plate assembly (50) with
the nut, the locking ring (part of (95)) and the washer (110).
NOTE: When you install a new switch, remove and discard one nut and one lock washer
supplied by the vendor.
(b) Remove the tags and connect the electrical wires to the switch (95).
(4) Install the RTU 2 INHB switch/light (20) as follows:
B
COMPONENT MAINTENANCE MANUAL
TUNING SELECT CONTROL PANEL
PART NUMBER CC670−51111
23−81−04 Page 7001
Nov 10/2013
(a) Install the RTU 2 INHB switch/light (20) with the connector (40) on the mounting plate
assembly (50).
(b) Install the gasket (part of (20)) on the illuminated lens (35).
(c) Install the illuminated lens (35) on the RTU 2 INHB switch/light (20).
(d) Remove the tags and connect the electrical wires to the connector (40).
(5) Install the RTU 1 INHB switch/light (20) as follows:
(a) Install the RTU 1 INHB switch/light (20) with the connector (40) on the mounting plate
assembly (50).
(b) Install the gasket (part of (20)) on the illuminated lens (30).
(c) Install the illuminated lens (30) on the RTU 1 INHB switch/light (20).
(d) Remove the tags and connect the electrical wires to the connector (40).
(6) Install the (panel lamp) connector (80) as follows:
(a) Put the connector (80) in position on the mounting plate assembly (50).
(b) Install the solder lug, the washer and the nut (part of (80)) on the connector (80).
(c) Connect the wires to the terminals on the connector (80).
(7) Install the standby tune control unit (45) as follows:
(a) Install the standby tune control unit (45).
(b) Safety the standby tune control unit (45) with the latches.
(8) Install the plastic panel (5) as follows:
(a) Install the plastic panel (5) on the mounting plate assembly (50).
(b) Attach the plastic panel (5) with the rubber washers (15) and the screws (10).
(c) Install the knob (85).
B
COMPONENT MAINTENANCE MANUAL
TUNING SELECT CONTROL PANEL
PART NUMBER CC670−51111
23−81−04 Page 7002
Nov 10/2013
Inhaltsverzeichnis
Andere BOMBARDIER Bedienfeld Handbücher
