Bosch BE 300 LSN Bedienungsanleitung

Installation Instructions

BE 300 LSN

- 1 - 610-4.998.101.907

A3 Sept. 2001

Installation procedure and technical data

Cable routing:

1. The data cables are strain-relieved and

stripped directly after entering the cable

entry point.

Strip the cables to the required length (up

to the marked area (1) + approx. 10 cm)).

2. Very important: Pull insulating sheathing

over the auxiliary shielding wires.

3. Route the cable wires together with the

auxiliary shielding wire in the direction of

the marked area (1) (see next page for

maintenance position). 1

Slot Slot

Remove the top of the casing:

1. Press a screwdriver into the slots in the

bottom of the casing in order to raise the top

of the casing slightly.

2. Swing the bottom part of the top of the

casing approx. 45° relative to the bottom of

the casing. Pull off the top part to the front.

Fitting the bottom of the casing:

1. Cable entry points for recessed

cabling (1).

2. Cable entry points for surface-

routed cabling (2).

3. Cable entry point if the unit is

fitted over a recessed socket (3).

4. Recommended bolts 2x for 4x40

installation.

1 1

2 2

3 1

Continued on page 2

Installation Instructions

BE 300 LSN

- 2 - 610-4.998.101.907

A3 Sept. 2001

Insert top of casing into maintenance position:

1. A retaining clip is located at the lower

left side of the bottom of the casing

for holding the top of the casing in

the maintenance position.

2. Hook the top of the casing into

the retaining clip from the side.

Connect data cable:

1. Solder the cable wires and auxiliary shielding wires onto the connectors.

2. Route the cable wires so as not to impair the correct functioning of the pcb

(e.g. tamper switch).

LSN1

GND

LSN2

Fit the top of the casing:

1. Remove the top of the casing from the maintenance position and fit it into the

top of the bottom section at an angle of approx. 45°.

2. Swing the top section of the casing downwards and press it firmly until it snaps

into the bottom section.

Continued on page 3

Installation Instructions

BE 300 LSN

- 3 - 610-4.998.101.907

A3 Sept. 2001

Technical data

Operating voltage

- LSN section

- Control section + 15 V ... + 31 V

+ 9.6 V ... + 30 V

Current consumption

- LSN section

- Control section max. 3,55 mA (typ. 2,9 mA)

20 mA standby / 50 mA with illumination

Tamper monitoring Tamper switch

Ambient conditions

- Operating temperature

- Storage temperature

- Degree of protection of casing

- 5° C ... + 45° C

- 20° C... + 60° C

IP 40

Casing

- Material

- Colour ABS

RAL 9010

Dimensions (H x W x D) 112 x 162 x 29 mm

Weight 0.25 kg

VdS class Class C

VdS approval G 100070

(included in NZ 300 LSN approval)

Sealing the unit:

1. Twist a locking screw

(contained in the accessories pack)

from below into the casing.

2. Seal the screw. Locking screw and seal

Attach service card:

1. Swing down the control console flap of the BE 300 LSN.

2. Stick the service card with the telephone No. of the service centre and ID

number onto the inside of the flap.

Andere Handbücher für BE 300 LSN

Andere Bosch Bedienfeld Handbücher

Bosch

Bosch Solution 64 Montageanleitung

Bosch

Bosch D7024 Kurzanleitung

Bosch

Bosch Solution 880 CC408 Bedienungsanleitung

Bosch

Bosch Easy Series Bedienungsanleitung

Bosch

Bosch D9412GV2 Bedienungsanleitung

Bosch

Bosch DS6R2 Betriebsanleitung

Bosch

Bosch ICP-EZM2 Bedienungsanleitung

Bosch

Bosch B8512G Bedienungsanleitung

Bosch

Bosch B5512 Bedienungsanleitung

Bosch

Bosch B5512 Bedienungsanleitung

Bosch

Bosch Easy Series Bedienungsanleitung

Bosch

Bosch D9412GV3 Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Bosch

Bosch CP1 Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl VDP 08.3 Bedienungsanleitung

Bosch

Bosch Easy Series Bedienungsanleitung

Bosch

Bosch FPA-5000 Benutzerhandbuch

Bosch

Bosch D7412G Bedienungsanleitung

Bosch

Bosch B6512 Bedienungsanleitung

Bosch

Bosch AMAX panel 2100 Gebrauchsanweisung

Bosch

Bosch Solution 6+6 Wireless AE Bedienungsanleitung

Bosch

Bosch D7412GV2 Kurzanleitung

Bosch

Bosch MPC-xxxx-C Series Bedienungsanleitung

Bosch

Bosch FPD-7024 Kurzanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten

Truma

Truma CP plus Bedienungsanleitung