Bosch DS3MX-E-U Bedienungsanleitung

Alarm Control Panel DS3MX-E-U

User Guide

1.0 Arming the System

Enter your personal identification number (PIN) and

press [On].

Figure 1: Alarm Control Panel

Enter a Master PIN code or a User PIN code. Press

the [On] key. If the code was entered correctly, the

red Armed indicator flashes and the system arms.

If your system has an exit delay zone, the sounder

beeps during the exit period. The exit sounder beeps

faster during the last 20 seconds of the programmed

exit delay time.

After the exit delay time expires, the red Armed

indicator glows continuously. A violation on a zone,

not programmed as a delay zone, immediately

activates a system alarm.

2.0 Disarming the System

Enter PIN, press [Off]

Enter a Master PIN code or a User PIN code. Press

the [Off] key. If a delay zone is triggered first, a code

must be entered before the expiration of the entry

delay time.

The red Armed indicator LED stops flashing and turns

off, indicating the system is disarmed.

3.0 Quick Arm

Press the [On] key for 3 seconds

If your system is programmed by the installer to allow

Quick Arm, hold the [On] key down for 3 seconds to

start the arming mode. Disarming requires entering a

User code (PIN) followed by pressing the [Off] key.

4.0 Cancel Alarm

Enter PIN, press [Off]

Enter a Master PIN code or a User PIN code and

press the [Off] key to immediately stop the alarm

output.

5.0 Panic Key

[*][#]

Your system must be programmed at

installation to use this function.

During an emergency, simultaneously pressing the [*]

and [#] keys for 3 seconds produces an alarm.

Entering a User code resets the panic alarm condition.

6.0 Alarm History Clear

Press the [#] key for 3 seconds

While in the disarmed mode, press the [#] key for 3

seconds to cancel all flashing alarm history zone

indicators.

If an alarm occurs while the system is armed, the

zone’s LED glows continuously. When the system is

disarmed, the zone causing the alarm flashes its LED

indicator. While in the disarmed mode, pressing the

[#] key for 3 seconds resets the indicator.

130 Perinton Parkway, Fairport, NY 14450-9199 USA

Customer Service: (800) 289-0096; Technical Support: (888) 886-6189

51374D

User Guide

7/0

DS3MX-E-U

Page 2 of

7.0 Bypassing a Zone

Enter PIN, press [Bypass], enter the zone

number, and press [On]

A user can bypass a zone during the arming

sequence if it was programmed at installation to

allow bypass. You can bypass a zone if the zone is

either faulted or normal. To bypass a zone, enter

the User code or the Master code. Press the

[Bypass] key. Enter the zone number to bypass

(such as, Zone 1, Zone 2, or Zone 3, or any

combination of Zones 1, 2, or 3).

For example: To enter Zone 1, press the [1] key,

then press the [On] key to begin the arming cycle

and exit delay, if programmed. All zones that were

bypassed will clear and automatically restore to

their normal mode the next time the system

disarms.

Once a zone is bypassed, the zone’s LED indicates

its bypass status by flashing twice every 2 seconds.

8.0 Fire Alarm Reset

Enter PIN, press [Reset]

Use the Fire Reset for power interrupt and to reset

the smoke detectors. This function must be installed

and programmed at installation. Only the Master

code user can perform this function.

9.0 Door Un-Lock Code

Enter PIN, press [*]

If enabled, entering the Door Un-Lock User code

and pressing the [*] key activates the Request to

Exit function, releasing any connected door lock.

Table 1: Zone Status

NAME STATUS DESCRIPTION

Zone 1 On Zone 1

alarmed/violated

Off Zone 1 normal

Flashing

(0.5 seconds on, 0.5

seconds off)

Zone 1 alarm

history

Flashes twice every 2

seconds

Zone 1 bypassed

Zone 2 On Zone 2

alarmed/violated

Off Zone 2 normal

Flashing

(0.5 seconds on, 0.5

seconds off)

Zone 2 alarm

history

Flashes twice every 2

seconds

Zone 2 bypassed

Zone 3 On Zone 3

alarmed/violated

Off Zone 3 normal

Flashing

(0.5 seconds on, 0.5

seconds off)

Zone 3 alarm

history

Flashes twice every 2

seconds

Zone 3 bypassed

Armed Flashing

(0.5 seconds on; 0.5

seconds off)

Exit delay

On System armed

Off System disarmed

Power On Power supply

normal

Off No power supply

Inhaltsverzeichnis

Andere Bosch Bedienfeld Handbücher

Bosch

Bosch Rexroth IndraControl VR 21 Series Bedienungsanleitung

Bosch

Bosch K2200 Series Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl VCP 20 Technisches Handbuch

Bosch

Bosch Solution Ultima 880 Bedienungsanleitung

Bosch

Bosch FPA-5000 Bedienungsanleitung

Bosch

Bosch Solution 6+6 Wireless AE Bedienungsanleitung

Bosch

Bosch FPA-5000 Benutzerhandbuch

Bosch

Bosch B6512 Bedienungsanleitung

Bosch

Bosch AMAX panel 2000 ICP-AMAX-P Bedienungsanleitung

Bosch

Bosch FPC-500 Bedienungsanleitung

Bosch

Bosch ICP-EZM2 Bedienungsanleitung

Bosch

Bosch D9412G Anleitung zur Verwendung

Bosch

Bosch D9412GV2 Bedienungsanleitung

Bosch

Bosch D6412 Kurzanleitung

Bosch

Bosch Rexroth VAM 10.1 Technisches Handbuch

Bosch

Bosch ICP-AMAX4-P1 Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl VCP 05 Technisches Handbuch

Bosch

Bosch CC484 Bedienungsanleitung

Bosch

Bosch D9124 Technisches Handbuch

Bosch

Bosch ICP-CC488 Bedienungsanleitung

Bosch

Bosch Solution 880 Bedienungsanleitung

Bosch

Bosch CPS21T Bedienungsanleitung

Bosch

Bosch D7212GV3 Kurzanleitung

Bosch

Bosch Solution 6+6 Wireless On/Off Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten

Truma

Truma CP plus Bedienungsanleitung