Bosch MED17.5.2 Bedienungsanleitung

info@chiptuningshop.co.uk

Manual for using MED17.5.2 Bosch ECU probe with AVD – Page 1.

1. Description: This probe can be used for programming VAG MED17.5. Bosch ECU`s. It fits in most BDM

positioning frames and is fitted with LED`s for accurate alignment on the ECU. The “Boot” resistors and the

ignition feed can be switched. With this adapter, there is no need to solder at all.

Adapter Overview

A = Serial port connection B = Power Switch ON/OFF

C = Power Jack D = DIP Switches for BOOT Resistors ON/OFF

E = Ignition selection switch:

ON/OFF/K-Line

Since the AVDI requires a permanent connection via a 510 Ohm resistor between the K-Line and 1 V, This switch

has no function in the AVDI version of this probe.

SET TO “K-Line” POS T ON AT ALL T MES

F = Connect to flash tool. G = Connect to serial port on probe (A)

Manual for using MED17.5.2 Bosch ECU probe with AVD – Page 2.

2. Handling and Adjustment: MPORTANT - Make sure that the power switch (B) is in the “OFF” position.

The power switch must remain OFF so that the pins are not live, until the probe is correctly aligned and in

contact with the corresponding pins on the ECU. Failure to follow these instructions could result in damage

to the ECU!

Place the probe into the BDM frame retaining bracket and tighten the screws. Attach the adapter cable (G) to

the serial port (A) on the probe and plug the other end (F) into the OBD cable of your flash tool. Connect the

power supply to the probe jack (C), the LED's will now turn on to aid alignment, however the probe does not

power the ECU until the power switch (B) is turned on.

Adjust the ECU on the frame and move the retainer carefully towards the ECU. Ensure that all the pins are in

their designated position.

A diagram showing the location of the connections can be found on page 3.

t is very important, that the retainer is free from backlash and moves smoothly!

3. Reading password: (This step is only necessary for TP8+). Lift up the Boot DIP switches (D) as shown in

the adapter overview on page 1 and set the Ignition switch (E) to the “ON” position, you can now read the

password.

4. Programming the ECU: Push the DIP switches (D) down and set the “Ignition” switch (E) to the “K-Line”

position, then you can proceed with programming over boot mode.

5. Disconnecting: To safely disconnect the probe from the ECU, you must first remove TURN OFF THE

POWER Switch (B). Once the power supply is disconnected it is safe to lift the frame and probe away from

the ECU.

Manual for using MED17.5.2 Bosch ECU probe with AVD – Page 3.

The pads marked in red have to make contact with the probe.

Technical alterations reserved!

This product should be operated by competent personnel only. Chiptuningshop Ltd do not accept any responsibility

for damages, direct or consequential caused by improper handling.

Inhaltsverzeichnis

Andere Bosch Steuereinheit Handbücher

Bosch

Bosch D9127U Bedienungsanleitung

Bosch

Bosch PBK Bedienungsanleitung

Bosch

Bosch MM100 Bedienungsanleitung

Bosch

Bosch KTS Truck Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl VCP 25.2 Technisches Handbuch

Bosch

Bosch Rexroth IndraControl VAC 31 Bedienungsanleitung

Bosch

Bosch KTS 5a Series Bedienungsanleitung

Bosch

Bosch D8125 Betriebsanleitung

Bosch

Bosch MKK-040 Bedienungsanleitung

Bosch

Bosch Control 8313 Bedienungsanleitung

Bosch

Bosch DS7432 Bedienungsanleitung

Bosch

Bosch Professional GCY 42 Bedienungsanleitung

Bosch

Bosch Rexroth IndraDrive CSB02 Technisches Handbuch

Bosch

Bosch rexroth PSK Gen 2 Bedienungsanleitung

Bosch

Bosch K20 RF Bedienungsanleitung

Bosch

Bosch Rexroth FMS Bedienungsanleitung

Bosch

Bosch GCY 30-4 Professional Montageanleitung

Bosch

Bosch Conettix B444-A Bedienungsanleitung

Bosch

Bosch GCC 30-4 Professional Bedienungsanleitung

Bosch

Bosch Security Systems Blue Line A1-CC Bedienungsanleitung

Bosch

Bosch RC 4001 Bedienungsanleitung

Bosch

Bosch C900TTL-E Bedienungsanleitung

Bosch

Bosch Rexroth ctrlX CORE Bedienungsanleitung

Bosch

Bosch FLM-420-NAC-D Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung