Bosch ADS-AMC2-4R4CF Bedienungsanleitung

Access Modular Controller 2

ADS‑AMC2‑4R4CF | APC‑AMC2‑4R4CF

en Installation manual

Access Modular Controller 2 Table of contents | en 3

Bosch Security Systems B.V. Installation manual 2022-03 | V03 |

Table of contents

1Safety 5

1.1 Unpacking 6

1.2 FCC compliance 6

2Short information 7

3Introduction 8

3.1 Description 8

3.2 Product overview 10

3.2.1 Mainboard 10

3.2.2 Status display 12

3.3 System overview 13

4Installing 14

4.1 Mounting the device on a mounting rail 14

4.2 Unmounting the device from a mounting rail 14

4.3 Opening the case 15

4.4 Closing the case 16

4.5 Cabling 17

4.5.1 Conductor data for powering the controller 17

4.6 Grounding and shielding 18

4.6.1 Grounding for host interface 18

4.6.2 Grounding for extension interface 19

4.6.3 Grounding for bus interfaces 19

4.7 Connecting the power supply to the controller 20

4.8 Ethernet host interface 21

4.9 RS-485 host interface 22

4.9.1 RS-485 Two Wire Connection 23

4.9.2 RS-485 Four Wire Connection 23

4.9.3 DIP switch selector 23

4.10 RS-485 for extension modules 26

4.11 RS-485 interface for card readers 27

4.11.1 RS-485 data bus system conditions 27

4.11.2 Power reader 28

4.12 Connecting relay outputs 29

4.13 Connecting analog input devices 31

4.14 Tamper protection 33

5Operating 34

5.1 Configuring Ethernet interface 34

6UL requirements 35

6.1 System requirements 35

6.1.1 Computer 35

6.2 UL 294 level descriptions 35

6.3 Installation instructions 36

6.4 Extended technical specification 38

6.4.1 RS-485 extension 38

6.4.2 Power consumption 38

7Troubleshooting 39

7.1 Resetting the software 40

7.2 Resetting the device to factory default 41

8Service and repair 42

4en | Table of contents Access Modular Controller 2

2022-03 | V03 | Installation manual Bosch Security Systems B.V.

9Disposal 43

10 Technical specifications 44

11 Appendices 45

11.1 Connecting diagrams 45

11.2 Status display 49

11.2.1 Bootloader V00.49 49

11.2.2 Firmware until 6x.45, 37.60 49

11.2.3 Firrmware xx.61, 37.71 50

11.2.4 Firmware xx.62, 37.72 51

Access Modular Controller 2 Safety | en 5

Bosch Security Systems B.V. Installation manual 2022-03 | V03 |

1 Safety

Warning!

Read instructions

Before working with the device, read these instructions carefully. Make sure you have

understood all information described in this document.

Caution!

Fire hazard and risk of electric shock due to unauthorized spare parts and accessories

Unauthorized spare parts and accessories might lack grounding wires or other safety

elements. External power supplies must be installed by qualified personnel. The service

technician must use replacement parts or accessories that are specified by the manufacturer.

Warning!

Risk of explosion of lithium battery

The battery can explode if replaced incorrectly.

Replace the battery with the same type as recommended by Bosch.

Dispose used batteries according to the instructions of the manufacturer of the batteries.

Warning!

Risk of physical injury due to blocked escape routes

This product may block escape routes if not installed correctly. To keep escape routes free:

- Use locks in fail-safe mode, so that doors can be released if power fails.

- Install manual override switches, such as break-glass or lever stations, to unlock doors in an

emergency.

Notice!

Device damage due to incorrect mounting

Mount this product on the matching mounting rails.

If the device falls or is damaged, check it before the installation.

Notice!

Considerations on local regulations

When you install the device, consider any local fire, health and safety regulations.

Notice!

Device damage due to electrostatic discharge

Protect the hardware from electrostatic discharge, especially when the device is open and

exposed. Always disconnect the controller from the power source before modifying the

installation. This product does not support hot plugging.

Notice!

Unauthorized access

If this product is installed in an unprotected environment, unauthorized people may be able

to enter.

Install the product in a location with restricted access.

6en | Safety Access Modular Controller 2

2022-03 | V03 | Installation manual Bosch Security Systems B.V.

Notice!

Some features and functions described in this document depend on the firmware loaded into

the device and host software. Make sure that the controller is updated to the firmware

version provided with the host system.

This product is RoHS compliant. See Technical data for the full table of hazardous

components.

1.1 Unpacking

Check the packaging for visible damage. If anything has been damaged during transport,

please inform the transport agency.

Unpack the product carefully. This is an electronic device that must be handled with care to

avoid damage. Do not attempt to put the product into operation if components are damaged.

If any parts are missing, inform your customer service representative or a Bosch Security

Systems salesperson. The shipping carton is the safest transport container for the unit. Store

the shipping carton and the other packaging material for future use. If the product has to be

sent back, use the original packaging.

1.2 FCC compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC rules. The limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate receiving antenna.

2. Increase the separation between the equipment and the receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Access Modular Controller 2 Short information | en 7

Bosch Security Systems B.V. Installation manual 2022-03 | V03 |

2 Short information

The AMC2 can control a maximum of eight ID readers (depending on the reader type) and fully

processes the access logic at the assigned entrances.

The device controls a group of one to eight access points. These access points, also known as

entrances, can be:

– doors

– gates

– barriers

– turn stiles

– revolving doors

– mantraps

– ID card, PIN and biometric readers

– door opening elements

– sensors.

All the product versions use encrypted connections between the access modular controller

and the host system.

The controller stores all necessary information in a battery-buffered memory and in a compact

flash storage element. Even when the unit is offline, it is able to perform:

– Independent status and authorization checks on access points

– Take access decisions

– Activate and deactivate connected peripheral elements

– Detect and register all relevant events

The Access Modular Controller (AMC) is supported by the Access Professional Edition (APE),

BIS Access Engine (ACE) and the Access Management System (AMS).

For the latest information about our products, visit our online product catalog:

www.boschsecurity.com/xc/en/product-catalog/

Manufacturing dates

For product manufacturing dates, go to www.boschsecurity.com/datecodes/ and refer to the

serial number on the product label.

Remarks

This hardware is part of a security system.

Access should be granted to authorized people only.

Some states do not allow the exclusion or limitation of implied warranties, or limitation of

liability for incidental or consequential damages, hence the above limitation or exclusion might

not apply to you.

If you need further assistance or have any questions, contact:

Bosch Security Systems B.V.

Torenallee 49

5617 BA Eindhoven

Netherlands

www.boschsecurity.com

8en | Introduction Access Modular Controller 2

2022-03 | V03 | Installation manual Bosch Security Systems B.V.

3 Introduction

3.1 Description

The controller has four independent interfaces for RS-485 type readers. It can control a

maximum of four doors with a reader in each direction and a maximum of eight doors with a

reader in one direction only.

Figure3.1: Access Modular Controller

All necessary information for access verification is stored in a battery buffered on-board

memory and a Compact Flash (CF) memory card. This guarantees autonomous access

decisions and complete access registrations even if the management host system is offline.

The built in compact flash adapter provides adequate storage capability for cardholders and

events.

The electronics of the controller are completely covered by a plastic housing. The LCD (liquid

crystal display) provides all important status information.

Unsecured Area

Secured Area

Figure3.2: Example

Access Modular Controller 2 Introduction | en 9

Bosch Security Systems B.V. Installation manual 2022-03 | V03 |

The controller can communicate upstream to the host computer using one of the following

interfaces:

– Ethernet

– RS-485 multi-dropped, not supported by:

– BIS 4.9.1 and later

– AMS 4.0 and later.

The controller has eight analog input devices and eight relay outputs. With its analog input

devices, the controller verifies, for example, if a lock is closed or open. The relay outputs can

be used, for example, to activate lock mechanisms if access is granted, or activate the burglar

alarm system if an intrusion or system alert is detected. If the eight inputs and eight outputs

on the board are not enough to configure the system, up to three additional extension boards

can be connected. The extensions offer 8 or 16 additional inputs and outputs.

In the Bosch Access Host Systems, the setup procedure for a controller is made very simple

and fast by the use of door templates. Once selected, all the inputs and outputs are

predefined. These settings can be changed to choose every free contact of the controller or a

connected extension.

10 en | Introduction Access Modular Controller 2

2022-03 | V03 | Installation manual Bosch Security Systems B.V.

3.2 Product overview

3.2.1 Mainboard

3 4 52

10 11

Figure3.3: Upper circuit board with display (front)

1 DIP switch for RS-485 address and protocol selection.

2 Lithium battery for buffering of static RAM and real time clock (RTC). The battery life

is estimated at 10 years, nevertheless an error message is generated if the voltage

sinks below a preset minimum level.

NOTICE: In order to avoid an error message caused by an earlier voltage drop we

suggest to replace the battery every 8 years. Spare part: VARTA CR 2032 PCB.

3 Reset push button - reachable through the casing using a screwdriver

4 Liquid Crystal Display

5 Push button, available on top of the housing, to select different display modes

6 Jumper: Equalization of potential between different systems and earth ground

(shield)

7 Jumper: Interface selector RS-485 host connection, RS-485 two wire or RS-485 four

wire (depends on external wiring)

8 Configurable RS-485 host interface

9 Compact flash memory

10 Project-specific interface

11 Configurable 10/100 Mbit/s Ethernet host interface

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bosch Controller Handbücher

Bosch

Bosch Rexroth lndraDrive HCS02 Series Bedienungsanleitung

Bosch

Bosch Rexroth ctrl CORE Bedienungsanleitung

Bosch

Bosch Junkers TR 100 Bedienungsanleitung

Bosch

Bosch LTC 8600 Bedienungsanleitung

Bosch

Bosch DSA-N2E8XG-12AT Bedienungsanleitung

Bosch

Bosch FW 200 Bedienungsanleitung

Bosch

Bosch REG 73-1 Bedienungsanleitung

Bosch

Bosch Access Modular Controller 2 Bedienungsanleitung

Bosch

Bosch BAT 251 Bedienungsanleitung

Bosch

Bosch CLIMATE 5000 VRF RDCI Series Bedienungsanleitung

Bosch

Bosch Rexroth NYS04.2-ST-02-LMSN-NY4073 Bedienungsanleitung

Bosch

Bosch FW 100 Montageanleitung

Bosch

Bosch MPC-8000-C Bedienungsanleitung

Bosch

Bosch WORCESTER GREENSTAR WIRING CENTRE Benutzerhandbuch

Bosch

Bosch K 30 RF Bedienungsanleitung

Bosch

Bosch Heatronic 4000 Handbuch

Bosch

Bosch AMC-4W Bedienungsanleitung

Bosch

Bosch CR 10 Bedienungsanleitung

Bosch

Bosch Rexroth OptiFeed-FS EcoDrive 03 FLP04VRS Bedienungs- und Montageanleitung

Bosch

Bosch HPC Bedienungsanleitung

Bosch

Bosch AVENAR panel 8000 Bedienungsanleitung

Bosch

Bosch Rexroth IndraControl VPB 40.3 Bedienungsanleitung

Bosch

Bosch Rexroth REFUspeed RS51 Bedienungsanleitung

Bosch

Bosch AMC2 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch