Bosch Readykey K6199-CNCii Gebrauchs- und Pflegehandbuch

Firmware Update Kit

Multi-Site Central

Network Controller

Read

K6199-CNCii

Readykey K6199-CNCii | Firmware Update Kit | 1.0 Description EN | 2

Bosch Security Systems | 10/03 | 17019v2.1

1.0 Description

Do not attempt this update unless the PC

software (such as Readykey for Windows)

is the current version.

Use the supplied EPROM to update the firmware

contained in an existing Multi-Site MKII Central

Network Controller to the current production version.

The version is indicated by the version number in the

form Vx.yz.

Table 1: Contents of Kit

1 EPROM Marked 1 of 1

Figure 1: Multi-Site Central Network Controller

21 3 4 5 6 7 8

12 13

1 - PSU

2 - 6WB

3 - Host PC

4 - RS-232 1

5 - RS-232 2

6 - RS-232 3

7 - External reader

connection

8 - Expansion port

9 - Heat sink

10 - Battery

11 - EPROM 1 of 1

12 - LED

13 - Internal reader

Readykey K6199-CNCii | Firmware Update Kit | 2.0 Installation EN | 3

Bosch Security Systems | 10/03 | 17019v2.1

2.0 Installation

Use anti-static handling precautions at all

times while following this procedure.

Discharge any static build-up by touching

the metal backplate.

Keep all components in their packaging

until needed.

2.1 Remove Cover

1. Remove the six-wire bus cable, if fitted, and any

serial RS-232 cables, except the host PC cable,

from the CNC. Ensure that all transactions were

received from the CNC (indicated by no events

appearing on the screen or printer for at least one

minute, and ** MONITORING ** displaying on

the screen).

2. Remove the power supply and host PC

connections.

3. Remove the six screws securing the cover. These

screws are located on the underside of the unit,

three on each side. Do not remove the three

screws along the front of the unit securing the front

bezel.

4. Remove the cover by sliding it towards the back,

revealing the main circuit board. Located just to

the right of the center of the board, the EPROM is

recognizable by the white sticker labeled with the

firmware version number.

2.2 Replace the Firmware

1. Note the orientation of the EPROM (refer to

Figure 2). There is a small dimple on the right-hand

edge of each chip resting in the socket.

2. Insert the two hooks of an IC extractor tool into

the slots provided (corner to corner) on the

mounting.

Damage caused by not using a proper IC

extractor tool voids any warranty.

3. Close the tool until the hooks fit under the

EPROM.

4. Squeeze the extractor tool to remove the EPROM.

5. Position the replacement EPROM and gently push

into the socket. When inserting the EPROM,

ensure the orientation is correct by lining up the

"squared off" corner of the EPROM with the

matching corner of the mounting.

6. Replace the cover.

Figure 2: Removing the EPROM

1 - IC extractor tool

2 - EPROM

3 - Slots for hooks

4 - “Angled” corner indicates orientation EPROM

mount

5 - Hooks

2.3 Check for Normal Operation

1. Reconnect the power supply and ensure the

display shows PC OFF-LINE.

2. Reconnect the CNC to the computer (host PC

port). Do not connect any other cables at this time.

3. Start up the Readykey for Windows on the

computer.

4. Initialize the CNC from Installer: Masters in

Readykey for Windows.

5. Check the display of the CNC and verify the CNC

displays ** MONITORING **.

6. Reconnect the six-wire bus, if fitted, and any serial

RS-232 cables.

7. Verify all door controllers re-established

communications.

Error reporting may be more extensive than

before, particularly from serial sites.

17019v2.1

Bosch Security Systems

130 Perinton Parkway

Fairport, NY 14450-9199

Customer Service: (800) 289-0096

Technical Support: (888) 886-6189

Andere Bosch Controller Handbücher

Bosch

Bosch MAP Benutzerhandbuch

Bosch

Bosch rexroth SB11 Bedienungsanleitung

Bosch

Bosch FW 200 Bedienungsanleitung

Bosch

Bosch CR 20 RF Bedienungsanleitung

Bosch

Bosch Rexroth CS660 Gebrauchs- und Pflegehandbuch

Bosch

Bosch EasyControl CT200B Bedienungsanleitung

Bosch

Bosch BRC3100 Bedienungsanleitung

Bosch

Bosch B443 Bedienungsanleitung

Bosch

Bosch Junkers TR 100 Bedienungsanleitung

Bosch

Bosch Rexroth ctrlX CORE X7 Bedienungsanleitung

Bosch

Bosch Rexroth lndraDrive HCS02 Series Bedienungsanleitung

Bosch

Bosch Rexroth Diax 04 Bedienungsanleitung

Bosch

Bosch KJR-120C1/BTF-E Betriebsanleitung

Bosch

Bosch ADS?AMC2?2WCF Bedienungsanleitung

Bosch

Bosch BRC3100 Bedienungsanleitung

Bosch

Bosch HPC Bedienungsanleitung

Bosch

Bosch PVA-4CR12 Bedienungsanleitung

Bosch

Bosch Rexroth 31 Series Gebrauchsanweisung

Bosch

Bosch BRC3100 Bedienungsanleitung

Bosch

Bosch Worcester TDS 10 Bedienungsanleitung

Bosch

Bosch LTC 8600 Bedienungsanleitung

Bosch

Bosch Rexroth IndraDrive C HCS03.1 Technisches Handbuch

Bosch

Bosch CLIMATE 5000 VRF RDCI Series Bedienungsanleitung

Bosch

Bosch Rexroth IndraDrive M Technisches Handbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch