Bosch EL800A Bedienungsanleitung

IMPORTANT NOTICE

Please read this user manual carefully. It contains important information

on the Smart Door Lock and maintenance.

Make sure that the mechanical key is kept in a safe place outdoors, i.e.

inside your car, office etc.

Do not expose the lock to rain, sunlight and outdoor environments.

Do not try to repair/disassemble the lock to avoid unnecessary loss.

Do not hit the lock with any hard objects.

Make sure that the door is properly locked when you are going out.

Do not use water or any chemical substances such as oil or benzene to

clean the lock. This will result in short circuit, ageing and/or paint

stripping.

Make sure to change your PIN Code regularly.

Do not use rechargeable batteries for the lock. This product is only

compatible with alkaline batteries.

The virtual PIN Code is up to 32 digits. E.g. Actual PIN Code + **** or **** +

Actual PIN Code (Do not key in garbled character before or after the virtual

PIN Code).

If the touch screen is out of order, try to restart the device with the

emergency power supply below, which is connected to the Micro-USB.

When using the key to open the lock, please turn the key back to its

original position before removing it.

Please follow the above instructions to avoid any injuries and/or damages

on the lock.

USER MANUAL

BOSCH SMART LOCK

Do not put any flammable material such as gas, paint, gasoline,

etc, near the smart lock to avoid explosion and fire, including

explosive materials such as alcohol, gasoline, etc.

We are not responsible for any damage or property loss resulting

from improper installation, readjustment, use and/or repair by

user or third parties.

EL800A

PRODUCT INTRODUCTION

OUTER BODY PARTS

INNER BODY PARTS AND LOCK CASE

SPECIFICATIONS

Outer Lock Size: 20(D)x80(W)x400(H)mm

: 65(D)x80(W)x400(H)mm

Operating Temperature: -25° C ~+55° C

Operating Humidity: 25~93% RH, non-coolant

Unlock PIN Code Memory: 100 sets

Unlock Fingerprint Memory: 100 sets

Unlock Card Memory: 100 sets

Supports Mechanical Key unlocking

Supports long-distance unlocking (optional) with purchase of online

component

Battery: 1.5VAA (LR6) alkaline batteries X4 (Operating Voltage: 4.5V~6V)

NAME OF PARTS

HOW TO USE

I Switch

Short press to enforce lock / Long press for default setting

I Switch

Volume Control

Choose 3 levels of volume

Volume Control

Emergency Power

Port

Card Reader

Smart Number Pad

Battery Cover

OPERATION DESCRIPTION

ADD USER PIN CODE

Add Master

PIN Code

Press S switch, enter initial master PIN code

when prompted by the voice guide (if it has been

changed, enter the changed master PIN code)

and press # followed by 1, 1. Enter the new PIN

code, and press # to confirm. Re-enter the new

PIN code and press # to save.

Add Normal

PIN Code

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 1, 2. Enter user code: 002~090, and

press # . Enter the normal user PIN code, and

press # to confirm. Re-enter the PIN code and

press # to save.

Add One-Time

PIN Code

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 1, 3. Enter user code: 091~0100, and

press # . Enter the One-Time PIN code, and press

# to confirm. Re-enter the One-Time PIN code

and press # to save.

Delete Single

PIN Code

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 1, 4. Enter user code: 002~100 and

press #. Successfully deleted.

Master PIN code cannot be deleted before the

default setting is restored.

Delete All

PIN Code

Press S switch, enter master PIN code when

prompted by the voice guide, and press # followed

by 1, 5, and press #. Successfully deleted.

Master PIN code cannot be deleted before the

default setting is restored.

Add Normal

Key Card

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 2, 1. Enter user code: 101~190 and

press #. Successfully added.

Add One-Time

Key Card

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 2, 2. Enter user code: 191~200 and

press #. Successfully added.

Delete Single

Key Card

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 2, 3. Enter user code: 101~200 and

press # to confirm. Press # again. Successfully

deleted.

Delete All

Key Card

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 2, 4 to confirm. Press # again.

Successfully deleted.

Add Master

Fingerprint

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 3, 1. Enter your fingerprint 3 times.

Successfully added. Re-enter if fail.

Add Normal

Fingerprint

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 3, 2. Enter user code: 202~290 and

press # to confirm. Enter your fingerprint 3 times.

Successfully added. Re-enter if fail.

Add SOS

Fingerprint

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 3, 3. Enter user code: 291~300 and

press # to confirm. Enter your fingerprint 3 times.

Successfully added. Re-enter if fail.

Delete Single

Fingerprint

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 3, 4. Enter user code: 202~300 and

press # to confirm. Press # again. Successfully

deleted.

Master fingerprint cannot be deleted before the

default setting is restored.

1 2 3

5 6

8 9

ADD USER FINGERPRINT

ADD USER KEY CARD

INITIALISATION AND RESTORE PROGRAM

Initialise User PIN Code: 1234567890

New changed password for 6 digits. “*” key as back. “#” key as confirm.

Master information included master PIN code and master fingerprint.

Restore Default Setting: Long press “I” switch for 5 seconds until you

hear the voice guide.

Include Handle

Speaker

Handle (Exterior)

Mechanical Key

S Switch - Short press for system menu /

Long press for normal mode

Volume Control

I Switch - Short press to

activate lock / Long press

for default settings

Sensor Bolt

Main Bolt

Two-Way

Bolt

Inner Body Handle

Child’s Lock

Emergency Unlock

Knob

Unlock Key (Inside)

S Switch

Short press for system menu / Long press for normal mode

S Switch

Fingerprint Reading Panel (Interior)

• User Manual

• Installation Guide

• Parts Pack

• 2 Card Keys

• 2 Mechanical Keys

Strike Plate

AA Alkaline Batteries

• 1 Smart Lock

Strike Box

OPENING THE DOOR

OPERATION DESCRIPTION

Unlock Mode Press S switch, enter master PIN code when

prompted by the voice guide, and press #.

Activate safe mode: Enter 5, 1, 1

Deactivate safe mode: Enter 5, 1, 2.

Change

Language

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

Chinese: Enter 5, 2, 1

English: Enter 5, 1, 2

Activate One

Touch Security

Press 2, 2, #

Deactivate One

Touch Security

Press 4, 4, # followed by master PIN code and

press #

Long Distance

Call *(optional

function)

Press 6, 6, #

Activate Force

Lock

Short press “I” key

Deactivate

Force Lock

Enter master information. Open the door for once.

Active Child's

Lock Press for 3-5 seconds to active the child’s lock

Deactivated

Child's Lock

1. Deactive by presssing the unlock buttom from inside

2. Press for 3-5 seconds again to deactive the

child’s lock.

Deactivate

Network

*(optional

function)

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 4, 2

Successfully deactivated.

SYSTEM SETTINGS

INSTANT FUNCTION SETTINGS

OPEN WITH PIN CODE

Touch the number pad >>> Enter your registered PIN code

>>> Press # to open door

OPEN WITH MECHANICAL KEY

TO REPLACE BATTERY

This product uses four 1.5V alkaline AA batteries. It is sustainable for 1

year if used 10 times a day. (Users are advised to use genuine alkaline

batteries.)

Make sure to replace all 4 batteries in the following manner:

* Upon hearing the low battery reminder;

* Using or replacing wrong type of batteries, which may cause

an explosion;

* Dispose of old batteries responsibly;

1.5V alkaline AA battery

ALARM AND USUAL FUNCTION

BREAK IN / DAMAGED ALARM

• Board anti-pry alarm: Alarm will go off when the front board is being

pried.

• Handle anti-pry alarm: System will lock down when the handle is

being pried.

• One touch security alarm: In single mode, alarm will go off when

someone is breaking the lock. In network mode, alarm will go off

when someone is breaking the lock and will be reported to the

terminal (network version requires the purchase of network

components separately).

• Key open sensor alarm: Alarm will go off when the mechanical key is

being used.

• Main bolt alarm: Alarm will go off when the main bolt is not locked.

• SOS alarm (only for network version): Both single mode and network

mode alarm will not go off, but will be reported to the terminal (network

version requires the purchase of network components separately).

3-MINUTE SYSTEM LOCK

• System will lock down for 3 minutes after 3 failed attempts. The

number pad will indicate the countdown time.

FORCE LOCK

• Short press I key and the voice guide will say “Force lock activated”.

Then you can use your master PIN code or master fingerprint or

mechanical key to unlock the door to which you will hear “Force lock

deactivated”.

IC CARD FEATURE REMINDER

• Other IC cards using the NFC feature may not function on other devices

once it is registered on Bosch Smart Lock.

SERVICE AND WARRANTY

• 24 hours hotline

• Genuine parts

• Lifetime service

• Extended warranty plan

PRODUCT STANDARD

This smart lock series is certified with the following national standards:

GA701-2007

General specifications for burglary-resistant fingerprint locks

GB21556-2008

General safety-technique requirements of locks

For more services and details, kindly call: +6014 3554 319

OPEN WITH FINGERPRINT

OPEN WITH EMERGENCY POWER SUPPLY

Connect with power bank

during emergency

Touch the number pad >>> Enter your registered PIN code

and press # OR enter registered card OR

scan your registered fingerprint

Tap registered card key

OPEN WITH CARD KEY

FRIENDLY REMINDER

In the event that your smart lock has malfunctioned, kindly contact your

reseller or customer service and provide the following information:

Address and contact number. Description of malfunction, purchase

date and received date, product model and product code. The

information above will help us serve you better and save you

unnecessary costs.

TERMS OF WARRANTY

The warranty service applies to manufacturing defects and regular-use

coverage only. It does not cover the following:

• Any damage caused by the user(s);

• Incorrect installation, testing and/or use other than instructed

by user manual;

• Unauthorized repair and/or modification to the product;

• Any accidental, misuse and/or intentional damages that

causes malfunction;

• Damage caused by acts of nature;

• Any loss and/or damage caused by the product’s environment

such as electricity, temperature, moisture, magnetic field

and/or any other unavoidable reasons.

• Any other reason except for product quality.

This product is under 3 (three) years warranty from the date of purchase

(as stated on the original receipt). The company provides free warranty

service for successful register user under the following terms:

Make sure to send your original purchase receipt or serial number

together with your product for our distributor. You are not entitled

to the warranty service should you fail to present the items

mentioned above.

You are not entitled to the warranty service should the purchase

receipt and/or serial number have been tampered with or altered

in any fashion.

WARRANTY AND SERVICES

PRODUCT WARRANTY CARD

SCAN the QR Code

SEND the following details:

(+6 014 355 4319)

Full Name (as per NRIC)

Email Address

Smart Lock Serial No. #

Please allow up to

3 working days for processing

and confirmation.

STEP 1

STEP 3

STEP 2

ATD LIFETECH CORPORATE SDN. BHD.

42A-1, Jalan OP 1/3, Pusat Perdagangan One Puchong,

Off Jalan Puchong 47160, Selangor

Contact:

+60 14 3694 914 (Sales)

+60 14 3554 319 (Helpline)

* (optional function) Network version requires the purchase of

network components separately.

Activate

Network

*(optional

function)

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 4, 1

Network requires the support of network

components. Refer to network components user

guide for details.

ADD NETWORK

Delete All

Fingerprint

Press S switch, enter master PIN code when

prompted by the voice guide, and press #

followed by 3, 5. Press #. Successfully deleted.

Master fingerprint cannot be deleted before the

default setting is restored.

ADD USER FINGERPRINT Enter the registered

fingerprint (Inside)

Key Hole

Use your mechanical key

when unable to use the door

lock. E.g. forgot PIN code /

electrical failure.

Andere Bosch Türschloss Handbücher

Bosch

Bosch ICP-EZM2 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung