Bosch 2 Bedienungsanleitung
Access Modular Controller 2
ADS‑AMC2‑4R4CF | APC‑AMC2‑4R4CF
en Guide d'installation
Access Modular Controller 2 Table of contents | en 3
Bosch Security Systems B.V. Guide d'installation 2022-11 | V04 |
Table of contents
1Safety 5
2Short information 7
3Introduction 8
3.1 Description 8
3.2 Product overview 10
3.2.1 Mainboard 10
3.2.2 Status display 12
3.3 System overview 13
4Installing 14
4.1 Mounting the device on a mounting rail 14
4.2 Unmounting the device from a mounting rail 14
4.3 Opening the case 15
4.4 Closing the case 16
4.5 Cabling 17
4.5.1 Conductor data for powering the controller 17
4.6 Grounding and shielding 18
4.6.1 Grounding for host interface 18
4.6.2 Grounding for extension interface 19
4.6.3 Grounding for bus interfaces 19
4.7 Connecting the power supply to the controller 20
4.8 Ethernet host interface 21
4.9 RS-485 host interface 22
4.9.1 RS-485 Two Wire Connection 23
4.9.2 RS-485 Four Wire Connection 23
4.9.3 DIP switch selector 23
4.10 RS-485 for extension modules 26
4.11 RS-485 interface for card readers 27
4.11.1 RS-485 data bus system conditions 27
4.11.2 Power reader 28
4.12 Connecting relay outputs 29
4.13 Connecting analog input devices 31
4.14 Tamper protection 33
5Operating 34
5.1 Configuring Ethernet interface 34
6UL requirements 35
6.1 System requirements 35
6.1.1 Computer 35
6.2 UL 294 level descriptions 35
6.3 Installation instructions 36
6.4 Extended technical specification 38
6.4.1 RS-485 extension 38
6.4.2 Power consumption 38
7Troubleshooting 39
7.1 Resetting the software 40
7.2 Resetting the device to factory default 41
8Service and repair 42
9Disposal 43
10 Technical specifications 44
4en | Table of contents Access Modular Controller 2
2022-11 | V04 | Guide d'installation Bosch Security Systems B.V.
11 Appendices 45
11.1 Connecting diagrams 45
11.2 Status display 48
11.2.1 Bootloader V00.49 48
11.2.2 Firmware until 6x.45, 37.60 49
11.2.3 Firrmware xx.61, 37.71 50
11.2.4 Firmware xx.62, 37.72 51
Access Modular Controller 2 Safety | en 5
Bosch Security Systems B.V. Guide d'installation 2022-11 | V04 |
1 Safety
!
Warning!
Read instructions
Before working with the device, read these instructions carefully. Make sure you have
understood all information described in this document.
!
Caution!
Fire hazard and risk of electric shock due to unauthorized spare parts and accessories
Unauthorized spare parts and accessories might lack grounding wires or other safety
elements. External power supplies must be installed by qualified personnel. The service
technician must use replacement parts or accessories that are specified by the manufacturer.
!
Warning!
Risk of explosion of lithium battery
The battery can explode if it is replaced incorrectly. Pay attention to the correct polarity when
inserting.
Replace only with the same battery type, as recommended by the manufacturer.
Do not overheat or expose to fire, mechanical force, or unusual high/low air pressure
conditions.
!
Warning!
Risk of physical injury due to blocked escape routes
This product may block escape routes if not installed correctly. To keep escape routes free:
- Use locks in fail-safe mode, so that doors can be released if power fails.
- Install manual override switches, such as break-glass or lever stations, to unlock doors in an
emergency.
i
Notice!
Dispose used batteries according to the battery manufacturer’s instructions, local laws and
regulations. Batteries must be disposed of separately from household waste.
i
Notice!
Device damage due to incorrect mounting
Mount this product on the matching mounting rails.
If the device falls or is damaged, check it before the installation.
i
Notice!
Considerations on local regulations
When you install the device, consider any local fire, health and safety regulations.
i
Notice!
Device damage due to electrostatic discharge
Protect the hardware from electrostatic discharge, especially when the device is open and
exposed. Always disconnect the controller from the power source before modifying the
installation. This product does not support hot plugging.
6en | Safety Access Modular Controller 2
2022-11 | V04 | Guide d'installation Bosch Security Systems B.V.
i
Notice!
Unauthorized access
If this product is installed in an unprotected environment, unauthorized people may be able
to enter.
Install the product in a location with restricted access.
This device is not suitable for use in locations where children may be present.
i
Notice!
Some features and functions described in this document depend on the firmware loaded into
the device and host software. Make sure that the controller is updated to the firmware
version provided with the host system.
This product is RoHS compliant. See Technical data for the full table of hazardous
components.
Access Modular Controller 2 Short information | en 7
Bosch Security Systems B.V. Guide d'installation 2022-11 | V04 |
2 Short information
The AMC2 can control a maximum of eight ID readers (depending on the reader type) and fully
processes the access logic at the assigned entrances.
The device controls a group of one to eight access points. These access points, also known as
entrances, can be:
– doors
– gates
– barriers
– turn stiles
– revolving doors
– mantraps
– ID card, PIN and biometric readers
– door opening elements
– sensors.
All the product versions use encrypted connections between the access modular controller
and the host system.
The controller stores all necessary information in a battery-buffered memory and in a compact
flash storage element. Even when the unit is offline, it is able to perform:
– Independent status and authorization checks on access points
– Take access decisions
– Activate and deactivate connected peripheral elements
– Detect and register all relevant events
The Access Modular Controller (AMC) is supported by the Access Professional Edition (APE),
BIS Access Engine (ACE) and the Access Management System (AMS).
For the latest information about our products, visit our online product catalog:
www.boschsecurity.com/xc/en/product-catalog/
Manufacturing dates
For product manufacturing dates, go to www.boschsecurity.com/datecodes/ and refer to the
serial number on the product label.
Remarks
This hardware is part of a security system.
Access should be granted to authorized people only.
Some states do not allow the exclusion or limitation of implied warranties, or limitation of
liability for incidental or consequential damages, hence the above limitation or exclusion might
not apply to you.
If you need further assistance or have any questions, contact:
Bosch Security Systems B.V.
Torenallee 49
5617 BA Eindhoven
Netherlands
www.boschsecurity.com
© Bosch Security Systems B.V., 2022
8en | Introduction Access Modular Controller 2
2022-11 | V04 | Guide d'installation Bosch Security Systems B.V.
3 Introduction
3.1 Description
Figure3.1: Access Modular Controller
Unsecured Area
Secured Area
Figure3.2: Example
The controller has four independent interfaces for RS-485 type readers. It can control a
maximum of four doors with a reader in each direction and a maximum of eight doors with a
reader in one direction only.
The electronics of the controller are completely covered by a plastic housing. The LCD (liquid
crystal display) provides all important status information.
All necessary information for access verification is stored in a battery buffered on-board
memory and a Compact Flash (CF) memory card. This guarantees autonomous access
decisions and complete access registrations even if the management host system is offline.
The built in compact flash adapter provides adequate storage capability for cardholders and
events.
The controller can communicate upstream to the host computer using one of the following
interfaces:
– Ethernet
– RS-485 multi-dropped, not supported by:
Access Modular Controller 2 Introduction | en 9
Bosch Security Systems B.V. Guide d'installation 2022-11 | V04 |
– BIS 4.9.1 and later
– AMS 4.0 and later.
The controller has eight analog input devices and eight relay outputs. With its analog input
devices, the controller verifies, for example, if a lock is closed or open. The relay outputs can
be used, for example, to activate lock mechanisms if access is granted, or activate the burglar
alarm system if an intrusion or system alert is detected. If the eight inputs and eight outputs
on the board are not enough to configure the system, up to three additional extension boards
can be connected. The extensions offer 8 or 16 additional inputs and outputs.
In the Bosch Access Host Systems, the setup procedure for a controller is made very simple
and fast by the use of door templates. Once selected, all the inputs and outputs are
predefined. These settings can be changed to choose every free contact of the controller or a
connected extension.
The product name and marking can be found on the backside of the product housing.
10 en | Introduction Access Modular Controller 2
2022-11 | V04 | Guide d'installation Bosch Security Systems B.V.
3.2 Product overview
3.2.1 Mainboard
1
7
3 4 52
10 11
89
6
Figure3.3: Upper circuit board with display (front)
1 DIP switch for RS-485 address and protocol selection.
2 Lithium battery for buffering of static RAM and real time clock (RTC). The battery life
is estimated at 10 years, nevertheless an error message is generated if the voltage
sinks below a preset minimum level.
NOTICE: In order to avoid an error message caused by an earlier voltage drop we
suggest to replace the battery every 8 years. Spare part: VARTA CR 2032 PCB.
3 Reset push button - reachable through the casing using a screwdriver
4 Liquid Crystal Display
5 Push button, available on top of the housing, to select different display modes
6 Jumper: Equalization of potential between different systems and earth ground
(shield)
7 Jumper: Interface selector RS-485 host connection, RS-485 two wire or RS-485 four
wire (depends on external wiring)
8 Configurable RS-485 host interface
9 Compact flash memory
10 Project-specific interface
11 Configurable 10/100 Mbit/s Ethernet host interface
Andere Handbücher für 2
11
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Bosch IP-Zugriffskontrollsysteme Handbücher
