Bosch NEI-Series Bedienungsanleitung

Dinion IP Infrared Imager

NEI-Series

en User Manual

Dinion IP Infrared Imager Table of Contents | en 3

Bosch Security Systems, Inc. User Manual F.01U.263.416 | 3.1 | 2012.09

Table of Contents

1Safety 7

1.1 Safety precautions 7

1.2 Important safety instructions 7

1.3 Important notices 8

1.4 FCC & ICES compliance 11

1.5 CSA certification - Disclaimer 12

1.6 Bosch notices 13

2 Description 14

2.1 Overview of Features 14

2.2 Unpacking 16

2.2.1 Parts Included with the Product 16

2.2.2 User-supplied Parts 16

2.2.3 Required Tools (User-Supplied) 17

3 Planning 18

3.1 Pre-installation Checklist 20

4 Installation 22

4.1 Overview of Installation Steps 22

4.2 Mount the Junction Box 23

4.3 Route Wires and Attach Connectors 24

4.3.1 About Alarm Output Connections 26

4.4 Attach Pendant Arm to Junction Box 27

5 Ethernet Connection (IP models) 28

5.1 About the Ethernet Connection 28

5.2 Connecting the NEI-30 to the PC 28

6 Manual Camera Settings 30

6.1 Adjusting Focus, Focal Length, Pan, and Tilt 30

6.1.1 Accessing the Rear Controls 30

6.1.2 Adjusting the Focus and Focal Length 31

6.1.3 Making Pan Adjustments 32

6.1.4 Making Tilt Adjustments 32

4en | Table of Contents Dinion IP Infrared Imager

F.01U.263.416 | 3.1 | 2012.09 User Manual Bosch Security Systems, Inc.

6.2 Adjusting Angle of LED Tilt and Width of Illumination Beam 33

6.2.1 Adjusting the Angle of LED Tilt 33

6.2.2 Adjusting the Illumination Beam Width 34

7 Operation via the Browser 36

7.1 System Requirements 36

7.2 Configuring the NEI-30 Camera 37

7.3 The LIVEPAGE 38

7.3.1 Digital I/O 38

7.3.2 System Log / Event Log 39

7.3.3 Saving Snapshots 39

7.3.4 Recording Video Sequences 40

7.4 Settings 40

8 Configuration via IP, Basic Mode 43

8.1 Basic Mode: Device Access 43

8.2 Basic Mode: Date/Time 44

8.3 Basic Mode: Network 45

8.4 Basic Mode: Encoder 46

8.5 Basic Mode: Recording 46

8.6 Basic Mode: System Overview 47

9 Configuration via IP, Advanced Mode 48

9.1 Advanced Mode: General 48

9.1.1 Identification 48

9.1.2 Password 49

9.1.3 Date/Time 50

9.1.4 Display Stamping 51

9.2 Advanced Mode: Web Interface 53

9.2.1 Appearance 53

9.2.2 LIVEPAGE Functions 54

9.2.3 Logging 55

9.3 Advanced Mode: Camera 56

9.3.1 Picture Settings: Mode 56

9.3.2 Picture Settings: ALC 57

9.3.3 Picture Settings: Shutter/AGC 57

9.3.4 Picture Settings: Day/Night 58

Dinion IP Infrared Imager Table of Contents | en 5

Bosch Security Systems, Inc. User Manual F.01U.263.416 | 3.1 | 2012.09

9.3.5 Picture Settings: Iluminator 59

9.3.6 Picture Settings: Enhance 60

9.3.7 Picture Settings: Color 60

9.3.8 Encoder Profile 61

9.3.9 Encoder Streams 64

9.3.10 Privacy Masks 65

9.3.11 Installer Menu 66

9.4 Advanced Mode: Recording 67

9.4.1 Storage Management 67

9.4.2 Recording Profiles 69

9.4.3 Retention Time 72

9.4.4 Recording Scheduler 72

9.4.5 Recording Status 74

9.5 Advanced Mode: Alarm 74

9.5.1 Alarm Connections 74

9.5.2 VCA 77

9.5.3 Alarm E-Mail 84

9.5.4 Alarm Task Editor 85

9.6 Advanced Mode: Interfaces 86

9.6.1 Relay 86

9.7 Advanced Mode: Network 87

9.7.1 Network Access 87

9.7.2 Advanced 90

9.7.3 Multicast 92

9.7.4 FTP Posting 94

9.7.5 Encryption 95

9.8 Advanced Mode: Service 95

9.8.1 Maintenance 95

9.8.2 Licenses 97

9.8.3 System Overview 97

10 Operation via Keyboard and OSD Menus 98

10.1 Menus 98

10.1.1 Top level menus 98

10.1.2 Menu navigation 98

10.2 Pre-defined modes 99

10.3 Main menu structure 101

6en | Table of Contents Dinion IP Infrared Imager

F.01U.263.416 | 3.1 | 2012.09 User Manual Bosch Security Systems, Inc.

10.3.1 Mode submenu 101

10.3.2 ALC submenu 102

10.3.3 Shutter/AGC submenu 103

10.3.4 Day/Night submenu 105

10.3.5 Illuminator submenu 106

10.3.6 Enhance / Dynamic Engine submenu 107

10.3.7 Color submenu 108

10.3.8 VMD submenu 109

10.4 Install menu structure 110

10.4.1 Lens Wizard submenu 110

10.4.2 Language submenu 111

10.4.3 Privacy Masking submenu 111

10.4.4 Synchronization submenu 112

10.4.5 Alarm Output submenu 112

10.4.6 Connections submenu 113

10.4.7 Test Signals submenu 113

10.4.8 Camera ID submenu 114

10.4.9 Defaults submenu 114

11 Maintenance 115

11.1 Repairs 115

11.2 Transfer and Disposal 115

12 Technical Data 116

Index 118

Dinion IP Infrared Imager Safety | en 7

Bosch Security Systems, Inc. User Manual F.01U.263.416 | 3.1 | 2012.09

1Safety

1.1 Safety precautions

1.2 Important safety instructions

Read, follow, and retain all of the following safety instructions.

Heed all warnings on the unit and in the operating instructions

before operating the unit.

1. Clean only with dry cloth.

2. Do not block any ventilation openings. Install in

accordance with manufacturer’s instructions.

3. Do not install near any heat sources such as radiators, heat

registers, stoves or other apparatus (including amplifiers)

that produce heat.

DANGER!

High risk: This symbol indicates an imminently hazardous

situation such as “Dangerous Voltage” inside the product.

If not avoided, this will result in an electrical shock, serious

bodily injury, or death.

WARNING!

Medium risk: Indicates a potentially hazardous situation.

If not avoided, this could result in minor or moderate bodily

injury.

CAUTION!

Low risk: Indicates a potentially hazardous situation.

If not avoided, this could result in property damage or risk of

damage to the unit.

NOTICE!

This symbol indicates information or a company policy that

relates directly or indirectly to the safety of personnel or

protection of property.

8en | Safety Dinion IP Infrared Imager

F.01U.263.416 | 3.1 | 2012.09 User Manual Bosch Security Systems, Inc.

4. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

power where they exit from the apparatus.

5. Use only attachments/accessories specified by the

manufacturer.

6. Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in a

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus,

does not operate normally, or has dropped. When

servicing, power shall be disconnected.

1.3 Important notices

All-pole power switch - Incorporate an all-pole power switch,

with a contact separation of at least 3 mm in each pole, into the

electrical installation of the building. If it is needed to open the

housing for servicing and/or other activities, use this all-pole

switch as the main disconnect device for switching off the

voltage to the unit.

Camera signal - Protect the cable with a primary protector if

the camera signal is beyond 140 feet, in accordance with

NEC800 (CEC Section 60).

Accessories - Do not place this unit on an

unstable stand, tripod, bracket, or mount. The

unit may fall, causing serious injury and/or

serious damage to the unit. Use only with the

cart, stand, tripod, bracket, or table specified by

the manufacturer. When a cart is used, use

caution and care when moving the cart/

apparatus combination to avoid injury from tip-

over. Quick stops, excessive force, or uneven

surfaces may cause the cart/unit combination to

overturn. Mount the unit per the manufacturer's

instructions.

Dinion IP Infrared Imager Safety | en 9

Bosch Security Systems, Inc. User Manual F.01U.263.416 | 3.1 | 2012.09

Coax grounding:

– Ground the cable system if connecting an outside cable

system to the unit.

– Connect outdoor equipment to the unit's inputs only after

this unit has had its grounding plug connected to a

grounded outlet or its ground terminal is properly

connected to a ground source.

– Disconnect the unit's input connectors from outdoor

equipment before disconnecting the grounding plug or

grounding terminal.

– Follow proper safety precautions such as grounding for

any outdoor device connected to this unit.

CAUTION!

This product has been tested according to standard CIE/IEC

62471:2006 “Photobiological safety of lamps and lamp

systems” and found to meet Risk Group 2 for exposure limit

4.3.7 “Infrared radiation hazard exposure limits for the eye.”

For other hazard exposure limits, the product was found to be

exempt. Risk Group 2 is characterized in the standard as

“products generally do not pose a realistic optical hazard if

aversion responses limit the exposure duration or where

lengthy exposures are unrealistic.” Since there is no aversion

response for IR, avoid eye exposure. Risk Group 2 sources do

not pose an infrared radiation hazard for the eye within 10 s at

distances beyond 200 mm or 8 inches. The Exposure Hazard

Value for the product (ratio of the Exposure level to the

Exposure limit) is up to 10 at a test distance of 200 mm (8

inches). The Hazard Distance (distance beyond which the

product falls into the exempt/safe group) is at most 640 mm

(25 inches). Note that typical use cases are well beyond the

Hazard Distance.When servicing the unit, physically disconnect

the power supply to avoid possible IR exposure to the eyes. If

physical disconnection is not possible, use appropriate

shielding to block the LED panel or use eye protection with a

transmission of 10% or less at a wavelength of 850 nm.

10 en | Safety Dinion IP Infrared Imager

F.01U.263.416 | 3.1 | 2012.09 User Manual Bosch Security Systems, Inc.

U.S.A. models only - Section 810 of the National Electrical Code,

ANSI/NFPA No.70, provides information regarding proper

grounding of the mount and supporting structure, grounding of

the coax to a discharge unit, size of grounding conductors,

location of discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

Electronic Surveillance - This device is intended for use in

public areas only. U.S. federal law strictly prohibits

surreptitious recording of oral communications.

Environmental statement - Bosch has a strong commitment

towards the environment. This unit has been designed to

respect the environment as much as possible.

Fuse rating - For protection of the device, the branch circuit

protection must be secured with a maximum fuse rating of 16A.

This must be in accordance with NEC800 (CEC Section 60).

Moving - Disconnect the power before moving the unit. Move

the unit with care. Excessive force or shock may damage the

unit and the hard disk drives.

Outdoor signals - The installation for outdoor signals, especially

regarding clearance from power and lightning conductors and

transient protection, must be in accordance with NEC725 and

NEC800 (CEC Rule 16-224 and CEC Section 60).

Permanently connected equipment - Incorporate a readily

accessible disconnect device external to the equipment.

Disposal - Your Bosch product was developed

and manufactured with high-quality material and

components that can be recycled and reused.

This symbol means that electronic and electrical

appliances, which have reached the end of their

working life, must be collected and disposed of

separately from household waste material.

Separate collecting systems are usually in place

for disused electronic and electrical products.

Please dispose of these units at an

environmentally compatible recycling facility,

per European Directive 2002/96/EC.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bosch Sicherheitskamera Handbücher

Bosch

Bosch AUTODOME IP starlight 5000i Bedienungsanleitung

Bosch

Bosch NDE-8503-R Bedienungsanleitung

Bosch

Bosch LTC 7935 Bedienungsanleitung

Bosch

Bosch VG4-522-ECS0WF Bedienungsanleitung

Bosch

Bosch LTC 0455 Series Handbuch

Bosch

Bosch WZ18NV312-0 Bedienungsanleitung

Bosch

Bosch AN traffic 4000 IR Bedienungsanleitung

Bosch

Bosch AN bullet 2000 IR Bedienungsanleitung

Bosch

Bosch VDC-230 Bedienungsanleitung

Bosch

Bosch MIC IP dynamic 7000 HD Bedienungsanleitung

Bosch

Bosch FLEXIDOME corner 9000 MP Montageanleitung

Bosch

Bosch VKC 4075 Bedienungsanleitung

Bosch

Bosch NWD-455V03-20P Bedienungsanleitung

Bosch

Bosch BasicDome Series Bedienungsanleitung

Bosch

Bosch DINION IP imager 9000 HD Bedienungsanleitung

Bosch

Bosch VG5-7230-CPT5 Bedienungsanleitung

Bosch

Bosch Autodome Inteox 7000i-2MP Bedienungsanleitung

Bosch

Bosch AUTODOME IP 4000 HD NEZ-4 series Bedienungsanleitung

Bosch

Bosch VG4-200 Series Bedienungsanleitung

Bosch

Bosch VG4-322-ECS0WF Bedienungsanleitung

Bosch

Bosch VG4 Series Bedienungsanleitung

Bosch

Bosch DINION IP 5000 HD Betriebsanleitung

Bosch

Bosch NWD-455 FlexiDome Bedienungsanleitung

Bosch

Bosch VEZ Series Leitfaden

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung