Bosch REG-X Bedienungsanleitung
INSTALLATION
INSTRUCTIONS
REG-X
2
MAN-REG-X-07
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep this instruction.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with manufacturer instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce
heat.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong is provided for your safety. If the provided
3
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the power where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in a way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
4
IMPORTANT
For best results, please read this Instruction Booklet prior
to installing the REG-X camera.
WARNING !
CSA Certified / UL Listed CLASS 2 power adaptors must
be used in order to comply with electrical safety standards.
Bosch Security Systems, Inc. will not be responsible for
injuries or damages resulting from the
improper installation or use of any product
sold by Bosch Security Systems, Inc their agents,
distributors or dealers.
EU Directives covered by this declaration:
72/9/EC Low Voltage Directives
89/336/EEC Electromagnetic Compatibility Directive
5
NOTE: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. As part of it's normal operation this
device can generate radio frequency energy and if not
installed and used in accordance with the installation
manual may cause interference to radio communications.
However, there is no guarantee that interference will not
occur on a particular installation. If the device does cause
interference to radio or television reception the user is
encouraged to try to correct the interference by one or
more of the following measures:
1) Fit Ferrite beads on all cable to and from the power
supply box, within the box walls.
2) Route the composite cable between the camera and the
power supply in steel conduit piping over the entire run of
the cable up to and including connection to a deep conduit
base fitted under the camera and a conduit fitting adaptor
in the wall of the PSU box.
3) Contact BOSCH Service Center for further advice.
6
INDEX – REG-X Camera
Description………………………………………………...7
Unpacking………………………………………………....8
Parts List…………………………………………………..8
Items Required for Installation…………………………..8
Initial Preparations………………………………………..9
Guidelines………………………………………………....9
1. Mechanical Specifications REG-X…………..…….10
2. Input Power / Video Output Connections…………11
3. Mounting Specification………..……………………12
4. Camera Adjustment………………………………...16
5. Troubleshooting Guide…...………………….……..17
6. General specifications…………..………….………20
7
DESCRIPTION
The REG-X license plate capture camera unit consists of
one IR-sensitive monochrome camera and one integrated
panel of Infrared LEDs. The license plate capture camera
produces optimum license plate images during day and
night settings in all-weather conditions. The camera has
technology that helps block out unwanted light such as
headlamps or sunlight, thus ensuring no bloomed-out or
washed-out images of the license plates.
The REG-X camera you have purchased is designed and
configured to capture images of license plates under a
wide range of ambient light and weather conditions.
The all-weather housing with a covert acrylic window
contains all the electronics. Low voltage operation, low
power consumption, LED illuminator, and solid-state CCD
technology make this camera very reliable and efficient.
A voltage regulator circuit allows for DC or AC operation
between 12 and 24 VAC/VDC.
See the Light. Get the Picture.®
8
UNPACKING
Care should be taken when unpacking the shipped unit.
Check the parts list and confirm all items have been
located. Inspect the equipment thoroughly to ensure
nothing was damaged in transit.
Contact BOSCH Service Center if a problem is noted,
see the rear page of this booklet for contact numbers.
PARTS LIST (items supplied with unit)
-REG-X camera assembly
-Adjustment hex key
-Installation Instructions booklet
ITEMS REQUIRED FOR INSTALLATION
(not supplied with units)
•Mounting hardware
•Mounting tools
•Proper power supply
9
INITIAL PREPARATIONS
•Determine the operating voltage at the
installation site. The camera‘s Voltage Regulator
Board accepts both 12-24VDC and VAC input
without change to internal connections.
See Section 2, Input Power/Video Output
Connections.
•Determine the optimum location for the camera.
See Section 3, Mounting Specification.
•All cameras have been tested prior to shipment.
To verify the camera is operational when
connected to a power supply and monitor, a
retro reflective license plate should be placed in
view of the camera to see a license plate image
otherwise the image may appear dark or black.
Note: The camera has been optimized to capture
vehicle license plates of moving vehicles under all
lighting conditions.
GUIDELINES
The installation of the REG-X camera is explained in
Sections 1 to 3.
It is important that these steps are followed and practice
proper installation procedures with proper safety
equipment.
10
1. MECHANICAL SPECIFICATIONS – REG X
(See Section 6 - General Specifications, for more information)
Front View Side View
Bottom View
Showing mounting holes
*Optional mounting kit is available to mount the camera onto an
electrical box; Part Number: WZMB.001
Figure 1 - General Mechanical Specifications
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Bosch Sicherheitskamera Handbücher
Bosch
Bosch VDN-5085 Bedienungsanleitung
Bosch
Bosch AutoDome VG5-825-ECEV Bedienungsanleitung
Bosch
Bosch FlexiDomeVF VDM-345V03-20 Bedienungsanleitung
Bosch
Bosch VG5 100 Series Bedienungsanleitung
Bosch
Bosch AutoDome 100 Series Bedienungsanleitung
Bosch
Bosch EX70MNX804-N Bedienungsanleitung
Bosch
Bosch FLEXIDOME IP micro 3000i-outdoor Bedienungsanleitung
Bosch
Bosch LTC 1312/20 FlexiDome I Bedienungsanleitung
Bosch
Bosch LTC 0x35 Series Bedienungsanleitung
Bosch
Bosch VOT-320 Bedienungsanleitung
Bosch
Bosch SVI-1609-5 Montageanleitung
Bosch
Bosch AUTODOME IP starlight 5000i Bedienungsanleitung
Bosch
Bosch VDN-498V03-11 Installationsanleitung
Bosch
Bosch BasicDome Series Bedienungsanleitung
Bosch
Bosch SVI-1609-5 Bedienungsanleitung
Bosch
Bosch MIC Series 550 Bedienungsanleitung
Bosch
Bosch DINION IP starlight 7000 HD Bedienungsanleitung
Bosch
Bosch MIC IP fusion 9000i Bedienungsanleitung
Bosch
Bosch DINION IP 5000 HD Betriebsanleitung
Bosch
Bosch VG4-322-ECS0WF Bedienungsanleitung
