Bosch VEZ-221-ECCE Bedienungsanleitung

AutoDome Easy II IP

VEZ Series

en Installation Manual

AutoDome Easy II IP Table of Contents | en 3

Bosch Security Systems, Inc. Installation Manual F.01U.164.576 | 2.0 | 2010.03

Table of Contents

1Safety 7

1.1 Important Safety Instructions 7

1.2 Safety Precautions 10

1.3 Important Notices 10

1.4 Customer Support and Service 17

2 Unpacking 18

2.1 Parts List 18

2.2 Safety Rules 19

3 Description 20

4 Installing a Surface Mount 22

4.1 Description 22

4.1.1 Additional Tools Required 23

4.1.2 Preparing the Surface Mount for an Indoor Installation 23

4.1.3 Preparing the Surface Mount for an Outdoor Installation 25

4.1.4 Installing the Camera to the Mounting Plate 29

5 Installing a Wall Mount 33

5.1 Description 33

5.1.1 Additional Tools Required 34

5.1.2 Preparing the Wall Mount for an Indoor Installation 34

5.1.3 Preparing the Wall Mount for an Outdoor Installation 36

5.1.4 Installing the Camera to the Mounting Plate 40

6 Installing a Recessed Mount 44

6.1 Description 44

6.1.1 Additional Requirements 44

6.1.2 Preparing the Ceiling for Installation 45

6.1.3 Installing the Camera to the Mounting Plate 48

4en | Table of Contents AutoDome Easy II IP

F.01U.164.576 | 2.0 | 2010.03 Installation Manual Bosch Security Systems, Inc.

7 Installing a Pipe Mount 52

7.1 Description 52

7.1.1 Tools/Supplies Required 53

7.1.2 Preparing the Ceiling for Installation 53

7.1.3 Installing the Camera to the Mounting Plate 60

8 Preparing the Wiring 63

8.1 Power 63

8.2 Connecting the Power 64

8.2.1 Power Connections to Indoor Cameras 65

8.2.2 Power Connections to Outdoor Cameras 66

8.2.3 Power Connections to Heater (all outdoor models) 67

8.3 Ethernet Connection (IP models) 67

9 Alarms and Relay Connections 69

9.1 Alarm Input 69

9.2 Connecting Alarms (inputs 1 through 2) 70

9.2.1 Connecting a Normally Open Alarm 70

9.2.2 Connecting a Normally Closed Alarm 71

9.3 Alarm Outputs 72

9.3.1 Connecting an Open Collector Output 72

10 Getting Started 73

10.1 Powering On 73

11 Using the AutoDome Easy II IP 74

11.1 Overview of Features 75

11.2 System Requirements 76

11.3 Connecting the AutoDome Easy II IP to the PC 77

11.4 Configuring the AutoDome Easy II IP Camera 78

11.5 The LIVEPAGE 79

11.5.1 Entering a Keyboard Control Command 82

11.6 Saving Snapshots 85

11.7 Recording Video Sequences 85

AutoDome Easy II IP Table of Contents | en 5

Bosch Security Systems, Inc. Installation Manual F.01U.164.576 | 2.0 | 2010.03

12 Configuring the AutoDome Easy II IP 86

12.1 Basic Mode: Device Access 87

12.2 Basic Mode: Date/Time 88

12.3 Basic Mode: Network 89

12.4 Basic Mode: Encoder Profile 90

12.5 Basic Mode: Recording 91

12.6 Basic Mode: System Overview 91

13 On-Screen Display Menu Navigation 92

13.1 Setup Menu 92

13.2 Camera Setup Menu 94

13.3 Lens Setup 97

13.4 PTZ Setup Menu 99

13.5 Display Setup Menu 102

13.5.1 Specifying a Shot or a Sector Title 105

13.6 Communication Setup Menu 106

13.7 Alarm I/O Setup 108

13.8 Alarm I/O Rule Setup Menu 111

13.9 Language Menu 114

13.10 Diagnostics Menu 115

14 Common User Commands (unlocked) 118

14.1 Setting AutoPan Mode 118

14.2 Setting Preset Shots 119

14.3 Configuring Preposition Tours 119

14.4 Programming the Inactivity Operation 120

14.5 Recorded Tours 120

6en | Table of Contents AutoDome Easy II IP

F.01U.164.576 | 2.0 | 2010.03 Installation Manual Bosch Security Systems, Inc.

15 Keyboard Commands by Number 122

16 Preventive Maintenance 127

17 Troubleshooting 128

17.1 AutoDome Easy II IP Operation and Control 129

18 BVIP Firmware Updates 132

18.1 Upgrading the AutoDome Easy II IP 132

18.2 Beginning the Firmware Update Process 132

Index 134

AutoDome Easy II IP Safety | en 7

Bosch Security Systems, Inc. Installation Manual F.01U.164.576 | 2.0 | 2010.03

1Safety

1.1 Important Safety Instructions

Read, follow, and retain for future reference all of the following

safety instructions. Heed all warnings on the unit and in the

operating instructions before operating the unit.

1. Cleaning - Unplug the unit from the outlet before cleaning.

Follow any instructions provided with the unit. It is

generally sufficient to use a dry cloth for cleaning, but a

moist lint-free cloth or leather shammy may also be used.

Do not use liquid cleaners or aerosol cleaners.

2. Heat sources - Do not install the unit near any heat

sources such as radiators, heaters, stoves, or other devices

(including amplifiers) that produce heat.

3. Ventilation - Any openings in the unit housing are provided

for ventilation to prevent overheating and ensure reliable

operation. Do not block or cover these openings. Do not

place the unit in an enclosure unless proper ventilation is

provided, or the manufacturer's instructions have been

adhered to.

4. Water - Do not use this unit near water, for example near a

bathtub, washbowl, sink, laundry basket, in a damp or wet

basement, near a swimming pool, or in any area classified

as a wet location. To reduce the risk of fire or electrical

shock, do not expose this unit to rain or moisture.

5. Object and liquid entry - Never push objects of any kind

into this unit through openings, as they may touch

dangerous voltage points or short out parts, which could

result in a fire or electrical shock. Never spill liquid of any

kind on the unit. Do not place objects filled with liquids,

such as vases or cups, on the unit.

6. Lightning - For added protection during a lightning storm,

or when leaving this unit unattended and unused for long

periods, unplug the unit from the wall outlet and

disconnect the cable system. This will prevent damage to

the unit from lightning and power line surges.

8en | Safety AutoDome Easy II IP

F.01U.164.576 | 2.0 | 2010.03 Installation Manual Bosch Security Systems, Inc.

7. Control adjustment - Adjust only those controls specified

in the operating instructions. Improper adjustment of

other controls may cause damage to the unit. Use of

controls or adjustments, or performance of procedures

other than those specified, may result in hazardous

radiation exposure.

8. Overloading - Do not overload outlets and extension cords.

This can cause fire or electrical shock.

9. Power disconnect - Units with or without ON/OFF

switches have power supplied whenever the power cord is

inserted into the power source; however, the unit is

operational only when the ON/OFF switch is in the ON

position. The power cord is the main power disconnect

device for switching off the voltage for all units.

10. Power sources - Operate the unit only via the type of

power source indicated on the label. Before proceeding,

be sure to disconnect the power from the cable being

connected to the unit.

– For battery powered units, refer to the operating

instructions.

– For units supplied by an external power source, use

only the recommended or approved power supplies.

– For limited power source units, this power source

must comply with EN60950. Substitutions may

damage the unit or cause fire or shock.

– For 24 VAC units, voltage applied to the unit's power

input should not exceed +/- 10% or 21.6-26.4 VAC.

User-supplied wiring must comply with local electrical

codes (Class 2 power levels). Do not ground the

supply at the terminals or at the unit's power supply

terminals.

– If unsure of the type of power supply to use, contact

your dealer or local power company.

11. Servicing - Do not attempt to service this unit yourself.

Opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

AutoDome Easy II IP Safety | en 9

Bosch Security Systems, Inc. Installation Manual F.01U.164.576 | 2.0 | 2010.03

12. Damage requiring service - Unplug the unit from the main

AC power source and refer servicing to qualified service

personnel when any damage to the equipment has

occurred, for example if:

– the power supply cord or plug is damaged

– exposure to moisture, water, and/or inclement

weather (rain, snow etc.)

– liquid has been spilled in or on the equipment

– an object has fallen into the unit

– the unit has been dropped or the unit cabinet is

damaged

– the unit exhibits a distinct change in performance

– the unit does not operate normally when the user

correctly follows the operating instructions.

13. Replacement parts - Be sure the service technician uses

replacement parts specified by the manufacturer, or that

they have the same characteristics as the original parts.

Unauthorized substitutions may cause fire, electrical

shock, or other hazards.

14. Safety check - Safety checks should be performed on

completion of service or repairs to the unit, to ensure that

the unit is in proper operating condition.

15. Installation - Install in accordance with the manufacturer's

instructions and in accordance with applicable local codes.

16. Attachments, changes, or modifications - Only use

attachments/accessories specified by the manufacturer.

Any change to or modification of the equipment not

expressly approved by Bosch could void the warranty or, in

the case of an authorization agreement, authority to

operate the equipment.

10 en | Safety AutoDome Easy II IP

F.01U.164.576 | 2.0 | 2010.03 Installation Manual Bosch Security Systems, Inc.

1.2 Safety Precautions

1.3 Important Notices

Accessories - Do not place this unit on an unstable stand,

tripod, bracket, or mount. The unit may fall, causing serious

injury to persons and/or severe damage to the unit. Use only

with the cart, stand, tripod, bracket, or table specified by the

manufacturer. When a cart is used, exercise caution and care

when moving the cart/apparatus combination to avoid tipping it

over, which could result in injury. Quick stops, excessive force,

or uneven surfaces may cause the cart/unit combination to

overturn. Mount the unit in line with the manufacturer's

instructions.

All-pole power switch - Incorporate an all-pole power switch,

with a contact separation of at least 3 mm in each pole, into the

electrical installation of the building. If it is needed to open the

housing for servicing and/or other activities, use this all-pole

DANGER!

This symbol indicates an imminently hazardous situation such

as “Dangerous Voltage” inside the product. If not avoided, this

will result in an electrical shock, serious bodily injury, or death.

WARNING!

Indicates a potentially hazardous situation. If not avoided, this

may result in minor or moderate injury. Alerts the user to

important instructions accompanying the unit.

CAUTION!

Indicates a potentially hazardous situation. If not avoided, this

may result in damage to property or risk of damage to the unit.

NOTICE!

This symbol indicates information or a company policy that

relates directly or indirectly to the safety of personnel or

protection of property.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bosch Sicherheitskamera Handbücher

Bosch

Bosch FlexiDome NDC-455V03-21PS Bedienungsanleitung

Bosch

Bosch DINION 5100i IR Bedienungsanleitung

Bosch

Bosch WZ18NV312-0 Bedienungsanleitung

Bosch

Bosch Junior Installationsanleitung

Bosch

Bosch AUTODOME IP starlight 5000i Bedienungsanleitung

Bosch

Bosch VJR SERIES Bedienungsanleitung

Bosch

Bosch AN traffic 4000 IR Bedienungsanleitung

Bosch

Bosch LTC0485/11 Bedienungsanleitung

Bosch

Bosch VKC 4075 Bedienungsanleitung

Bosch

Bosch FLEXIDOME HD VR Gebrauchsanweisung

Bosch

Bosch DINION IP thermal 8000 Bedienungsanleitung

Bosch

Bosch KBE-498V28-20 Bedienungsanleitung

Bosch

Bosch EX14 Series Bedienungsanleitung

Bosch

Bosch FlexiDome NDN-832 Bedienungsanleitung

Bosch

Bosch FCS-8000-VFD-B Bedienungsanleitung

Bosch

Bosch LTC 7490 Bedienungsanleitung

Bosch

Bosch VG4 Series Bedienungsanleitung

Bosch

Bosch MIC412 Bedienungsanleitung

Bosch

Bosch VDC?480 Series Bedienungsanleitung

Bosch

Bosch VBC?265 Series Bedienungsanleitung

Bosch

Bosch MIC Series 500 Bedienungsanleitung

Bosch

Bosch VC973650T Bedienungsanleitung

Bosch

Bosch EXTEGRA IP 9000 FX Bedienungsanleitung

Bosch

Bosch F01U316304 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung