Bosch FCP-O 500 Bedienungsanleitung

Conventional Automatic Detectors

FCP‑O 500 | FCP‑OC 500 | FCP‑O 500‑P | FCP‑OC 500‑P

en Operation Guide

Conventional Automatic Detectors Table of contents | en 3

Bosch Sicherheitssysteme GmbH Operation Guide 2019.11 | 5.0 | F.01U.003.962

Table of contents

1Product Description 4

1.1 Performance Features 6

1.2 System Description 6

1.3 Configuration of the Detector 7

1.4 Functional Description of the Sensor Technology 7

1.5 LED Operation 8

2Planning Notes 9

3Installation 10

3.1 Ceiling Mount Back Box 10

3.2 Detector Base/Detector Base with EOL Resistor 11

3.3 Detector and Trim Ring 15

3.4 Built-in Housing for Concrete Ceilings 16

3.5 Surface Mount Back Box 16

3.6 Remote indicators 17

4Maintenance and Service 21

4.1 General Notes for Detector Testing 22

4.2 Inspection Procedure for FCP‑OC 500 22

4.3 Inspection Procedure for FCP‑O 500 23

4.4 Reading the Contamination Level 23

4.5 Electronic Function Test (Optional) 24

4.6 Repair 24

4.7 Disposal 24

5Technical Data 25

5.1 Detector and Trim Ring 25

5.2 Detector Base 26

5.3 Mounting Boxes 26

5.4 Remote indicator 27

6Appendix 29

6.1 Abbreviations 29

6.2 Order Overview 29

6.2.1 Detector and Trim Ring 29

6.2.2 Detector bases / Remote indicators 30

6.2.3 Mounting Boxes 31

6.2.4 Service tools/accessories 31

4en | Product Description Conventional Automatic Detectors

2019.11 | 5.0 | F.01U.003.962 Operation Guide Bosch Sicherheitssysteme GmbH

1 Product Description

Figure1.1: 500 Series Fire Detector

With their low profile design, flush‑mounted installation and possibilities for color toning, the

fire detectors in the 500 series open up a new dimension with respect to aesthetic and

functional demands.

The cooperation of engineers and designers has created the timeless, innovative design of this

detector, which integrates pleasantly into the ceiling. The detectors with associated trim ring

are available in the versions white and transparent with color toning inserts. Through the use

of the supplied color toning inserts, optimum adjustment to many different environments

becomes possible.

The lack of an optical labyrinth and their easily-cleaned smooth surface means the detectors

are also suitable for applications in high-dust areas.

The low profile, flush-mounted design allows the use the detectors even in areas that must be

free of protrusions.

Thanks to the geometric arrangement of two separate optical sensor systems, the detectors

are not sensitive to interference, such as that caused by insects. The scattered light volume

that is evaluated by the sensors is located in the free space a few centimeters below the

ceiling.

The contamination level is measured constantly. Contamination of the detector surface leads

to an active adjustment of the threshold (drift compensation).

The detector is available as a scattered light fire detector only or as a multisensor detector

with an additional gas sensor.

The combination of scattered light detector and gas sensor allows the evaluation of signals

with the help of modern signal processing methods. The result is high immunity against

deceptive alarms and extended application possibilities in environments that are not suitable

for pure scattered light smoke detectors.

The FCP‑500 series are conventional technology detectors. Due to their current consumption,

a four-wire connection is required. Thus, they can be operated with numerous different fire

panels.

Conventional Automatic Detectors Product Description | en 5

Bosch Sicherheitssysteme GmbH Operation Guide 2019.11 | 5.0 | F.01U.003.962

Accessories

The 500 Series Detectors are generally mounted flush with the ceiling in false ceilings. The

detector and base are installed in a robust ceiling mount back box. In addition, a housing for

mounting within concrete ceilings can be used.

For special applications where recessed ceiling mounting is not possible, a surface mount

back box is available. This is used as an alternative to the ceiling mount back box.

The surface mount back box with damp room seal also allows the detector to be used in a

humid environment.

All bases have an integrated strain relief for false ceiling cables.

The connection terminals are easily accessible. Cables up to 3.3 mm2 in cross section can be

used.

An innovative concept for locking the detector module utilizing the push‑in/push‑out principle

allows very quick and easy insertion and exchange of the click and lock detector.

For the detector test and detector exchange, a special user-friendly service accessory is

available.

Overview of the 500 Series Conventional Detectors and Accessories

FCP-O 500-P

FCP-OC 500-P

FAA-500-BB FAA-500-CB

FAA-500-SB-H

FAA-500-TR-W

FAA-500-TR-P

FCP-O 500

FCP-OC 500

FCA-500-EU

FCA-500-E-EU

Figure1.2: 500 Series Detectors and Accessories

Conventional Detectors:

- FCP-O 500 Conventional Optical Fire Detector, white

- FCP-O 500-P Conventional Optical Fire Detector, transparent with color toning inserts

- FCP-OC 500 Conventional Multisensor Fire Detector, optical/chemical, white

- FCP-OC 500-P Conventional Multisensor Fire Detector, optical/chemical, transparent

with color toning inserts

- FAA-500-TR-W White Trim Ring for detectors 500 and 520Series

- FAA-500-TR-P Transparent Trim Ring with color toning inserts for detectors 500 and

520Series

Conventional Detector Bases:

- FCA-500-EU Conventional Detector Base

6en | Product Description Conventional Automatic Detectors

2019.11 | 5.0 | F.01U.003.962 Operation Guide Bosch Sicherheitssysteme GmbH

- FCA-500-E-EU Conventional Detector Base with EOL resistor

Mounting Boxes:

- FAA-500-BB Ceiling Mount Back Box

- FAA-500-CB Built-in Housing for concrete ceilings

- FAA-500-SB-H Surface Mount Back Box with damp room seal

Service Accessories:

- FAA-500-RTL Detector Exchanger for 500 and 520 Series Detectors

- FAA-500-TTL Test Adapter with Magnet for 500 and 520 Series Detectors

1.1 Performance Features

– Fulfills the highest aesthetic demands through the flush-mounting design and the

possibility of color toning

– Smooth, easily-cleaned detector surface

– Quick and easy insertion and exchange of the detector thanks to innovative detector

locking mechanism (click and lock principle)

– Easily-visible two-color LED for display of alarm, trouble and test mode

– Self-monitoring of the sensors: contamination level can be read in test mode

– Active adjustment of the threshold (drift compensation) if the optical sensor becomes

contaminated

– Active adjustment of the threshold (drift compensation) of the chemical sensor

– Increased detection and false alarm immunity thanks to evaluation of the time behavior of

fire and disturbance variables

– Activation of a remote indicator is possible (not for relay bases)

– Easily accessible connection terminals

– Service accessories for simple and comfortable detector test and exchange

– When using the FAA‑500‑TTL test adapter, an integrated reed switch automatically

switches the detector into the test mode (display via detector LED, flashes green once

per second).

– Can be connected to the LSN fire panels FPA‑1200, FPA‑5000 (both with CZM module or

4CON module on LSN loop), UEZ2000 LSN, UGM2020 and to other fire panels or their

receiver modules with identical connection conditions.

– EN54‑7 certified.

1.2 System Description

All detectors in the 500 Series are equipped with two optical sensors and a pollution sensor.

The FCP‑OC500 Multisensor Detector contains a gas sensor as an additional detection

channel.

All sensor signals are analyzed continually by the internal signal evaluation processor and are

linked with each other by specially developed algorithms.

By linking the optical sensors and the gas sensor, the OC detector can also be used in places

where the work carried out gives rise to small amounts of smoke, steam or dust. The alarm

will only be triggered automatically if the signal combination corresponds with the detector’s

programmed characteristic diagram. Consequently, an extremely high tolerance to unwanted

alarms is achieved.

Conventional Automatic Detectors Product Description | en 7

Bosch Sicherheitssysteme GmbH Operation Guide 2019.11 | 5.0 | F.01U.003.962

1.3 Configuration of the Detector

1 1

Figure1.3: Detector front panel with sensors

2 3

Figure1.4: Side view of detector cover

Position Description Position Description

1 Optical sensor 5 Two-color LED:

red = alarm

green = test mode/trouble

2 Receiver (photo diodes) 6 Pollution sensor

3 Transmitter (LEDs) 7 Measuring area

4 CO sensor (only OC-variants)

1.4 Functional Description of the Sensor Technology

Optical sensor (smoke sensor)

The optical sensor (refer to Configuration of the Detector (1)) operates according to the

scattered light principle.

The LEDs (refer to Configuration of the Detector (3)) transmit light at a defined angle into the

measuring area (refer to Configuration of the Detector (7)). In case of fire, the light is

scattered by the smoke particles and strikes the photo diodes (refer to Configuration of the

Detector (2)), which transform the quantity of light into a proportional electrical signal.

The effects of daylight and commercial lighting sources are filtered out with an optical daylight

filter and by the use of electronic filtering and phase-locked rectification (ambient light

stability: dazzling test EN54‑7).

The various light-emitting and photo diodes of the detector are individually activated.

Consequently, signal combinations are produced that are independent of each other and

ideally suitable for the detection of smoke, which makes it possible to differentiate between

smoke and interference agents (insects, objects). In addition, the time characteristics and the

correlation of the optical sensor signals for the fire or interference detection are evaluated.

Moreover, plausibility checking of the various signals makes it possible to detect errors in the

evaluation electronics and the LEDs.

8en | Product Description Conventional Automatic Detectors

2019.11 | 5.0 | F.01U.003.962 Operation Guide Bosch Sicherheitssysteme GmbH

Chemical sensor (CO gas sensor)

The gas sensor (refer to Configuration of the Detector (4), only FCP‑OC500(-P)) detects

mainly the carbon monoxide (CO) that is produced by a fire, but it also detects hydrogen (H)

and nitrogen monoxide (NO).

The basic measuring principle is CO oxidation on an electrode and the measurable current

that arises from this. The sensor signal value is proportional to the concentration of gas.

The gas sensor supplies additional information in order to reliably suppress the disturbance

variables.

Pollution sensor

The contamination level of the detector surface is measured and evaluated continuously by the

pollution sensor (refer to Configuration of the Detector (6)).

1.5 LED Operation

The two-color LED of the detector indicates the operation and alarm statuses.

During the whole life cycle, the sensors are self-monitored and the sensitivity is self-adjusted

according to the programmed threshold.

In case of an alarm, the LED turns red. The detector is set back to standby if the alarm is reset

via the fire panel and if the cause of the alarm is gone.

LED Operation

Status LED

Standby off

Alarm red

Trouble off

Test mode green, flashes once every second

In test mode, the contamination level can be read via the number of the red LED flashes (refer

to Reading the Contamination Level, page 23).

Conventional Automatic Detectors Planning Notes | en 9

Bosch Sicherheitssysteme GmbH Operation Guide 2019.11 | 5.0 | F.01U.003.962

2 Planning Notes

Notice!

The 500 Series detectors are approved for indoor use only.

– Country-specific standards and guidelines must be observed during the planning phase.

– The FCP‑OC500, like the FCP‑O500, is planned according to the guidelines for optical

detectors (refer also to EN54 and VDS2095).

– A hemispherical space (1) with a radius of 50cm must remain free below the detector

(2).

Care must be taken to ensure that no people, larger animals, plants, opening doors or any

objects intrude into this area and that no parts of the detector surface become covered.

50 cm

Figure2.1: Radius

– The detector may only be installed in a position which is out of arm's reach.

Minimum installation height recommended: 2.70m.

– The 500 Series Detectors may not be installed in rooms with data transmission by means

of high-intensity infra-red light (e.g. in rooms with IR systems for interpreters).

– The detectors must be mounted so that they are not exposed to any direct sunlight.

– A minimum distance of 50cm from lamps must be maintained.

The detectors may not be mounted in a cone of light from lamps.

– Maximum permitted air speed: 20m/s.

10 en | Installation Conventional Automatic Detectors

2019.11 | 5.0 | F.01U.003.962 Operation Guide Bosch Sicherheitssysteme GmbH

3 Installation

Notice!

The 500 Series Detectors may only be installed with an FCA‑500‑EU or FCA‑500‑E‑EU Detector

Base in combination with an FAA‑500‑BB Ceiling Mount Back Box or an FAA‑500‑SB-H Surface

Mount Back Box.

Notice!

By default, the bases are equipped with a spring for mounting the detector in concrete and

wooden ceilings. This spring is identifiable by the blue marking. For mounting a detector in a

false ceiling panel you can use the additional, softer spring in the package (yellow marking).

In this use case, the detector must not be subjected to strong vibrations (> 350 m/s). The

shock resistance according to EN 54-7 is not warranted then.

3.1 Ceiling Mount Back Box

Figure3.1: Ceiling mount back box

The ceiling mount back box (refer to figure) is made of white polypropylene.

It has four cable bushings with tightly-closing rubbers lips of polyflam that are suitable for

cable diameters up to 1.4cm.

When used with a base, approx. 30cm of cable length can be accommodated in the upper

area of the ceiling mount back box.

Notice!

The false ceiling may have a maximum thickness of 32mm.

Above the false ceiling, a free height of at least 11cm is required.

4Bore a circular hole with a diameter of 130mm (tolerance -1mm to +5mm) in the false

ceiling.

Notice!

A hole saw with Ø 133mm can be obtained from:

Wittmann-Komet, Metal Cutting Saws GmbH & Co. KG, Alte Str. 28, D-79576 Weil am Rhein,

Tel.++49‑7621‑9783-0, www.wittmann-komet.de

129 m m

104 m m

Figure3.2: Plan view and side view of the ceiling mount back box FAA‑500‑BB

Andere Handbücher für FCP-O 500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bosch Sicherheitssensor Handbücher

Bosch

Bosch DS820 Sicherheitsleitfaden

Bosch

Bosch Photobeam 5000 Betriebsanleitung

Bosch

Bosch SMT500 Bedienungsanleitung

Bosch

Bosch 440 Series Bedienungsanleitung

Bosch

Bosch ISM-BLD1 Bedienungsanleitung

Bosch

Bosch GMS 120 Bedienungsanleitung

Bosch

Bosch 520 Series Bedienungsanleitung

Bosch

Bosch AVENAR detector4000 Bedienungsanleitung

Bosch

Bosch UniversalDetect Bedienungsanleitung

Bosch

Bosch ISC-PPR1-WA16G Bedienungsanleitung

Bosch

Bosch AVIOTEC IPSTARLIGHT 8000 Technisches Handbuch

Bosch

Bosch ISN-SM-50 Bedienungsanleitung

Bosch

Bosch 200 C Gebrauchs- und Pflegehandbuch

Bosch

Bosch TriTech Bedienungsanleitung

Bosch

Bosch FAA-420-RI-ROW Bedienungsanleitung

Bosch

Bosch D-tect 150 Bedienungsanleitung

Bosch

Bosch ISN-SM-50 Bedienungsanleitung

Bosch

Bosch Smart Home RFPR-ZB-SH-EU Bedienungsanleitung

Bosch

Bosch GMS 120 Professional Bedienungsanleitung

Bosch

Bosch 0603683000 Bedienungsanleitung

Bosch

Bosch UniversalDetect Bedienungsanleitung

Bosch

Bosch TriTech+ Professional ISC-PDL1-WAC30G Bedienungsanleitung

Bosch

Bosch ISC-PDL1-W18H Bedienungsanleitung

Bosch

Bosch Blue Line D1-P Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung

Solinst

Solinst 301 Bedienungsanleitung