Bosch DIVAR DIP-7080-00N Bedienungsanleitung
DIVAR IP 7000 2U
DIP-7080-00N, DIP-7082-8HD
en Installation Manual
Table of contents
1Safety precautions 5
1.1 General safety precautions 5
1.2 Electrical safety precautions 6
1.3 ESD precautions 7
1.4 Operating precautions 7
1.5 Important notices 8
1.6 FCC and ICES compliance 8
2System overview 9
2.1 Chassis features 9
2.2 Chassis components 9
2.2.1 Chassis 10
2.2.2 Backplane 10
2.2.3 Fans 10
2.2.4 Mounting rails 10
2.2.5 Power supply 10
2.2.6 Air shroud 10
2.3 System interface 10
2.3.1 Control panel buttons 11
2.3.2 Control panel LEDs 12
2.3.3 Drive carrier LEDs 12
3Chassis setup and maintenance 14
3.1 Removing the chassis cover 14
3.2 Installing hard drives 15
3.2.1 Removing hard drive trays 15
3.2.2 Installing a hard drive 16
3.3 Installing a fixed hard drive 17
3.4 Replacing or installing a DVD-RW 18
3.5 Replacing the internal transcoder device 18
3.6 Replacing or installing the front port panel 18
3.7 Installing the motherboard 19
3.8 Installing the air shroud 19
3.9 Checking the air flow 20
3.10 Replacing the system fans 20
3.11 Power supply 21
3.11.1 Replacing the power supply 22
3.11.2 Replacing the power distributor 23
4Rack installation 24
4.1 Unpacking the system 24
4.2 Preparing for setup 24
4.2.1 Choosing a setup location 24
4.2.2 Rack precautions 24
4.2.3 General system precautions 25
4.2.4 Rack mounting considerations 25
4.3 Rack mounting instructions 26
4.3.1 Separating the sections of the rack rails 26
4.3.2 Installing the inner rails 27
4.3.3 Installing the outer rails to the rack 27
DIVAR IP 7000 2U Table of Contents | en 3
Bosch Sicherheitssysteme GmbH Installation Manual 2013.09 | V2 | DOC
4.3.4 Installing the chassis into the rack 28
4.3.5 Installing the chassis into a Telco rack 29
4.4 Turning on the system 29
5System setup - first steps 30
5.1 Introduction 30
5.2 Setup instruction 30
5.3 Starting the Appliccation 30
5.4 Using Configuration Wizard 31
5.5 Using Bosch VMS Configuration Client 42
5.6 Using Bosch VMS Operator Client 43
6Recovering the unit 44
6.1 System recovery options 44
6.2 RAID disaster recovery 44
6.2.1 Multiple disks failed – theory 46
6.2.2 Multiple disks failed – practice 50
6.2.3 Foreign configuration disk appears in the Windows GUI after booting 54
6.2.4 MegaCLI Commandline Utility 55
7Additional documentation and client software 60
8Appendices 61
8.1 Motherboard 61
8.1.1 Motherboard layout 61
8.1.2 Motherboard component overview 62
8.1.3 Motherboard features 64
8.1.4 Block diagram 66
8.2 Chipset overview 66
8.3 PC health monitoring 67
8.4 Power configuration settings 67
8.5 Power supply 68
8.6 Super I/O 68
8.7 iSCSI support 68
8.8 Overview of the Nuvoton BMC controller 69
4en | Table of Contents DIVAR IP 7000 2U
2013.09 | V2 | DOC Installation Manual Bosch Sicherheitssysteme GmbH
Safety precautions
Observe the safety precautions in this chapter.
General safety precautions
Follow these rules to ensure general safety:
–Keep the area around the system clean and free of clutter.
– Place the chassis top cover and any system components that have been removed away
from the system or on a table so that they won't accidentally be stepped on.
– While working on the system, do not wear loose clothing such as neckties and
unbuttoned shirt sleeves, which can come into contact with electrical circuits or be
pulled into a cooling fan.
– Remove any jewelry or metal objects from your body, which are excellent metal
conductors that can create short circuits and harm you if they come into contact with
printed circuit boards or areas where power is present.
– After accessing the inside of the system, close the system back up and secure it to the
rack unit after ensuring that all connections have been made.
– The system weighs approximately 57 lbs. (25.9 kg) when fully loaded. When lifting the
system, two people at either end should lift slowly with their feet spread out to distribute
the weight. Always keep your back straight and lift with your legs.
!
Warning!
Interruption of mains supply:
Voltage is applied as soon as the mains plug is inserted into the mains socket.
However, for devices with a mains switch, the device is only ready for operation when the
mains switch (ON/OFF) is in the ON position. When the mains plug is pulled out of the
socket, the supply of power to the device is completely interrupted.
!
Warning!
Removing the housing:
To avoid electric shock, the housing must only be removed by qualified service personnel.
Before removing the housing, the plug must always be removed from the mains socket and
remain disconnected while the housing is removed. Servicing must only be carried out by
qualified service personnel. The user must not carry out any repairs.
!
Warning!
Power cable and AC adapter:
When installing the product, use the provided or designated connection cables, power cables
and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire.
Electrical Appliance and Material Safety Law prohibits the use of UL or CSA-certified cables
(that have UL/CSA shown on the code) for any other electrical devices.
1
1.1
DIVAR IP 7000 2U Safety precautions | en 5
Bosch Sicherheitssysteme GmbH Installation Manual 2013.09 | V2 | DOC
!
Warning!
Lithium battery:
Batteries that have been inserted wrongly can cause an explosion. Always replace empty
batteries with batteries of the same type or a similar type recommended by the manufacturer.
Handle used batteries carefully. Do not damage the battery in any way. A damaged battery
may release hazardous materials into the environment.
Dispose of empty batteries according to the manufacturer's instructions.
!
Warning!
Handling of lead solder materials used in this product may expose you to lead, a chemical
known to the State of California to cause birth defects and other reproductive harm.
Notice!
Electrostatically sensitive device:
To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried
out correctly.
When handling electrostatically sensitive printed circuits, grounded anti-static wrist bands
must be worn and the ESD safety precautions observed.
Notice!
Installation should only be carried out by qualified customer service personnel in accordance
with the applicable electrical regulations.
Disposal
Your Bosch product has been developed and manufactured using high-
quality materials and components that can be reused.
This symbol means that electronic and electrical devices that have reached
the end of their working life must be disposed of separately from
household waste.
In the EU, separate collecting systems are already in place for used
electrical and electronic products. Please dispose of these devices at your
local communal waste collection point or at a recycling center.
Electrical safety precautions
Basic electrical safety precautions should be followed to protect you from harm and the
system from damage:
– Be aware of the locations of the power on/off switch on the chassis as well as the room's
emergency power-off switch, disconnection switch or electrical outlet. If an electrical
accident occurs, you can then quickly remove power from the system.
– Do not work alone when working with high voltage components.
– Power should always be disconnected from the system when removing or installing main
system components, such as the motherboard or memory modules. When disconnecting
power, you should first turn off the system and then unplug the power cords from all the
power supply modules in the system.
– When working around exposed electrical circuits, another person who is familiar with the
power-off controls should be nearby to switch off the power if necessary.
1.2
6en | Safety precautions DIVAR IP 7000 2U
2013.09 | V2 | DOC Installation Manual Bosch Sicherheitssysteme GmbH
– Use only one hand when working with powered-on electrical equipment. This is to avoid
making a complete circuit, which will cause electrical shock. Use extreme caution when
using metal tools, which can easily damage any electrical components or circuit boards
they come into contact with.
–The power supply power cords must include a grounding plug and must be plugged into
grounded electrical outlets. The unit has more than one power supply cord. Disconnect
both power supply cords before servicing to avoid electrical shock.
– Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Temperature
Coefficient) fuses on the mainboard must be replaced by trained service technicians only.
The new fuse must be the same or equivalent as the one replaced. Contact technical
support for details and support.
!
Caution!
Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside
down, which will reverse its polarities. This battery must be replaced only with the same or
an equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries
according to the manufacturer's instructions.
!
Caution!
DVD-ROM Laser: This system comes without a DVD-ROM drive but if added: To prevent direct
exposure to the laser beam and hazardous radiation exposure, do not open the enclosure or
use the unit in any unconventional way.
ESD precautions
Electrostatic Discharge (ESD) is generated by two objects with different electrical charges
coming into contact with each other. An electrical discharge is created to neutralize this
difference, which can damage electronic components and printed circuit boards. The
following measures are generally sufficient to neutralize this difference before contact is made
to protect your equipment from ESD:
– Do not use mats designed to decrease electrostatic discharge as protection from
electrical shock. Instead, use rubber mats that have been specifically designed as
electrical insulators.
– Use a grounded wrist strap designed to prevent static discharge.
– Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready
for use.
– Touch a grounded metal object before removing the board from the antistatic bag.
– Do not let components or printed circuit boards come into contact with your clothing,
which may retain a charge even if you are wearing a wrist strap.
– Handle a board by its edges only. Do not touch its components, peripheral chips, memory
modules or contacts.
– When handling chips or modules, avoid touching their pins.
– Put the mainboard and peripherals back into their antistatic bags when not in use.
– For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and the
mainboard.
Operating precautions
The chassis cover must be in place when the system is operating to assure proper cooling. Out
of warranty damage to the system can occur if this practice is not strictly followed.
1.3
1.4
DIVAR IP 7000 2U Safety precautions | en 7
Bosch Sicherheitssysteme GmbH Installation Manual 2013.09 | V2 | DOC
Note:
Please handle used batteries carefully. Do not damage the battery in any way. A damaged
battery may release hazardous materials into the environment. Do not discard a used battery
in the garbage or a public landfill. Please comply with the regulations set up by your local
hazardous waste management agency to dispose of your used battery properly.
Important notices
Accessories - Do not place this unit on an unstable stand, tripod, bracket,
or mount. The unit may fall, causing serious injury and/or serious damage to
the unit. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer. When a cart is used, use caution and care when moving
the cart/apparatus combination to avoid injury from tip-over. Quick stops,
excessive force, or uneven surfaces may cause the cart/unit combination to
overturn. Mount the unit per the manufacturer's instructions.
FCC and ICES compliance
(only for U.S.A. and Canada)
This equipment has been tested and found to comply with the limits for a Class A digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the manufacturer’s instruction manual, may cause
harmful interference with radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case you will be required to correct the
interference at your own expense.
1.5
1.6
8en | Safety precautions DIVAR IP 7000 2U
2013.09 | V2 | DOC Installation Manual Bosch Sicherheitssysteme GmbH
System overview
DIVAR IP 7000 is an affordable, simple and reliable all-in-one recording, viewing and
management solution for network surveillance systems of up to 64 channels (with 32 channels
pre-licensed). Running the full Bosch VMS (Video Management System) solution and powered
by Bosch VRM (Video Recording Manager) software, the DIVAR IP 7000 is an intelligent IP
storage device that eliminates the need for separate NVR (Network Video Recorder) server and
storage hardware.
The 2U rack mount unit combines advanced management and state-of-the-art recording
management into a single cost-effective, plug and play IP recording appliance for IT-minded
customers which are seeking for a state-of-the-art “second generation” NVR recording
solution.
DIVAR IP 7000 features:
– Instant real time access to video
View high quality HD video despite low or limited bandwidth connections. Dynamic
Transcoding technology ensures that you can view your video immediately — anytime,
anywhere.
– Easy installation
DIVAR IP 7000 2U features wizard based set-up and centralized configuration to reduce
installation times. All components are pre-installed and pre-configured. Simply connect to
the network and turn on the unit — DIVAR IP 7000 2U starts recording straight out of the
box.
– Access to Bosch VMS
After starting the system, immediate access to the Bosch VMS management application is
offered by a customized user interface. The ability to use one central user interface for
configuration and operation management reduces installation and training requirements,
and helps to keep ongoing system management costs low.
Chassis features
The chassis includes the following features:
–CPU (Intel QuadCore)
– Internal SSD (80 GB) for operating system and application operations
– 8 slots for U320 SCSI or SAS/SATA drives. These drives are hot swappable. Once setup
correctly, these drives can be removed without powering down the server. In addition,
these drives support SAF-TE (SCSI) and SES2 (SAS/SATA)
– Seven low-profile I/O expansion slots.
– Graphic card AMD V3900 (1x DVI, 1x Display Port output)
– Sound card
– One slim DVD-RW drive and one slim Floppy Drive. These drives allow you to quickly
install or save data.
– One internal USB Transcoder device
Other onboard features are included to promote system health. These include various
cooling fans, a convenient power switch, reset button, and LED indicators.
Chassis components
This chapter describes the most common components included with your chassis. For more
information, see the installation instructions detailed later in this manual.
2
2.1
2.2
DIVAR IP 7000 2U System overview | en 9
Bosch Sicherheitssysteme GmbH Installation Manual 2013.09 | V2 | DOC
Chassis
The chassis includes 8 hard drive bays and supports a 2U backplane, 3 fans and two power
supplies.
Backplane
Each chassis comes with a 2U backplane. The backplane accepts SAS/SATA hard drives.
!
Warning!
Use caution when servicing and working around the backplane. Hazardous voltage or energy
is present on the backplane when the system is operating. Do not touch the backplane with
any metal objects and make sure no ribbon cables touch the backplane.
Fans
The chassis supports 3 system fans that are powered from the motherboard. These fans are
2U high and are powered by 3-pin connectors.
Mounting rails
The unit can be placed in a rack for secure storage and use. To setup your rack, follow the
step-by-step instructions included in this manual.
Power supply
Each chassis model includes 2 high-efficiency power supplies (redundant). In the unlikely
event your power supply fails, replacement is simple and can be accomplished without tools.
Air shroud
Air shrouds are shields, usually plastic, which conduct the airflow directly to where it is
needed. Always use the air shroud included with your chassis.
System interface
There are several LEDs on the front and rear of the chassis. The LEDs show the over-all status
of the system and the activity and health of specific components.
2.2.1
2.2.2
2.2.3
2.2.4
2.2.5
2.2.6
2.3
10 en | System overview DIVAR IP 7000 2U
2013.09 | V2 | DOC Installation Manual Bosch Sicherheitssysteme GmbH
Andere Handbücher für DIVAR DIP-7080-00N
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Bosch Sicherheitssystem Handbücher
Bosch
Bosch DIP-3042-2HD Bedienungsanleitung
Bosch
Bosch FMC-210-DM-G-R Bedienungsanleitung
Bosch
Bosch Plena BGM Source Bedienungsanleitung
Bosch
Bosch AP1-T Bedienungsanleitung
Bosch
Bosch LTC 8900 Series Bedienungsanleitung
Bosch
Bosch MBV-BPRO-45 Merkblatt
Bosch
Bosch B Series Bedienungsanleitung
Bosch
Bosch DIVAR IP all-in-one 7000 3U Bedienungsanleitung
Bosch
Bosch DS484Q Bedienungsanleitung
Bosch
Bosch PRAESENSA Bedienungsanleitung
Bosch
Bosch FK 100 LSN Bedienungsanleitung
Bosch
Bosch SOLUTION ULTIMA Bedienungsanleitung
Bosch
Bosch GVS1000 Bedienungsanleitung
Bosch
Bosch Plena Power Amplifier Leitfaden
Bosch
Bosch Plena PLE-1CS Referenzhandbuch
Bosch
Bosch CP700B Anleitung zur Verwendung
Bosch
Bosch Carephone 61 Bedienungsanleitung
Bosch
Bosch ICP-AMAX4-P2-EN Bedienungsanleitung
Bosch
Bosch LTC 9441 Series Bedienungsanleitung
Bosch
Bosch AMAX 2100 Gebrauchsanweisung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung