Bosch D340 Bedienungsanleitung

Installation Guide

Duct Smoke Detector

Housing

D340

D340 |Installation Guide | 1.0 Overview

2 Bosch Security Systems, Inc. | 7/09 | F01U071685-06

Trademarks

The National Fire Alarm Code®is a registered

trademark of the National Fire Protection Association.

Life Safety Code®is a registered trademark of the

National Fire Protection Association.

1.0 Overview

The D340 Air Duct Smoke Detector Housing is

designed to mount to the ducts of heating, ventilation,

and air-conditioning (HVAC) systems to monitor the

presence of smoke in the conditioned air.

Use the D340 with the D285DH Photoelectric Smoke

Detector (provided separately). The detector is

combined with an efficient housing design to sample

the air passing through a duct and detect potentially

hazardous conditions. When it detects smoke, the

detector sends an alarm signal to the control panel.

The control panel initiates the necessary action to shut

off fans and blowers or to switch to other air handling

systems.

The D340 operates on a two-wire loop, and requires a

smoke detector head.

Test the system by placing an external magnet on the

housing or switching the keyswitch from a Remote

Test station. Reset control requires a 24 V supply from

the control panel or an external power supply.

You can reset the detector by shutting down zone

power. If your system has a D344-RT Remote Test Kit,

you can reset the system using the keyswitch.

Install the D340 according to:

•NFPA 90A: Standard for the Installation of Air

Conditioning and Ventilating Systems

•NFPA 72: National Fire Alarm Code®

•NFPA 101: Life Safety Code®

•IBC: International Building Code

•IFC: International Fire Code

•Any applicable local and state codes

•Local authority having jurisdiction (AHJ)

2.0 D340 Options

Table 1: D340 Options

Options Description

D285DH Photoelectric smoke detector head

D344-1.5 1.5 ft (0.5 m) sample tube

D344-3 3 ft (1 m) sample tube

D344-5 5 ft (1.5 m) sample tube

D344-RT Remote Test Kit (D307)

D344-RL Remote LED Indicator Kit (D306)

D344-TF Tube filters for sample and exhaust tubes

(20 per package)

SMK-TM Test magnet

DRA-5 Remote alarm indicator

D275 End-of-line (EOL) module

3.0 Assembly

The D340 includes:

•One housing, power card, and cover assembly

•Two #10-24 x 1 in. machine screws for mounting

•Two #10-24 jack nuts

•One exhaust tube

•Two tube clamps with four screws

•Two foam gaskets

•Two air filters

•One drilling template

•One cover gasket

The D340P also includes a smoke detector head and

1.5 ft (0.5 m) tube.

D340 |Installation Guide | 4.0 Sample Tubes

Bosch Security Systems, Inc. | 7/09 | F01U071685-06 3

4.0 Sample Tubes

The sample tubes must extend across the width of the

duct. The three sizes of sample tubes are:

•D344-1.5 (1.5 ft [0.46 m])

•D344-3 (3 ft [0.91 m])

•D344-5 (5 ft [1.52 m])

Sample tubes include an end plug that must be

installed in the narrow end of the tube (Figure 1).

Figure 1: D344-1.5 Sample Tube

1 - Set screw 2 - End plug

You can combine or cut sample tubes to make

different lengths. A sample tube can be a maximum

length of

10 ft (3 m) or a minimum length of 1 ft (0.3 m). For

example, you can join a 3 ft (1 m) and a 5 ft (1.5 m) to

make an 8 ft (2.4 m) sample tube.

To combine sample tubes:

1. Remove the roll pin and set screw from one of the

sample tubes.

2. Remove the end plug from the other sample tube.

3. Push the flared end over the sample tube you want

to lengthen.

4. Align the holes, insert the set screw, and reinstall

the end plug. For example, if you want a 7 ft (2 m)

sample tube, combine a 3 ft (1 m) sample tube and

a 5 ft (1.5 m) sample tube. Then cut 1 ft (0.3 m)

from the narrow end to get the necessary length.

Sample tubes must have at least 12

sample holes within the duct. Do not cut

sample

tube to less than 12 sample holes.

Sample tubes over 3 ft (1 m) must be supported at

the end opposite the duct detector. The support

hole should be 1 in. to 2 in. (2.5 cm to 5 cm) below

the entry hole to allow for possible moisture

drainage (Figure 2).

Figure 2: Support Hole Position

1 - 1 in. to 2 in. (2.5 cm to 5 cm)

5. Seal the gap between duct and sample tube. You

can remove up to 6 in. (15 cm) from the D344-1.5

for 1 ft (0.3 m) duct installations.

When using the D344-1.5 in installations where the

duct width is between 12 in. (31 cm) and 18 in.

(46 cm), cover some of the sample holes. The

D344-1.5 has 19 sample holes, but only 12 are

required for normal installations. Depending on

the length, you might have to cover some of the

holes with duct tape. Use even spacing when

covering the sample holes to allow an even sample

across the width of the duct. Refer to Figure 3.

Figure 3: D344-1.5 Sample Tube

1 - Place tape over these sample holes

D340 |Installation Guide | 5.0 Mounting

4 Bosch Security Systems, Inc. | 7/09 | F01U071685-06

5.0 Mounting

5.1 Preparing the Duct

You must verify the duct air flow and velocity. The

D340 is designed for use in air handling systems with

air velocities between 300 ft/min and 4000 ft/min

(1.5 m/sec to 20.3 m/sec). Check the HVAC

engineering specifications to ensure the air velocity in

the duct falls within these parameters. If necessary, use

a velocity meter to check the air velocity in the duct.

5.1 Determining the Mounting Location

To obtain a representative air sample, avoid

stratification and dead air space. These conditions can

be caused by return duct openings, sharp turns,

connections, or long, uninterrupted runs. For this

reason, place the D340 in the range of six to ten times

the width of the duct from any uninterrupted run.

Refer to Figure 4 and Figure 5.

Figure 4: Typical D340 Placement – Example A

1 - Bend or other obstruction

2 - Six to ten times the width of the duct

3 - Width of duct

Figure 5: Typical D340 Placement – Example B

1 - Return air inlet

2 - Six to ten times the width of the duct

3 - Width of duct

5.2 Positioning the D340

The D340 can be mounted in any direction of 90°

increments without regard to the air flow direction

(Figure 6).

Figure 6: D340 Positions

2 2

1 1

1 - Air flow

2 - Correct mounting position

3 - Incorrect mounting position

D340 |Installation Guide | 5.0 Mounting

Bosch Security Systems, Inc. | 7/09 | F01U071685-06 5

1. Locate the D340 mounting template (Figure 7) and

remove it from its backing.

Figure 7: D340 Mounting Template

5DUCT SMOKE DETECTOR

MOUNTING TEMPLATE

REMOVEABLE AFTER DRILLING

1 - 16 in. (41 cm)

2 - 6.5 in. (16.5 cm)

3 - Two 1-3/4-in. (45-mm) diameter holes for the

sample tubes

4 - Two 3/8-in. (9.5-mm) diameter holes for

mounting to the duct

5 - 1.5 in. (38.1 mm)

6 - 8.0 in. (20.5 cm)

2. Place the template over the desired location on the

duct (Figure 8).

Figure 8: D340 Template Placement

(2) 1-3/4 in. (44.5 mm) DIA. HOLES FOR SAMPLING TUBES

(2) 3/8 in. (9.5 mm) DIA. HOLES FOR DUCT MOUNTING

16.070 in. (40.8 cm)

6.480 in. (16.5 cm) DUCT SMOKE DETECTOR

MOUNTINGTEMPLATE

REMOVEABL EA FTER DRILL ING

3. Drill out the required holes and remove any

remaining debris.

4. Remove the template.

5. Place a #10-24 jack nut (Figure 9) in each of the

3/8 in. (9.5 mm) holes.

Figure 9: Jack Nuts

6. Insert the #10-24 x 1 in. machine screws into the

jack nuts and firmly tighten.

This attaches the jack nuts to the duct. You might

have to hold the jack nuts with a installer wrench

or a pair of pliers while tightening the screws to

stop the jack nut from spinning in the hole.

Remove the screws for later use.

7. Place the two foam gaskets over the sample and

exhaust ports on the back of the D340 (Figure 10).

Figure 10: Gasket Placement

1 - Foam gasket (2)

8. Mount the D340 to the jack nuts using the

supplied

10-24 x 1-in. machine screws (Figure 11).

Remember that overtightening the screws can

cause excessive bowing of duct.

Figure 11: Mounting the D340 to the Jack Nuts

1 - Two 10-24 x 1-in. machine screws

9. Locate the wiring knockout holes (Figure 12).

D340 |Installation Guide | 5.0 Mounting

6 Bosch Security Systems, Inc. | 7/09 | F01U071685-06

Figure 12: Wiring Knockout Locations

1 - Wiring Knockouts (5) 2 - Earth ground screw

D340 |Installation Guide | 5.0 Mounting

Bosch Security Systems, Inc. | 7/09 | F01U071685-06 7

10. Locate the sample and exhaust tubes (Figure 13).

Ensure the sample tube has a plug installed at the

narrow end of the assembly.

Figure 13: Exhaust and Sample Tubes

1 - Exhaust tube

2 - Leave end open

3 - Sample tube

4 - Insert plug

11. Note the direction of the airflow in the duct. The

sampling holes in the sample tube must face into

the air flow (Figure 14). The exhaust tube must be

downwind from the sample tube (Figure 15).

Figure 14: Duct Air Flow

1 - Air flow 2 - Sample holes

Figure 15: Exhaust Tube Position

1 - Air flow

2 - Sample tube

3 - Exhaust tube down stream from sample tube

12. Insert the sample and exhaust tubes into the D340,

ensuring the sample tube holes face into the air

flow. Ensure the tube alignment point set into the

D340.

13. Secure the tubes in place using the tube clamps

provided (Figure 16).

Figure 16: Sample and Exhaust Tubes in D340

1 - Exhaust tube

2 - Sample tube

3 - D340

4 - Tube clamps (2)

14. Place the tube filters over the open ends of the

sample and exhaust tubes (Figure 17).

Figure 17: Tube Filters

1 - Exhaust tube

2 - Sample tube

3 - D340

4 - Tube filters (2)

NFPA-72 requires a semi-annual visual

inspection of detector housings. Clean or

replace the tube filters at this time. If

replacement filters are needed, order the

D344-TF.

D340 |Installation Guide | 6.0 Selecting the Jumper

8 Bosch Security Systems, Inc. | 7/09 | F01U071685-06

6.0 Selecting the Jumper

6.1 Location

Figure 18 shows the locations of the tamper and reset

jumpers on the power card.

Figure 18: Jumper Locations

Tamper

Disable Reset

Disable

14 13 12 11 10 9

BBR

LRE

KND

1 - D340 Power card

2 - Tamper jumper

3 - Reset jumper

The Tamper Jumper (Figure 19) enables or disables the

housing cover Tamper Switch. When this jumper is

enabled, a trouble is indicated if the cover is removed.

Figure 19: Tamper Jumper

1 - Disabled 2 - Enabled

The Reset Jumper (Figure 20) enables or disables the

Remote Reset (keyswitch). The Power Off Reset from

the control panel zone functions normally regardless of

the jumper setting.

Figure 20: Reset Jumper w/Remote Display

Units

1 - Disabled 2 - Enabled

Disable the Reset jumper whenever you are

not using the D344-RT (D307).

7.0 Wiring

7.1 Terminals

Figure 21: Terminal Wiring

14 13 12 11 910

(+) (-) OUT IN

3 4

1 - Optional external power (24 VAC/VDC)

2 - Remote LED

3 - Loop (+)

4 - Loop (-)

7.2 Primary Power

The D340 is designed for a two-wire loop power

ranging from 8.5 VDC to 32 VDC. For Remote Test

or Remote LED, you must use an external 24

VDC/VAC that can supply a minimum of 170 mA.

D340 |Installation Guide | 7.0 Wiring

Bosch Security Systems, Inc. | 7/09 | F01U071685-06 9

7.3 D340 Two-Wire D344-RT (D307)

NFPA-72 requires that where in-duct

smoke detector housings are installed in

concealed locations more than 10 ft (3 m)

above the finished floor or in arrangements

where the detector’s alarm indicator is not

visible to responding personnel, the

detectors have remote alarm indicators.

Do not exceed 500 ft (152 m) between the

D344-RT (D307) Remote Test/Indicator

Plate and the D340. Use 18 AWG (1.2

mm) or larger wire.

Figure 22: D340 Two-wire to the D344-RT (D307)

Wiring

14 13 12 11 10 9

1 - Voltage in (+)

2 - Voltage out (-)

3 - Yellow LED

4 - Voltage monitor

5 - Ground (-)

6 - Remote test

7 - Green LED

8 - Red LED

9 - D340

10 - D307

7.4 D344-RL Remote Indicator Plate

Do not exceed a distance of 500 ft (150 m)

between the D344-RL (D306) Remote

Indicator Plate and the D340. Use 18

AWG (1.2 mm) or larger wire.

Figure 23: D344-RL (D306) Wiring

1 - D340 Power card

2 - D306 Remote indicator plate

3 - Yellow wire

4 - Violet wire

5 - Black wire

Ground (-)

7 - Green wire

8 - Red wire

7.5 DRA-5 Remote Alarm LED

Do not exceed a distance of 500 ft (150 m)

between the DRA-5 Remote Alarm

Indicator and the D340. Use 18 AWG (1.2

mm) or larger wire.

D340 |Installation Guide | 7.0 Wiring

10 Bosch Security Systems, Inc. | 7/09 | F01U071685-06

Figure 24: DRA-5 Wiring

ALARM

14 13 12 11 10 9

14 13

(+) (-)

12 11 9

OUT IN

1 3

1 - Optional external

power (24 VAC/VDC)

2 - Remote LED

3 - Loop (+)

4 - Loop (-)

5 - DRA-5

6 - White wire

7 - Red wire

Andere Handbücher für D340

Inhaltsverzeichnis

Andere Bosch Rauchmelder Handbücher

Bosch

Bosch FAD-325-V2F Bedienungsanleitung

Bosch

Bosch F220 Bedienungsanleitung

Bosch

Bosch ISW-EN1242 Bedienungsanleitung

Bosch

Bosch twinguard Bedienungsanleitung

Bosch

Bosch Titanus Pro?Sens TP-1 A Bedienungsanleitung

Bosch

Bosch FAS-420-TM Bedienungsanleitung

Bosch

Bosch FAP-520 Bedienungsanleitung

Bosch

Bosch D296 Series Benutzerhandbuch

Bosch

Bosch D296 Series Bedienungsanleitung

Bosch

Bosch AVENAR 4000 FAP-425-O Bedienungsanleitung

Bosch

Bosch Fireray3000 Bedienungsanleitung

Bosch

Bosch FAS-420-TM Bedienungsanleitung

Bosch

Bosch FRP-OW3000 Bedienungsanleitung

Bosch

Bosch FAS-420-TM Bedienungsanleitung

Bosch

Bosch FCS-320-TP Series Bedienungsanleitung

Bosch

Bosch RFSM-A Bedienungsanleitung

Bosch

Bosch FAD-425-O-R Bedienungsanleitung

Bosch

Bosch FERION 1000 O Bedienungsanleitung

Bosch

Bosch FAD?420?HS?EN Bedienungsanleitung

Bosch

Bosch D296 Series Benutzerhandbuch

Bosch

Bosch FERION 5000 OW Bedienungsanleitung

Bosch

Bosch DRA 12/24 Bedienungsanleitung

Bosch

Bosch FCS-320-TP2 Installationshandbuch

Bosch

Bosch FAP-OT 420 KKW Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

BRK electronic

BRK electronic First Alert P1010 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Safetec

Safetec SDS-2/6 Betriebsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung