Bosch BAT 135 Bedienungsanleitung

BAT 135 Battery Tester Operating Instructions

en |2|Operating Instructions | BAT 135 Battery Tester

BAT 135 | REV. A | JANUARY 2018

Contents

1 Introduction 3

2 Safety Warnings and Instructions 3

3 Paper Loading 3

4 Test Preparation 4

5 Battery Testing 4

6 Start/Stop Test 5

7 System Test 6

8 Glossary 7

9 Warranty Terms and Conditions 8

Appendix A - System Analyzer Screens 9

Appendix B - Surface Charge Notice 10

Appendix C - Decoding Test Codes 12

BAT 135 | REV. A | JANUARY 2018

Operating Instructions | BAT 135 Battery Tester | 3|en

1 Introduction

The BAT 135 Battery Tester is used to test 6 and 12 volt batteries, and to test 12 and 24 volt charging systems. The

suggested operation range is from 0 degrees Centigrade (32 degrees Fahrenheit) to 50 degrees Centigrade (122

degrees Fahrenheit) in ambient temperature.

2 Safety Warnings and Instructions

WARNING

This product can expose you to chemicals including arsenic, which is known to the State of California to

cause cancer. For more information, go to www.P65Warnings.ca.gov.

CAUTION

Do not expose the tester to rain or snow.

} Working in the vicinity of a lead acid battery is dangerous. Batteries generate explosive gases during normal

operation. For this reason it is of utmost importance, if you have any doubt, that you read these instructions very

carefully each time you use your tester.

} To reduce risk of battery explosion, follow these instructions, those published by the battery manufacturer, and

the manufacturer of any equipment you intend to use in the vicinity of the battery. Observe cautionary markings

on these items.

} Another person should be within range of your voice or close enough to come to your aid when you work near a

lead acid battery.

} Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.

} Wear safety glasses and protective clothing.

} If battery acid contacts your skin or clothing, wash immediately with soap and water. If acid enters your eye,

immediately flood the eye with running cold water for at least ten minutes and seek immediate medical attention.

} NEVER smoke or allow a spark or flame in vicinity of the battery or engine.

} Be extra cautious to reduce the risk of dropping a metal tool onto the battery. It could spark or short-circuit the

battery or other electrical parts and could cause an explosion.

} Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead acid

battery. These items can produce a short-circuit current high enough to weld a ring or like to metal causing a

severe burns.

3 Paper Loading/Replacement

Do the following to load paper:

1. Open the clear cover.

2. Insert a new/replacement paper roll (PN 1699200246) into the paper feeder for auto running the paper into the

printer.

3. Pull the paper slowly and straight from the paper roll in the chamber.

Note: The battery clamp replacement part number is 1699200245.

en |4|Operating Instructions | BAT 135 Battery Tester

BAT 135 | REV. A | JANUARY 2018

4 Test Preparation

1. Ensure that the area around the battery is well ventilated while the battery is being tested.

2. Clean battery terminals. Be careful to keep corrosion from coming in contact with your eyes.

3. Inspect the battery for cracked or broken case or cover. If the battery is damaged, do not use the tester.

4. If the battery is not sealed maintenance free, add distilled water in each cell until the battery acid reaches the

level specified by the manufacturer. This helps purge excessive gas from cells. Do not overfill.

5. If necessary to remove battery from vehicle to test, always remove the ground terminal from the battery first.

Make sure all accessories in the vehicle are off to prevent arcing.

5 Battery Testing

CAUTION

Before you test a battery in a vehicle, turn off the ignition and all accessories and loads. Close all

vehicle doors and the trunk lid.

Note: Each time you connect the tester to a battery, the tester will run a quick cable verification to ensure a

proper connection through the output cables to sensors in the clamp jaws. If the connection checks out OK, the

display will momentarily flash and proceed to the Home Screen. In operation the tester will only show three

results: CHECK CLAMPS / VOLTAGE HIGH / VOLTAGE LOW.

1. Make sure you have put 6 pcs 1.5V batteries into the battery chamber. Oxyride batteries are not recommended

because of the initial 1.7 Volt output. If the 1.5V battery runs out of power, the screen will display “POWER

LOW.” Replace those 6 pcs 1.5V batteries before starting the test.

Note: Nothing will be seen on the display until the tester is connected to a vehicle battery.

2. Make sure the battery terminals are clean. Wire brush them if necessary. Clamp the black load lead to the

vehicle negative battery terminal. Clamp the red load lead to the vehicle positive battery terminal. Clamp on the

lead part of the terminal only, as clamping on the iron part of the terminal will lead to inaccurate test results.

3. View the

System Analyzer Screens

diagram (

Appendix A

) for selection options.

4. Press to select Battery Test, then press ENTER.

5. Press to select one of the following battery types:

}FLOODED

}AGM FLAT

}AGM SPIRAL

}VRLA/GEL

Press ENTER to confirm choice.

6. Press to select one of the following battery ratings.

}CCA/SAE

}EN

}JIS

}DIN

}IEC

}CA/MCA

Press ENTER to confirm choice.

7. Press to select the battery capacity of SAE from one of the following:

}CCA/SAE: 40~2000

}EN: 40~1885

}DIN: 25~1120

}IEC: 30~1320

}JIS: By battery type number

}CA/MCA: 50~2400

Press ENTER to begin the test.

Example

BAT 135 | REV. A | JANUARY 2018

Operating Instructions | BAT 135 Battery Tester | 5|en

8. Press to confirm the temperature.

Press ENTER to begin the test.

Note: Before the test is started, you can always return to the previous page by pressing and holding ENTER for

two seconds.

Important: If prompted by the tester to remove a surface charge, refer to

Appendix B, Surface Charge Notice

6 Start/Stop Test

1. Press to select Start/Stop Test, then press ENTER.

2. Press to select one of the following the battery types:

}EFB

}AGM FLAT

Press ENTER to confirm choice.

3. Press to select one of the following battery ratings:

}CCA/SAE

}EN

}JIS

}DIN

}IEC

}CA/MCA

Press ENTER to confirm choice.

4. Press to input one of the following battery capacities of SAE:

}CCA/SAE: 40~2000

}EN: 40~1885

}DIN: 25~1120

}IEC: 30~1320

}JIS: By battery type number

}CA/MCA: 50~2400

Press ENTER to begin test.

5. Press to confirm temperature.

Press ENTER to begin test.

Note: Before the test is started, you can always return to the previous page by pressing and holding ENTER for

two seconds.

Important: If prompted by the tester to remove a surface charge, refer to

Appendix B, Surface Charge Notice

Example

en |6|Operating Instructions | BAT 135 Battery Tester

BAT 135 | REV. A | JANUARY 2018

7 System Test

1. Press ENTER to view the System Test screen.

2. Turn off all vehicle accessory loads such as light, air conditioning, radio, etc. before starting the engine.

3. When the engine is started, one of three results will be displayed, along with the reading taken:

}Cranking Volts Pass

The system is showing normal draw. Press ENTER to start the charging system test.

}Cranking Volts Fail

The cranking voltage is below normal limits. Troubleshoot the starter with the manufacturer’s recommended

procedure.

}Cranking Volts Not Detected

The cranking voltage is not detected.

4. If the cranking voltage is normal, press ENTER to begin the charging system test.

5. Press ENTER. The following screen appears.

6. Press ENTER. One of the following two results for the Charging Volts Test at Idle will be displayed.

}PASS

}FAIL

7. Monitoring the charging system at idle, press ENTER for the charging system with accessory loads. Turn on the

blower to High (heat), High Beam headlights, and Rear Defogger. Do not use cyclical loads such as air

conditioning or windshield wipers.

8. When testing older model diesel engines, run up the engine to 2500 rpm for 15 seconds. You will view the

following screen:

Example

BAT 135 | REV. A | JANUARY 2018

Operating Instructions | BAT 135 Battery Tester | 7|en

9. Press ENTER to determine the amount of ripple from the charging system to the battery. One of two testing

results will be displayed, along with the reading taken.

}Ripple Detected

Diodes function well in the alternator / stator.

}No Ripple Detected

One or more diodes in the alternator are not functioning or there is stator damage. Ensure that the alternator

mounting is sturdy and that the belts are in good shape and functioning properly. If the mounting and belts

are good, replace the alternator.

10. Press ENTER to continue testing the charging system with accessory loads. One of two results will be

displayed.

}PASS

}FAIL

11. Press ENTER when the charging system test is completed. Turn all accessory loads and engine off. Press ENTER

to return to Step 1 or remove the test clamps from the battery posts after completion of testing to end test.

8 Glossary

Gelled Electrolyte (GEL) Battery

A lead-acid electric storage battery that:

}Is sealed using special pressure valves and should never be opened.

}Is completely maintenance-free. (However, connections must be retorqued and the battery cleaned periodically.)

}Uses thixotropic gelled electrolyte.

}Uses a recombination reaction to prevent the escape of hydrogen and oxygen gases normally lost in a flooded

lead-acid battery (particularly in deep-cycle applications).

}Is non-spillable, and therefore can be operated in virtually any position. (However, upside-down installation is

not recommended.)

Absorbent Glass Mat (AGM) Battery

A lead-acid electric storage battery that:

}Is sealed using special pressure valves and should never be opened.

}Is completely maintenance-free. (However, connections must be retorqued and the battery cleaned periodically.)

}Has all of its electrolyte absorbed in separators consisting of a sponge-like mass of matted glass fibers.

}Uses a recombination reaction to prevent the escape of hydrogen and oxygen gases normally lost in a flooded

lead-acid battery (particularly in deep-cycle applications).

}Is non-spillable, and therefore can be operated in virtually any position. (However, upside-down installation is

notrecommended.)

Valve Regulated Lead Acid (VRLA) Battery

A battery that is sealed Maintenance Free with a “Bunce” Valve or Valves in the top that opens when a preset pres-

sure is realized inside the battery and lets the excess gas pressure out. Then the valve resets itself.

Example

en |8|Operating Instructions | BAT 135 Battery Tester

BAT 135 | REV. A | JANUARY 2018

Starting, Lighting, Ignition (SLI) Battery

A battery that performs three basic functions on all normal vehicles. Batteries given this description will have been

specifically designed for service on cars and trucks within a voltage controlled electrical system. Those SLI batteries

which are intended for heavy haulage vehicles fitted with large diesel motors may often be called COMMERCIAL

batteries. They have to be much more powerful and more robust than batteries intended for cars.

State of Health (SOH)

Percent of battery capacity remaining compared with the marked original battery capacity.

State of Charge (SOC)

Percent of battery actually charged.

Cold Cranking Amps (CCA)

The current in amperes which a new fully charged battery can deliver for 30 seconds continuously without the termi-

nal voltage falling below 1.2 volts per cell, after it has been cooled to 0 degrees F and held at that temperature. This

rating reflects the ability of the battery to deliver engine starting currents under winter conditions.

Ampere-Hour

The unit of measurement of electrical capacity. A current of one ampere for one hour implies the delivery or receipt

of one ampere-hour of electricity. Current multiplied by time in hours equals ampere-hours.

9 Warranty Terms and Conditions

Any battery tester found defective in material or workmanship within one year from the date of purchase by a retail

customer will be repaired or replaced according to published defective return test repair procedures. The existence

of a defect shall be determined by the manufacturer in accordance with published warranty repair procedures. The

warranty repair procedures are available upon request.

This warranty does not cover any unit that has been damaged due to accident, abuse, alternation, use for a purpose

other than that for which it was intended, or failure to follow operating instructions. This warranty is expressly

limited to original retail buyers. This warranty is not assignable or transferable. Proof of purchase is required for all

alleged claims. Warranty cannot be authorized without proof of purchase. Warranty claims must be sent pre-paid

with dated proof of purchase. Damage incurred during shipment is the responsibility of the shipper (customer

returning unit) If the returned unit qualifies for warranty, the shipper will only incur shipping cost. The manufacturer

reserves the right to substitute or offer alternative warranty options at its discretion.

The sole and exclusive remedy for any unit found to be defective is repair or replacement, at the option of the manu-

facturer. In no event shall the manufacturer be liable for any direct, indirect, special, incidental, or consequential

damages (including lost profit) whether based on warranty, contract, tort, or any other legal theory.

Return Goods

Pack with sufficient over-pack to prevent damage during shipment. Damage incurred during return shipment is not

covered under this warranty. Repair costs for such damages will be charged back to shipper.

WHEN RETURNING GOODS, PLEASE INDICATE “RETURN GOODS” ON ALL INVOICES AND

RELATED SHIPPING DOCUMENTS TO PREVENT ANY EXTRA CHARGE.

BAT 135 | REV. A | JANUARY 2018

Operating Instructions | BAT 135 Battery Tester | 9|en

Appendix A System Analyzer Screens

The following screens are available for system analysis, testing, and customization.

Note: Current language is displayed initially.

Language

en |10 |Operating Instructions | BAT 135 Battery Tester

BAT 135 | REV. A | JANUARY 2018

Appendix B Surface Charge Notice

The battery will hold a surface charge if the engine has been running or after the battery has been charged. The

tester may prompt you to remove the surface charge. Follow the instructions indicating when to turn the headlights

on and off or apply a load into the battery.

In Vehicle

Out of Vehicle

The tester will resume testing after it detects that the surface charge is removed.

1. Test the battery for a few seconds.

2. Press to select battery fully charged or not if tester asks, then press ENTER to confirm choice.

3. When the test is completed, the display shows the actual volts and the actual SAE or %. Press to select:

}SOH (STATE OF HEALTH)

}SOC (STATE OF CHARGE)

One of 6 results will be displayed.

Good & Pass

The battery is good and capable of holding a charge.

Marginal Battery

A Marginal battery indicates that your battery is functioning properly, but its life expectancy is compromised.

The battery should be closely monitored with more frequent battery checkups.

Recharge & Retest

The battery is discharged, the battery condition cannot be determined until it is fully charged. Recharge and

retest the battery.

Inhaltsverzeichnis

Andere Bosch Prüfgeräte Handbücher

Bosch

Bosch EPS 807 Einrichtungshandbuch

Bosch

Bosch EL-52425 Bedienungsanleitung

Bosch

Bosch FSA 500 Bedienungsanleitung

Bosch

Bosch KTS 340 Bedienungsanleitung

Bosch

Bosch SDL 43 Series Technische Daten

Bosch

Bosch CRS 845H Benutzerhandbuch

Bosch

Bosch EPS 205 Bedienungsanleitung

Bosch

Bosch MTS 6513 Bedienungsanleitung

Bosch

Bosch CRS 845 Bedienungsanleitung

Bosch

Bosch SCT 141 Series Bedienungsanleitung

Bosch

Bosch EPS 610 Bedienungsanleitung

Bosch

Bosch DCI 700 Bedienungsanleitung

Bosch

Bosch KTS 200 Bedienungsanleitung

Bosch

Bosch Professional GOS 10,8 V-LI Bedienungsanleitung

Bosch

Bosch CAM 847 Technische Daten

Bosch

Bosch EPS 200 Bedienungsanleitung

Bosch

Bosch Denoxtronic 1.1 Technische Daten

Bosch

Bosch HTD 6 Series Bedienungsanleitung

Bosch

Bosch GE-50576-A Bedienungsanleitung

Bosch

Bosch BCT 100 Bedienungsanleitung

Bosch

Bosch EPS 200 Bedienungsanleitung

Bosch

Bosch EPS 118 Bedienungsanleitung

Bosch

Bosch DAS 3000 S20 Bedienungsanleitung

Bosch

Bosch rexroth VT-SVTSY-1 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung