Bouncepad CADDY Bedienungsanleitung

Sheet Code: BP-IM-070_REV2_Combined

Release Date: 18/05/2022

Condential, no part of this publication

may be reproduced or transmitted in any

form without the written permission of the

CADDY

Assembly Instructions

Tools Required to Fix From Below:

Unless specied, instructions are

for both Eddy and Click stands.

Drill

Pencil

5mm Drill Bit

Fixings List

* Due to the modular nature of

our product range you may receive

additional xings in the xings kit

4x M4

wing nut

4x M4 split

washer

4x M4 at

washer

1x tie 4x clips

Fixings Kit

1x Caddy

2x 80mm

grub screw

4x M4

buttonhead

screw

In the Caddy Box

1x Drilling

Template

T20 torx

allen key

Insert the tie through the grill and

then clasp over the device.

2Insert the cable management clips

into the grill, then twist to secure.

3 4 Feed your Eddy/Click charge cable

through the channel.

1Complete separate Eddy

or Click manuals until

steps shown above.

65 Additonal devices are connected

by repeating step 2.

Wrap the charge cable around the

clips and plug into the power source.

tie

clip

full list of

supported devices

available at

bouncepad.com

USB hub or battery pack

Basic setup is now complete. To add

security features follow steps 7 onwards.

* Keep sucient slack

to allow Eddy/Click to

rotate freely.

full list of

supported devices

available at

bouncepad.com

receipt printer

card reader

Eddy manual

Step 6

Click manual

Steps A2+C1

Lift up the Eddy Stand and remove

bungs and OUTER half-bungs from

Caddy.

bung

half-bung

Eddy Only

Screw M4 80mm grubscrews into

Caddy until nger tight.

9 109

Attach 4x M4 buttonhead screws

through the tray and into the stand.

Attach 2x M4 buttonhead screws

through the tray and into the stand.

Lift up the Click Stand and remove

the INNER half-bungs from Caddy.

Buttonhead

Screw

Buttonhead

Screw

80mm

Grubscrew

T20 Pin Torx

Allen Key

T20 Pin Torx

Allen Key

T20 Pin Torx

Allen Key

half-bung

Attach illustrated washers and tighten wingnuts by hand.

Caddy is now securely attached to your surface.

Use a hand drill with 5mm bit to

make holes through your surface.

power drill

14 Insert the assembled product through

the pilot holes.

12 Place the drilling template over the

surface and mark the holes with a

pencil.

pencil

drilling template

M4 at washer

M4 split washer

M4 wing nut

Eddy Only Click OnlyClick Only

Assembly

Complete

Dieses Handbuch passt für folgende Modelle

Andere bouncepad Rack & Stand Handbücher

bouncepad

bouncepad VESA Bedienungsanleitung

bouncepad

bouncepad Wing Bedienungsanleitung

bouncepad

bouncepad Lounge Bedienungsanleitung

bouncepad

bouncepad Wing-Slim Bedienungsanleitung

bouncepad

bouncepad Sumo 270 Degrees Mounting Arm Bedienungsanleitung

bouncepad

bouncepad Wing Bedienungsanleitung

bouncepad

bouncepad Floorstanding Slim Bedienungsanleitung

bouncepad

bouncepad Wallmount Bedienungsanleitung

bouncepad

bouncepad Floorstanding with Brother Printer Mount Bedienungsanleitung

bouncepad

bouncepad Wing Freestanding Bedienungsanleitung

bouncepad

bouncepad Self-Service Mount Bedienungsanleitung

bouncepad

bouncepad Flex Bedienungsanleitung

bouncepad

bouncepad Floorstanding Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung

bouncepad CADDY Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken