Bradley Express MG Series Bedienungsanleitung

215-1480 Rev. G; ECN 13-08-025

Page 1 of 20 4/9/2014

Installation

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 800.BRADLEY (800.272.3539) Fax: 262.253.4161

bradleycorp.com

MG-2/TT

Express®Lavatory

System - MG-Series

with TouchTime®Control

Table of Contents

Pre-Installation Information ..............2

Dimensions..........................3-4

Installation Instructions............... 5-13

Cleaning and Maintenance .............14

Assembly of Components ............15-17

Solenoid Valve Troubleshooting .......18-19

Navigator®Valve Maintenance...........20

IMPORTANT

Read this entire installation manual to ensure proper

installation.

Flush all the water supply lines before making connections.

Wall anchors used must have a minimum pull-out rating of

1,000 lbs.

File these instructions with the owner or maintenance

department.

Product warranties may be found under “Product

Information” on our web site at www.bradleycorp.com.

Express®Lavatory System - MG-Series with TouchTime®Control

MG-2/TT Installation

24/9/2014 Bradley • 215-1480 Rev. G; ECN 13-08-025

Pre-Installation Information

Barrier-free and ADA compliant - standard height mounting

The MG-2/TT Express®Lavatory System must have a rim height no higher than 34" above finished floor to be

compliant with Americans with Disabilities Act (ADA). When mounted at 34" rim height, the MG-2/TT Express®

Lavatory System meets ADA, ANSI and UFAS requirements for barrier-free clearances, reaches and controls.

Always check local codes and ordinances for compliance.

Barrier-free and ADA compliant - juvenile height mounting

The MG-2/TT Express®Lavatory System must have a rim height no higher than 30" above finished floor to

be compliant with Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities:

Building Elements Designed for Children’s Use; Final Rule.

Texas Accessibility Standards compliant:

The MG-2/TT Express®Lavatory System meets Texas Accessibility standards (TAS) for barrier-free

clearances, reaches and controls. Always check local codes and ordinances for compliance.

TouchTime®switch and solenoid

Each sprayhead is controlled by a TouchTime®switch, enabling each user to activate a single flow of water.

Each valve uses less than half the maximum of hot water allowed by the ANSI/ASHRAE/IESNA 90.1-1989

Standard.

Supplies required for installation:

• (8)³⁄₈" wall anchors, bolts and washers to mount frame and bowl to wall

(minimum pull-out rating of 1,000 lbs.)

• ½"Nominalcoppertubingforhotandcoldsuppliesand1½"NPTdrainpiping

• 110voltelectricaloutletfor110/24VACplug-intransformer(supplied)

• 240/208-voltor277-voltelectricaloutletforoptionalelectrictanklesswaterheater

Express®Lavatory System - MG-Series with TouchTime®Control

Installation MG-2/TT

Bradley • 215-1480 Rev. G; ECN 13-08-025 4/9/2014 3

MG-2/TT Express®Lavatory System Dimensions

54"

(1372)

42"

(1067)

15"

(381)

27"

(686)

47"

(1194)

(mm)

*Subtract 4" from vertical dimensions for compliance with ADA guidelines for children’s use.

22"

(559)

*39"

(991)

*33½"

(851)

*29½"

(749)

*17½"

(445)

21½"

(546)

9½"

(241)

(mm)

15"

(381)

Express®Lavatory System - MG-Series with TouchTime®Control

MG-2/TT Installation

44/9/2014 Bradley • 215-1480 Rev. G; ECN 13-08-025

Dimensions continued . . .

TAS Juvenile Height

Grades 6 thru 8 or 9

TAS Juvenile Height

Grades Pre-K thru 5 or 6

37½"

(952)

32"

(813)

28"

(711)

16"

(406)

FLOOR

35½"

(902)

30"

(762)

26"

(660)

14"

(356)

FLOOR

(mm)

Express®Lavatory System - MG-Series with TouchTime®Control

Installation MG-2/TT

Bradley • 215-1480 Rev. G; ECN 13-08-025 4/9/2014 5

Installation Instructions

Step 1: Rough in supplies and optional hot water heater

NOTE: See Figure 1 (below), 1a, 1b (for TAS on page 6) and Figure 2 (on page 7) when roughing

in the MG-2/TT Express®.

IMPORTANT: Flush the supply lines before making connections. Debris in supply lines will cause

the valves to malfunction.

IMPORTANT: Dimensions shown in Figure 1 are for Standard Height Mounted

MG-2/TT Express®.

1. Rough in ½" nominal copper tubing for hot and cold supply lines through wall at dimensions shown.

2. Rough in 1½" NPT drain waste connection through wall at dimensions shown.

3. OPTIONAL HOT WATER HEATER: Rough in appropriate electrical supply per local code (recommended

240/208-volt or 277-volt electrical box location shown below).

(102)

(127)

FLOOR

14"

(356)

14"

(356)

*22³⁄₈"

(568)

*28¼"

(718)

*25¾"

(654)

½" NOMINAL COPPER TUBING

FOR HOT AND COLD SUPPLIES OR

TEMPERED SUPPLY – STUB OUT 2"

³⁄₈" WALL ANCHORS (8) PLACES MIN. PULL-OUT

STRENGTH 1000 LBS. PER ANCHOR

110V GFI

PROTECTED

ELECTRICAL

OUTLET

*Juvenile Height Mounting:

Subtract 4" from vertical dimensions for compliance with ADA guidelines for children’s use.

Figure 1

Standard Height Mounting CENTERLINE

OF FIXTURE

1½" NPT DRAIN

STUB OUT 2"

*24½"

(654)

*26"

(660)

*31½"

(800)

3¾" (95)

*19½"

(495)

(102)

4" (102)RECOMMENDED 240V/208V

OR 277V FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(2½" l x 3" w x 4" h)

RECOMMENDED

240V/208V OR 277V

FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(4" l x 3" w x 4" h)

*23"

(584)

16½"

(419)

APPROX. DIMENSION

25½" (648)

APPROX. DIMENSION

25½" (648)

BBB

Express®Lavatory System - MG-Series with TouchTime®Control

MG-2/TT Installation

64/9/2014 Bradley • 215-1480 Rev. G; ECN 13-08-025

Figure 1a

TAS - Texas Accessibility

Standards:

Juvenile Height (grades

Pre-K thru 5 or 6)

(102)

(127)

FLOOR

14"

(356)

14"

(356)

18⁷⁄₈"

(479)

24¾"

(629)

22¼"

(565)

½" NOMINAL COPPER TUBING FOR HOT AND COLD SUPPLIES OR

TEMPERED SUPPLY – STUB OUT 2"

³⁄₈" WALL ANCHORS (8) PLACES MIN. PULL-OUT STRENGTH 1000 LBS. PER ANCHOR

CENTERLINE OF FIXTURE

1½" NPT DRAIN

STUB OUT 2"

21"

(533)

22½"

(572)

28"

(711)

3¾" (95)

16"

(406)

(102)

4" (102)RECOMMENDED 240V/208V

OR 277V FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(2½" l x 3" w x 4" h)

RECOMMENDED

240V/208V OR 277V

FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(4" l x 3" w x 4" h)

19½"

(495)

16½"

(419)

APPROX. DIMENSION

25½" (648)

APPROX. DIMENSION

25½" (648)

BB B

Figure 1b

TAS - Texas Accessibility

Standards:

Juvenile Height (grades 6

thru 8 or 9)

(102)

(127)

FLOOR

14"

(356)

14"

(356)

26-3/4"

(679)

24-1/4"

(616)

½" NOMINAL COPPER TUBING FOR HOT AND COLD SUPPLIES OR TEMPERED

SUPPLY – STUB OUT 2"

³⁄₈" WALL ANCHORS (8) PLACES MIN. PULL-OUT STRENGTH 1000 LBS. PER ANCHOR

CENTERLINE OF FIXTURE

1½" NPT DRAIN

STUB OUT 2"

23"

(584)

3¾" (95)

18"

(457)

(102)

4" (102)RECOMMENDED 240V/208V

OR 277V FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(2½" l x 3" w x 4" h)

RECOMMENDED

240V/208V OR 277V

FOR OPTIONAL

ELECTRICAL BOX

LOCATION

(4" l x 3" w x 4" h)

21½"

(546)

16-1/2"

(419)

APPROX. DIMENSION

25½" (648)

APPROX. DIMENSION

25½" (648)

BB B

30"

(762)

20⁷⁄₈"

(530)

24½"

(622)

110V GFI

PROTECTED

ELECTRICAL

OUTLET

110V GFI

PROTECTED

ELECTRICAL

OUTLET

Express®Lavatory System - MG-Series with TouchTime®Control

Installation MG-2/TT

Bradley • 215-1480 Rev. G; ECN 13-08-025 4/9/2014 7

Installation Instructions continued . . .

Step 2: Rough in wall anchors and electrical outlet

IMPORTANT: Turn OFF electrical power to the outlet when installing the Express®Lavatory

System.

1. Install a 110 volt GFI protected electrical outlet per local code at the location shown in Figure 2.

2. Install six ³⁄₈" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by installer) at the

locations marked (ref. location “B” shown in Figure 1, 1a or 1b on pages 5-6).

NOTE: The dimensions for the wall anchors at location "A" are for reference only.

3. On the back of the bowl, measure the distance between the ¾" bowl mounting holes. Divide this

measurement in half. Measure and mark this dimension on the wall to the left of the centerline and to the

right of the centerline. Install two ³⁄₈" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by

installer) at the locations marked (ref. location "A" shown in Figure 1, 1a or 1b on pages 5-6).

NOTE: The anchors will be used to mount the Express®MG-2/IR bowl and frame to the wall.

Figure 2

110 VOLT GFCI

ELECTRICAL OUTLET

TRANSFORMER

LOCATION

½" NOMINAL

COPPER TUBING

FOR HOT AND

COLD SUPPLIES OR

TEMPERED SUPPLY.

STUB OUT 2”

1½" NPT DRAIN

STUB OUT 2”

Express®Lavatory System - MG-Series with TouchTime®Control

MG-2/TT Installation

84/9/2014 Bradley • 215-1480 Rev. G; ECN 13-08-025

Installation Instructions continued . . .

Step 3: Mount frame to wall

1. Loosen, but do not remove the three bottom access panel screws.

2. Remove the two top access panel screws and washers securing the access panel to the frame and

remove the access panel (see Figure 3).

3. Position the frame with Terreon®End Caps attached, against the wall, ensuring that it is level.

IMPORTANT: Anchoring the frame to a wall that is not flat may cause the frame to bend. If

necessary, install shims to compensate for wall distortion.

4. Ensure that the back of the frame is flat against the wall. If wall is not flat, insert shims behind the frame

to ensure that it will not bend when anchored.

5. Once you have positioned the frame such that it is level and flat against the wall or shimmed, use the ³⁄₈"

bolts and washers to mount the frame to the wall.

Figure 3

³⁄₈" BOLTS AND WASHERS

(6) PLACES

TERREON®

END CAP

LEFT

STAINLESS STEEL

ACCESS PANEL

TERREON®

END CAP

RIGHT

FRAME

¼" - 20 SCREWS

AND FINISHING

WASHERS

(5) PLACES

FRONT VIEW

Express®Lavatory System - MG-Series with TouchTime®Control

Installation MG-2/TT

Bradley • 215-1480 Rev. G; ECN 13-08-025 4/9/2014 9

Installation Instructions continued . . .

Step 4: Install bowl assembly

IMPORTANT: See Figure 4 below when installing the bowl assembly. If the fixture has soap option,

refer to the soap installation manual 215-1585 before installing the bowl assembly.

1. With someone to assist you, place the bowl assembly squarely onto the frame being careful not to pinch

tubing between bowl and frame.

2. Attachthefrontofthebowlassemblytotheframeusingthetwo¼-20x½"pan-head

screws and washers provided. Do not tighten screws at this time.

IMPORTANT: When bolting the bowl assembly to the wall, do not overtighten the bolts.

Overtightening bolts can damage the Terreon®material.

3. After the bowl assembly is attached to the frame, install the two ³⁄₈" bolts and washers

(supplied by the installer) to bolt the bowl to the wall anchors. Do not overtighten bolts.

4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame.

Do not overtighten.

5. If necessary, adjust sprayhead body to fit closely to wall by adjusting sprayhead mounting bolts. See

Figure 8 on page 14 for sprayhead mounting bolt locations.

Figure 4

³⁄₈" BOLT

AND WASHER

TERREON®

END CAP (R) TERREON®

END CAP (L)

FRAME SPRAYHEAD

³⁄₈" BOLT

AND WASHER

BOWL

¼"-20 x ½"

PAN HEAD

SCREWS AND

WASHERS

(2) PLACES

BACK VIEW

Express®Lavatory System - MG-Series with TouchTime®Control

MG-2/TT Installation

10 4/9/2014 Bradley • 215-1480 Rev. G; ECN 13-08-025

Installation Instructions continued . . .

Step 5: Connecting supply

1. Loosen but do not remove the two mounting screws holding the valve bracket to the frame. Slide the

valve bracket up until the larger cutout in the frame’s slot aligns with the screw head (see Figure 5b).

Then lift up to remove the valve bracket from the frame.

2 FOR HOT AND COLD SUPPLY: Attach the stops to the hot and cold water supply piping from the wall.

Connect the flexible hoses to the Navigator Mixing Valve and to the stops (see Figure 5a).

NOTE: The “H” on Navigator Mixing Valve indicates hot water supply inlet.

 FORSINGLETEMPEREDSUPPLY:Attachthestoptothe½"temperedsupplyline.Connectthestopto

the tempered line adapter with the flexible supply hose (Figure 5c).

3. AssembletheP-trapbyconnectingthe1½"tubularpipetothetailpieceandtothe1½"drainpipestubbed

out of the wall.

4. Install the strainer on the drain plug opening inside the bowl, and push the strainer firmly into place.

Secure the stainer with the screw provided.

Figure 5a FLEXIBLE SUPPLY

HOSE

NAVIGATOR

THERMOSTATIC

MIXING VALVE

FLEXIBLE

SUPPLY

HOSE

CONNECT TO

HOT WATER

SUPPLY

CONNECT TO

COLD WATER

SUPPLY

Figure 5c

FLEXIBLE

SUPPLY HOSE

(TO SOLENOID

BRACKET)

TO SUPPLY LINE

TEMPERED

LINE ADAPTER

(S39-804)

Hot and

Cold

Supplies

Single

Tempered

Supply

Figure 5b

SLOT IN

FRAME

VALVE BRACKET

MOUNTING SCREW

Andere Handbücher für Express MG Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Badezimmerarmatur Handbücher

Bradley

Bradley 5600 Series Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley s19314 series Bedienungsanleitung

Bradley

Bradley HN300 Bedienungsanleitung

Bradley

Bradley Verge LVA Series Bedienungsanleitung

Bradley

Bradley SA70 Series Bedienungsanleitung

Bradley

Bradley 400 Series Bedienungsanleitung

Bradley

Bradley S19-110HFP Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley HSC79 Bedienungsanleitung

Bradley

Bradley Express EXD Series Bedienungsanleitung

Bradley

Bradley Verge LVLD Series Bedienungsanleitung

Bradley

Bradley S19-120HFP Bedienungsanleitung

Bradley

Bradley LVA Series Bedienungsanleitung

Bradley

Bradley LC700 Bedienungsanleitung

Bradley

Bradley S19-300T Bedienungsanleitung

Bradley

Bradley S19-310TW8 Bedienungsanleitung

Bradley

Bradley SN2005/TT Bedienungsanleitung

Bradley

Bradley Halo S19314EW Bedienungsanleitung

Bradley

Bradley WS-3WMT Bedienungsanleitung

Bradley

Bradley WF2705 Bedienungsanleitung

Bradley

Bradley Terreon Deep Bowl TDB3100 Series Bedienungsanleitung

Bradley

Bradley S19-310SS Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Beliebte Badezimmerarmatur Handbücher anderer Marken

DURAVIT

DURAVIT C.1 C15240 0090 Handbuch

Sunshower

Sunshower PURE SOLO Bedienungsanleitung

Heatstore

Heatstore HSTRL500WTN Bedienungsanleitung

Delabie

Delabie Delabie Sporting 714700 Bedienungsanleitung

Kohler

Kohler K-13056 Montageanleitung

ESS

ESS Container TCL-11 Bedienungsanleitung

Mustee

Mustee 22C Bedienungsanleitung

VITRA

VITRA V-Flow Bedienungsanleitung

Malmet

Malmet B105BT Bedienungsanleitung

bathstore

bathstore Transition H1690MM Leitfaden

baliv

baliv DUK-80.30 T Bedienungsanleitung

baliv

baliv DU-5160 Bedienungsanleitung

BELLOSTA

BELLOSTA Edward 0800/M Bedienungsanleitung

Franke

Franke PRTR0006 Bedienungsanleitung

Gessi

Gessi RILIEVO 59011 Bedienungsanleitung

noken

noken VITAE 100188525-N299998810 Bedienungsanleitung

Allen + Roth

Allen + Roth 1142VA-30-201 Bedienungsanleitung

Britex

Britex HBDA Bedienungsanleitung