Bradley Express SS Series Bedienungsanleitung

Installation

P.O. Box 309

Menomonee Falls, WI 53052 USA

800 BRADLEY (800 272 3539)

+1 262 251 6000

bradleycorp.com

SS-3N Infrared

(Standard and Wall-Hung)

Express®Lavatory System SS-Series

Table of Contents

Pre-Installation Information................................................2

Components ......................................................................3

Supplies Required .............................................................4

Dimensions....................................................................4–5

Rough-Ins ..........................................................................6

Mount Frame to Wall .........................................................7

Install Bowl ........................................................................7

Connect the Supply ...........................................................8

Install Drains......................................................................9

Connect Electrical and Sprayhead Supplies .....................9

Adjust Temperature..........................................................10

Sensor Assembly and Solenoid Valve Access ................10

Solenoid Valve Troubleshooting.......................................11

Navigator® Mixing Valve Troubleshooting .......................12

Stop Valve Troubleshooting .............................................13

Cleaning and Maintenance for Terreon®.........................13

Soap Dispenser Maintenance .........................................14

Express Lavatory Systems are ADA and TAS compliant

U.S. Pat. Nos. 5,611,093, 5,369,818, D398,969

Other Patents Pending

215-1493 Rev. K; ECN 17-08-010

Page 1 of 14 5/18/2017

SS-3N with infrared activation, standard

frame and liquid soap dispenser

SS-3N with infrared activation, wall-hung

frame and liquid soap dispenser

SS-3N Installation

25/18/2017 Bradley • 215-1493 Rev. K; ECN 17-08-010

Special Note for Sprayhead/Bowl retrofit

to retrofit new SS-3N sprayhead onto existing SS-3 bowl

1½" (38mm)

Drill hole Ø 1" (25mm)

to 1½" (38mm).

Existing Hole

2¼" (57mm)

WARNING

Make sure that all water supply lines have been flushed and then completely turned off before beginning

installation. Debris in supply lines can cause valves to malfunction.

Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation. Electrical

power MUST remain off until installation is complete. After installation is complete, turn on the water supply

first, then turn on the electrical power.

Hardware supplied by installer must be appropriate for wall construction. Wall anchors must have a

minimum pull-out rating of 1,000 lbs. Follow appropriate dimensions for standard or juvenile height based on

configuration and required rim height. Overtightening fasteners can damage the Terreon® material. Use caution

when tightening bowl and sprayhead fasteners.

IMPORTANT

Read this entire installation manual to ensure proper installation. When finished with the installation, file this

manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances

is the responsibility of the installer. Product warranties may be found under "Products" on our Web site at

www.bradleycorp.com.

Separate parts from packaging and make sure all parts are accounted for before discarding any packaging

material. If any parts are missing, do not begin installation until you obtain the missing parts.

Installation SS-3N

Bradley • 215-1493 Rev. K; ECN 17-08-010 5/18/2017 3

Components

Power Adapter

(261-147A)

Sprayhead Cover

(SS-3N-COVR-ONLY)

Contact your local Bradley Rep for part number.

Sprayhead Body

(SS-3N-SPYD-ASSY)

Contact your local Bradley

Rep for part number.

Bowl

(SS-3N-BOWL)

Contact your local Bradley

Rep for part number.

Washer

(142-002BJ)

LockWasher

(142-002BK)

Nut, 5/16-18

(161-036)

Main Frame

(S17-323)

Pedestal Panel, Coal

(186-1454B)

Panel Fasteners (160-450)

Washers (142-002CA)

(8) Places

Screw, 10-24

(160-386)

Bolt, 5/16-18

(160-371)

Polypropylene P-Trap

(269-1697)

Optional Chrome Plated Brass

P-Trap (S29-094)

Waste Tee

(111-063)

Waste Shoe

(111-062)

1/8" Rubber Washer

(125-001DP)

Drain Plug

(P16-072)

Strainer

(P16-075)

#8-32 Screw

(160-319)

Drain Assembly

Bowl Mounting

Hardware

1/4"-20 x 1/2" Pan

Head Screw (Qty 4)

(160-389)

1/4"-20 Washer

(Qty 4)

(142-002DB)

Scuff Base Panel,

Coal (185-033B)

Scuff Panel Fasteners

(160-450)

Washers (142-002CA)

(4) Places)

Scuff Base (17-324)

(used with standard

height frame only)

SS-3N Installation

45/18/2017 Bradley • 215-1493 Rev. K; ECN 17-08-010

Supplies Required

• (8) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount main frame and bowl to wall (minimum pull-out rating

of 1,000 lbs.)

• STD. HEIGHT ONLY: (2) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount scuff base to wall

• 1/2" nominal copper tubing for hot and cold supplies and 1-1/2" NPT drain piping

• 120V/220V 50/60 Hz power source using Bradley supplied 120VAC/12V DC plug in adapter

Dimensions - Front and Top Views

SOAP

SOAP SOAP

SOAP

Top View 80"

(2032)

Front View

Standard Frame

Front View

Wall-Hung Frame

8-5/8" (219)

30"

(762)

(203)

51-1/4" (1302)

58" (1473)

64" (1626)

68-1/4" (1734)

8" (203)

68-1/4"

(1734)

58" (1473)

64" (1626)

8" (203) Radius 10" (254) Radius

30"

(762)

(mm)

Installation SS-3N

Bradley • 215-1493 Rev. K; ECN 17-08-010 5/18/2017 5

Dimensions - Side Views

TAS

Wall Hung Mounted

at Standard Height

Standard

Height

Wall Hung Mounted

at Juvenile Height

Ages: 6 through 12

Wall Hung Mounted

at TAS Height

Grades: 6

through

8 or 9

Wall Hung Mounted

at TAS Height

Grades: Pre-K

through 5 or 6

21-1/8"

(537)

38-1/2"

(978)

34"

(864)

30"

(762)

13-1/4"

(311)

11-1/2"

(292)

Scuff Base on

Standard Height Only

3" (76)

8-5/8"

(219)

21-1/8" (537)

11-1/2"

(292)

(mm)

38-1/2"

(978)

34"

(864)

30"

(762)

13-1/4"

(311)

8-5/8"

(219)

21-1/8"

(537)

11-1/2"

(292)

8-5/8"

(219)

35-1/2"

(902)

31"

(787)

27"

(686)

10-1/4"

(260)

21-1/8"

(537)

11-1/2"

(292)

8-5/8"

(219)

36-1/2"

(927)

32"

(813)

28"

(711)

11-1/4"

(286)

21-1/8"

(537)

11-1/2"

(292)

8-5/8"

(219)

34-1/2"

(876) 30"

(762)

26"

(660)

9-1/4"

(235)

SS-3N Installation

65/18/2017 Bradley • 215-1493 Rev. K; ECN 17-08-010

CODE DESCRIPTION QTY.

A 3/8" Wall Anchors with a minimum pull-out force of 1,000 lbs. for Bowl 2

B 3/8" Wall Anchors with a minimum pull-out force of 1,000 lbs. for Mainframe 6

C3/8" Wall Anchors for Base Frame, Standard Frame option only, minimum pull-out force not

required 2

D1 1/2" nominal copper tubing for Cold Supply, stub-out 2" from wall 1

D2 1/2" nominal copper tubing for Hot or Tempered Supply, stub-out 2" from wall 1

E 1-1/2" NPT Drain, stub-out 2" from wall 2

On the bowl back, measure the distance between the 3/4" bowl mounting holes. Divide this

measurement in half. Measure and mark this dimension on the wall to the left and the right

of the centerline. Install two 3/8" wall anchors with a minimum pull-out rating of 1,000 lbs

(supplied by installer) at locations marked.

J 110v GFI Protected Electrical Outlet 1

RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FOR

CODES A–E, H, C and W FIXTURE STYLE

34" None Standard Height

34" None Wall-Hung

32" Subtract 2" TAS, Grades 6 through 8 or 9

31" Subtract 3" Juvenile Height

30" Subtract 4" TAS, Pre-K through Grades 5 or 6

Rough-Ins

38-1/2"

(978)

38-1/2"

(978)

24-3/8"

(619)

24-3/8"

(619)

13"

(330)

(203)

(102)

2-3/4"

(70)

32"

(813)

28-3/4"

(720)

15"

(381)

3-1/2"

(89)

24"

(610) 5-5/8"

(143)

Floor

A, F

D1 D2 E

A, F

34"

(864)

Rim

Height

See

Chart

Below

Installation SS-3N

Bradley • 215-1493 Rev. K; ECN 17-08-010 5/18/2017 7

Anchoring the frame to a wall that is not flat may

cause the frame to bend, making it difficult to

reinstall the access panels. If necessary, use

shims to compensate for wall distortion.

The sprayhead body has slotted holes for adjusting the fit-up with the

bowl and wall.

For clarity, the scuff base frame and drain are not shown. Turn the

tailpiece down to its proper position before installing the bowl.

Mount Frame to Wall

Using a T20 torx key, remove the

fasteners securing the access

panel to the main frame, and

remove the panel.

Once the frame is level and flat against

the wall or shimmed, mount the frame

to the wall at six places using 3/8"

bolts and 1" min. O.D. washers.

When mounting the standard height frame,

mount the scuff base to the wall at the same

time using two additional 3/8" bolts and washers.

Install Bowl

Attach the bowl to the frame with

1/4"-20 x 1/2" pan-head screws

and washers. Do not tighten.

Tighten the pan-head screws.

DO NOT OVERTIGHTEN.

Secure the bowl to

the wall anchors

with 3/8" bolts

and 1" min. O.D.

washers, two

places. Do not

overtighten.

SS-3N Installation

85/18/2017 Bradley • 215-1493 Rev. K; ECN 17-08-010

The letter “H” on the Navigator Mixing

Valve indicates hot water supply inlet.

Connect the Supply - Hot and Cold Supply

Loosen but do not remove the two

mounting screws holding the valve

bracket to the frame.

Slide the valve bracket up and lift it

from the frame.

Connect one end of each hose to

the Navigator valve (one on the hot

side, one on the cold side).

Connect the other swivel end to the

stop valves.

Attach the stops to the hot and

cold water wall stub-outs.

Connect the Supply - Single Tempered Supply

Loosen but do not remove the two

mounting screws holding the valve

bracket to the frame.

Slide the valve bracket up and lift it

from the frame.

Connect one end of flexible hose

to the tempered line adapter.

Connect the other swivel end to

the stop valve.

Attach the stop to the tempered

wall stub-out.

Installation SS-3N

Bradley • 215-1493 Rev. K; ECN 17-08-010 5/18/2017 9

Install the Drains

To Drain

Stub-Out

Connect Electrical and Sprayhead Supplies

WARNING The Express activation must be connected with the 120VAC/12V DC plug-in adapter provided.

Not using the provided adapter can cause personal injury and will result in damage to the

electronics.

Snap each sensor circuit plug into the

associated solenoid circuit plug located on

the valve bracket.

Snap the wall adapter barrel plug into the

barrel plug located on the valve bracket

wire harness.

Supply Inlet

Compression

Nut

(110-231)

Black Supply Tube

(From Sprayhead)

Green Supply Tube

(From Sprayhead)

Red Supply

Tube (From

Sprayhead)

Navigator Thermostatic

Mixing Valve

Loosen the compression nuts.

Push the sprayhead supply tubes firmly into the

tube connectors until they are fully seated.

Tighten the compression nuts by hand.

SS-3N Installation

10 5/18/2017 Bradley • 215-1493 Rev. K; ECN 17-08-010

Sprayhead

Components Infrared Sensor

269-1608HP-DC

Sensor Assembly and Solenoid Valve Access

To access sensors:

1. Remove the Phillips-head screws located in the bottom of the sprayhead body.

2. Lift the Terreon cover/shelf off.

To reinstall sprayhead cover/shelf:

1. Position the cover/shelf on the sprayhead body.

2. Secure it to the sprayhead body using the screws provided.

Window

(269-1241)

O-Ring

(125-157)

Aerator Assembly

(S05-180)

Nut, ½"-14 NSPM

(110-115)

Adjust the Temperature

ALoosen Cap Screw about 1/4" (4-6

turns) and lift up cover (do not

remove).

BUsing cover, turn cartridge gently until

desired water temperature is reached.

Do not turn past stops as this may

damage unit. Push cover down and

tighten screw.

WARNING This valve is NOT factory

preset. Upon installation,

the temperature of this

valve must be checked and

adjusted to ensure delivery

of a safe water temperature.

Water in excess of 110°F

(43°C) may cause scalding.

Reinstall the valve bracket. Turn on the water supply and check for leaks. Turn on the

electrical power to the electrical outlet and pass your hand in front of each station’s

sensor until all the air is purged from the lines and water is ﬂowing smoothly. Reinstall the

access panel.

Wait two full minutes after making the power connection before using the lav. The

sensors will take up to eight full minutes (while not in use) to adapt to the bowl if

another object is detected during the two-minute start-up period.

Andere Handbücher für Express SS Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Badezimmerarmatur Handbücher

Bradley

Bradley S19-310SPR Bedienungsanleitung

Bradley

Bradley Terreon Deep Bowl TDB3100 Series Bedienungsanleitung

Bradley

Bradley HN-200 Bedienungsanleitung

Bradley

Bradley S19-110HFP Bedienungsanleitung

Bradley

Bradley Bradmar 700 Series Bedienungsanleitung

Bradley

Bradley S19-304C2 Bedienungsanleitung

Bradley

Bradley S19-130BF Bedienungsanleitung

Bradley

Bradley S19-120T Bedienungsanleitung

Bradley

Bradley TouchTime 1C Bedienungsanleitung

Bradley

Bradley HSR20 Bedienungsanleitung

Bradley

Bradley Verge LVS Series Bedienungsanleitung

Bradley

Bradley E19-130 Bedienungsanleitung

Bradley

Bradley SXWS9561 Bedienungsanleitung

Bradley

Bradley S19-270HD Bedienungsanleitung

Bradley

Bradley S19-110BF Bedienungsanleitung

Bradley

Bradley OmniDeck with WashBar 5000 Series Bedienungsanleitung

Bradley

Bradley S19-130SS Bedienungsanleitung

Bradley

Bradley S19-125BF Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley 5600 Series Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley S19-280D Bedienungsanleitung

Bradley

Bradley 500 Series Bedienungsanleitung

Bradley

Bradley S19-310TW8 Bedienungsanleitung

Beliebte Badezimmerarmatur Handbücher anderer Marken

DURAVIT

DURAVIT C.1 C15240 0090 Handbuch

Sunshower

Sunshower PURE SOLO Bedienungsanleitung

Heatstore

Heatstore HSTRL500WTN Bedienungsanleitung

Delabie

Delabie Delabie Sporting 714700 Bedienungsanleitung

Kohler

Kohler K-13056 Montageanleitung

ESS

ESS Container TCL-11 Bedienungsanleitung

Mustee

Mustee 22C Bedienungsanleitung

VITRA

VITRA V-Flow Bedienungsanleitung

Malmet

Malmet B105BT Bedienungsanleitung

bathstore

bathstore Transition H1690MM Leitfaden

baliv

baliv DUK-80.30 T Bedienungsanleitung

baliv

baliv DU-5160 Bedienungsanleitung

BELLOSTA

BELLOSTA Edward 0800/M Bedienungsanleitung

Franke

Franke PRTR0006 Bedienungsanleitung

Gessi

Gessi RILIEVO 59011 Bedienungsanleitung

noken

noken VITAE 100188525-N299998810 Bedienungsanleitung

Allen + Roth

Allen + Roth 1142VA-30-201 Bedienungsanleitung

Britex

Britex HBDA Bedienungsanleitung