Bradley FLOAT Series Bedienungsanleitung

Installation

P.O. Box 309

Menomonee Falls, WI 53052 USA

800 BRADLEY (800 272 3539)

+1 262 251 6000

bradleycorp.com

AD3-FLOAT_Install Rev. A

Page 1 of 20 12/10/2021

Euro Style Restroom Partitions

Phenolic LT – FLOAT Series

Table of Contents

Safety Information ...........................2

Supplies Required ...........................2

Marking & Installing U-Brackets.................3

Making Notches (if necessary) .................4

Installing U-Bracket on Middle Pilasters ..........6

Mounting Middle Pilaster to Partition Panel........7

Assembling the Feet .........................9

Mounting the Wall Brackets ...................10

Installing Middle Panel & Side Panel............11

Installing Headrail ..........................12

Installing Doors ............................13

Aligning the System.........................13

Pre-Drilling the System ......................14

Mounting Headrail ..........................15

Riveting Wall Connections ....................16

Mounting Door Latches ......................17

Mounting Hooks & Bumpers ..................18

Appendix A: LED Occupancy Indicator ..........20

Read the instructions in this manual before beginning installation. Save these instructions

and refer to them for inspection, maintenance, and troubleshooting information.

For questions regarding the operation, installation or maintenance of this product, visit bradleycorp.com

or call 800.BRADLEY (800.272.3539).

Product warranties and parts information may also be found under “Resources” on our website at bradleycorp.com.

Euro Style Restroom Partitions, Phenolic LT — FLOAT Series Installation

12/10/2021 Bradley • AD3-FLOAT_Install Rev. A

Supplies Required

• Chalk line and pencil

• 4D laser level

• Power drill or screw gun with drill bit extension

• Miter saw with aluminum saw blade

• Circular saw or jigsaw

• Cordless screwdriver

• Power rivet gun

• Metric tape measure (recommend a wood folding metric ruler)

• Standard hand tools

• Metric HSS drill bits (8 mm, 5 mm, 4.2 mm)

• Scissor jacks

• Rubber mallet

• HB45 construction adhesive

Safety Information

Warning

Before beginning installation, make sure that the wall and floor backing are adequate to support the mounting of the toilet

compartment units.

Partitions are extremely heavy and may require more than one person to position and install.

Failure to comply with these instructions may result in personal injury and/or property damage and will void the warranty.

Caution

Personal protective equipment (PPE) is required during the installation and maintenance of this product.

Notice

To prevent warping, always lay the material flat. Do not lean the material against the wall or stack unevenly.

Make sure all floors and walls are clean and smooth. Remove loose impediments, such as protruding nails and other debris which

could affect installation.

To minimize break-out, always use a support block when drilling through the material.

Carefully remove components from skid, do not drag.

Important

Review your partition layout drawings and verify the number of stalls and components before beginning installation.

Read this installation manual completely to ensure proper installation, then file it with the owner or maintenance department.

This installation manual provides instruction for the assembly of normal partition configurations and standard components.

Non-standard configurations or components including but not limited to curved or angled walls, partial walls, oversized panels, or

modified hardware are not covered in this manual. Compliance and conformity to local codes and ordinances is the responsibility

of the installer.

Separate parts from packaging and make sure all parts are accounted for before discarding packaging material. If any parts are

missing, do not begin installation until you obtain the missing parts.

Installation Euro Style Restroom Partitions, Phenolic LT — FLOAT Series

Bradley • AD3-FLOAT_Install Rev. A 12/10/2021

When installing the partition components, consult the

applicable Bradley Partition submittal drawing speciﬁc to this

job for compartment layout dimensions.

If the centerline dimensions are not speciﬁed, the

cubicle is divided equally according to the dimensions

for the front side.

1Marking & Installing U-Brackets

From the accompanying production drawing, use the

centerline plus overall dimensions and the dimensions

of the front wall. Transfer these measurements to the

ﬂoor and appropriate walls.

Be aware of your surroundings and avoid obstructions.

Number the wall U-brackets while laying out the stalls.

Use the laser level to locate the drill points for each

U-bracket. Mark and then drill the locations.

Using the 4D laser level, locate the centerline of each

U-bracket. Measure up from the ﬂoor 100 mm and

mark the bottom of the ﬁrst U-bracket. Use the ﬁrst

bracket base location as a guide to locate and mark the

remaining bracket locations using the laser level.

Mark the drill holes for the wall connection U-brackets.

Hold the numbered brackets at these locations, line up

the U-bracket pre-drilled holes at laser centerline, and

mark the screw hole locations on the wall. Be sure to

keep the numbered brackets straight.

Drill the marked holes using an 8 mm drill bit, and

then mount the U-brackets using 8 mm x 51 mm

plastic anchors and 5.5 mm x 60 mm countersunk

screws with 6.4 mm washers.

The dimensions from the ﬂoor for the remaining

U-brackets may vary depending on any slope in the

ﬂoor.

Euro Style Restroom Partitions, Phenolic LT — FLOAT Series Installation

12/10/2021 Bradley • AD3-FLOAT_Install Rev. A

2Making Notches (if necessary)

This step may not be necessary, depending on the layout.

Determine whether the shelf is at a right angle.

If several notches are required, align the height of the

U-brackets using a laser level.

Measure the height of the shelf on the back wall and

subtract the specified ground clearance at that location

from this dimension.

Shorten the mitered pre-cut U-bracket to the correct

size. Place the U-bracket with the miter end up,

making sure that it is flush with the top of the shelf.

Adjust the remaining piece of the long U-bracket to the

height of the system, and then attach the U-bracket,

setting it perpendicular to the wall.

Transfer the notch dimension with the addition of

0.20" clearance to the partition panel, and then use a

circular saw to make the notch.

Adjust the short miter U-bracket, and then attach it to

the shelf.

Installation Euro Style Restroom Partitions, Phenolic LT — FLOAT Series

Bradley • AD3-FLOAT_Install Rev. A 12/10/2021

Place the partition panel into the notched brackets.

Level and use jacks to support the panel and to hold the

panel in place.

Euro Style Restroom Partitions, Phenolic LT — FLOAT Series Installation

12/10/2021 Bradley • AD3-FLOAT_Install Rev. A

3Installing U-Bracket on Middle Pilasters

Verify the correct pilasters are selected by matching

the label on the pilasters with what is indicated on the

submittal drawings.

Pay close attention to the latch side versus hinge side,

in addition to the in-swing or out-swing.

Determine the centerline of the pilaster and then draw

a full-length line along the pilaster. There may be a

custom dimension indicated on the submittal drawing.

Place the U-bracket on the interior pilaster flush with

the bottom, and then mark the drill holes.

Using a 4.2 mm drill bit, drill the holes through the

surface of the first panel only, and then attach the

U-bracket using 5.5 mm x 25 mm pan head screws.

Make sure the lower hole catches part of the interior

aluminum frame at the bottom edge of the pilaster.

Installation Euro Style Restroom Partitions, Phenolic LT — FLOAT Series

Bradley • AD3-FLOAT_Install Rev. A 12/10/2021

4Mounting Middle Pilaster to Partition Panel

Position the partition panel on its rear edge.

Install the middle pilaster with profile in the front

groove of the partition panel.

Using the T-connector as a template, mark the drill

holes on the bottom edge of the middle pilaster.

Using a 4.2 mm drill bit, pre-drill the marked holes.

Secure the T-connector to the partition panel

and middle pilaster using three 4.8 mm x 50 mm

countersunk screws.

Put silicone on the interior of the middle pilaster.

Be sure to use padding to protect the edge of the

partition panel when placing it on its edge.

When securing the T-connector, be sure the middle

pilaster is at an exact 90° angle to the partition panel.

Euro Style Restroom Partitions, Phenolic LT — FLOAT Series Installation

12/10/2021 Bradley • AD3-FLOAT_Install Rev. A

Mark the drill holes for the top brackets. Place the

brackets flush with the lower edge of the retaining

block.

Using a 4.2 mm drill bit, pre-drill holes through the first

panel only.

Tightly secure the heavy brackets (105/60/30/8) using

4.8 x 32 mm countersunk screws.

Place the upper retaining heavy block against the

brackets and push onto the upper edge of the

middle panel, and then secure the block using a

4.8 mm x 70 mm countersunk screw.

L-bracket holes are offset so the screws do not

interfere with each other.

Installation Euro Style Restroom Partitions, Phenolic LT — FLOAT Series

Bradley • AD3-FLOAT_Install Rev. A 12/10/2021

5Assembling the Feet

Insert the foot through the lower heavy U-bracket.

Place the heavy U-bracket with foot into the foot drill

hole located in the partition panel.

Use a rubber mallet to tap the foot further into the drill

hole.

Be sure to place loose escutcheon above the ﬂange

of the foot.

Euro Style Restroom Partitions, Phenolic LT — FLOAT Series Installation

12/10/2021 Bradley • AD3-FLOAT_Install Rev. A

6Mounting the Wall Brackets

Temporarily place the end pilaster into the U-bracket.

Mark drill holes for the wall bracket.

Drill the marked holes using an 8 mm drill bit.

Insert the 8 mm x 51 mm plastic anchors into the

pre-drilled holes for the wall brackets.

Tightly secure the brackets with the 5.5 mm x 60 mm

countersunk screws.

Inhaltsverzeichnis

Andere Bradley Inneneinrichtung Handbücher

Bradley

Bradley 964-000000 Bedienungsanleitung

Bradley

Bradley SIMPLE FRENCH Bedienungsanleitung

Bradley

Bradley Lenox Bedienungsanleitung

Bradley

Bradley Lenox Bedienungsanleitung

Bradley

Bradley 227 Towel Dispenser Bedienungsanleitung

Bradley

Bradley 400 Series Bedienungsanleitung

Bradley

Bradley Bradmar 700 Series Bedienungsanleitung

Bradley

Bradley Bradmar 400 Series Bedienungsanleitung

Bradley

Bradley Lenox Lockers LENOXPEDESTAL Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung