Branick 7600 Gebrauchs- und Pflegehandbuch

Branick Industries, Inc. •4245 Main Avenue •Fargo, North Dakota 58103

REV042418 P/N: 81-0246B

Installation, Operation

& Repair Parts

Information

MODEL 7600

STRUT SPRING

COMPRESSOR

TABLE OF CONTENTS _______________________________________________________

SAFETY INSTRUCTIONS 1

DEFINITIONS 1

SPECIFICATIONS 2

INSTALLATION INSTRUCTIONS 2

OPERATING INSTRUCTIONS 3

Positioning the Strut Assembly 3

Disassembly 6

Reassembly 7

MAINTENANCE 8

REPAIR PARTS 9

WARRANTY 11

SAFETY INSTRUCTIONS _____________________________________________________

•NEVER allow unauthorized personnel to operate this product.

•NEVER use this product for anything other than its intended use.

•THOROUGHLY train new employees in the proper use and care of this product.

•PROHIBIT unauthorized personnel from being in shop area while this product is in use.

DEFINITIONS _______________________________________________________________

•CAUTION: Indicates a potentially hazardous situation, which if not avoided, may result in damage to

property or minor personal injury.

•HAZARD: A source of potential injury to a person.

•MAINTENANCE: Those actions that preserve the correct and proper conditions under which the machine

shall be used. This may include adjustment, replacement of wear items, lubrication and cleaning, but not

modifications or repair of damage.

•MAY: This word is understood to be permissive.

•MUST: This word is understood to be mandatory.

•OPERATION: The correct and proper use of the machine as described in this manual.

•SAFETY ALERT SYMBOL: A symbol that indicates a potential personal safety hazard. It is composed of

an equilateral triangle surrounding an exclamation point.

•SHALL: This word is understood to be mandatory.

•SHOULD: This word is understood to be advisory.

•WARNING: Indicates a potentially hazardous situation, which if not avoided, may result in death or

serious personal injury.

SPECIFICATIONS ___________________________________________________________

Max. Spring Compression Capacity ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3000 lbs (1361 kgs)

Min./Max. Spring Diameters ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3.5 / 11.5 in (9 / 29 cm)

Packaged Dimensional data ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 18.5 x 20 x 43.63 in (47 x 51 x 111 cm)

Shipping Weight ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 100 lbs (45 kgs)

INSTALLATION INSTRUCTIONS________________________________________________

1. Unpack and remove the unit from the shipping carton.

2. Inspect the unit for any visible damage.

3. Install on a solid vertical wall or post. (Can also be installed on an OPTIONAL benchmount or portable

cart)

4. Anchor the unit to the wall or post utilizing the two holes in the back plate. Make sure there is no

movement between the back plate and wall or post.

CAUTION

Before using this product, read and fully understand the operating

instructions and all decals on the product. This is necessary to

prevent injury to the operator and damage to the product.

Do not attempt to use this product for anything other than its

intended purpose.

Do not use this product if it is visibly worn, distorted or damaged.

Always check condition of rubber hook pads on all six hooks before

using this tool. Replace if damaged or missing.

Always wear appropriate eye protection.

Inspect the spring of the strut assembly for any damage or

corrosion. Spring breakage during compression could cause injury.

WARNING

Failure to properly position the strut assembly in tool could result in

serious injury from sudden release of the strut assembly parts.

OPERATING INSTRUCTIONS________________________________________________

Step 1. Positioning the Strut Assembly

A) Adjust lower right hook to a position just below the lower center hook. Adjust lower left hook to a position

just above the lower center hook.

B) Place strut assembly on the lower center hook using the lowest possible coil of the spring.

C) Engage lower left and right hooks with spring. Center the spring within lower hooks. The three lower

hooks should be equally extended.

CORRECT INCORRECT

D) Align strut assembly by adjusting the lower left and right hooks. When properly aligned, the spring of the

strut assembly will be parallel to the posts of the tool when viewed from both the front and side.

Front Front

CORRECT INCORRECT

Side Side

CORRECT INCORRECT

E) Identify the strut assembly type you are servicing.

Type 1 Type 2

This type of strut has a bearing plate (which This type of strut has a bearing plate (which

rotates) and upper spring seat. Place upper rotates) and upper spring seat without space

hooks on the upper spring seat. Do not between them. Place upper hooks on the

place hooks on bearing plate. highest coil of the spring. Do not place hooks

on bearing plate.

Type 3 Type 4

This type of strut has only an upper spring This is a coil over shock. Place upper hooks

seat. Place upper hooks on upper spring on the highest coil of the spring.

seat.

F) Engage all three upper hooks as shown above for the type of strut assembly you are servicing. The three

upper hooks should be equally extended and contacting the strut.

CORRECT INCORRECT

Step 2. Disassembly

A) With the strut assembly properly positioned, turn handles to compress spring until the bottom coil of spring

is just free of the lower spring seat. DO NOT OVER COMPRESS THE SPRING!

B) Secure strut to spring with the clamp to prevent strut from dropping out unexpectedly.

C) Mark upper strut parts to aid in reassembly.

D) Working from the right side when facing strut compressor, remove the piston rod nut.

E) Remove the clamp while holding strut. Carefully remove strut and related parts.

F) Service or replace strut as required. It is not necessary to release spring from tool when servicing strut

only.

NOTE: When replacing top spring seat or spring, make note of the position of the spring seat and spring before

releasing spring from tool. Replace new strut parts in tool in the same position as the old.

CAUTION

If the strut assembly is difficult to compress or the spring bows or

tilts, release tension and reposition the strut assembly.

Keep fingers and hands clear of the upper hook area at all times.

WARNING

Use extreme care when working with a compressed spring.

Never remove the piston rod nut when there is any spring pressure

on the lower spring seat.

Step 3. Reassembly

A) Position the new strut within spring. Secure strut to spring with the clamp.

B) Install piston rod nut. NUT MUST BE FULLY ENGAGED ON PISTON ROD THREADS!

C) Release pressure on spring. Remove the clamp. Remove strut assembly from tool.

MAINTENANCE_____________________________________________________________

NOTE: To avoid personal injury or damage to the Model 7600, permit only qualified personnel to perform

maintenance.

See repair parts breakdown for replacement parts.

ALWAYS: Keep hooks and pads free of oil and grease.

DAILY: Inspect thrust bearing, drive screw, hooks, posts, lock pins and slots for

wear.

MONTHLY: Wipe down and clean ACME drive screw.

PERIODICALLY: Inspect unit for loose or missing components.

YEARLY: Clean and lightly lubricate thrust bearing.

___________________________________________________________________________

OWNER’S RECORDS Date Installed: _______________________

Date Code _______________________ Located under bottom plate

___________________________________________________________________________

REPAIR PARTS_____________________________________________________________

Inhaltsverzeichnis

Andere Branick Kompressor Handbücher

Branick

Branick 7400 Gebrauchs- und Pflegehandbuch

Beliebte Kompressor Handbücher anderer Marken

Panasonic

Panasonic Matsushita QA91K22CAU6 Bedienungsanleitung

EKOM

EKOM DK50 B Bedienungsanleitung

Challenge Xtreme

Challenge Xtreme CX 1500/1 Bedienungsanleitung

Conrad

Conrad 1719346 Bedienungsanleitung

Hanbell

Hanbell RC2-AV Series Bedienungsanleitung

PLASMATECH

PLASMATECH SHARK 25 Bedienungsanleitung

Emerson

Emerson Copeland Scroll Digital HLR Series Bedienungsanleitung

Drawmer

Drawmer 1968 MKII Bedienungsanleitung

Badger Air-Brush

Badger Air-Brush X-Air 80-8 Bedienungsanleitung

Omnitronic

Omnitronic CL-166 Bedienungsanleitung

Scheppach

Scheppach HC24V Montageanleitung

Ingersoll-Rand

Ingersoll-Rand centac C950 Technisches Handbuch

LG GVH282PAB Bedienungsanleitung

Kooper

Kooper 2196438 Bedienungsanleitung

American Eagle

American Eagle SHD-66DD Bedienungsanleitung

Frick

Frick 1510 Bedienungsanleitung

Sierra

Sierra Eagle 12 VX Handbuch

EUFAB

EUFAB 21083 Bedienungsanleitung