Braun ThermoScan IRT 4520 Bedienungsanleitung

IRT 4520

IRT 4020

Type 6022

Type 6023

IRT

4520/4020

KURTZ

DESIGN

ThermoScan

1-800-327-7226

Type: 6022

I / O

mem

6022351_IRT_CE_S1 Seite 1 Mittwoch, 10. Oktober 2007 2:52 14

IRT 4520

IRT 4020

1-800-327-7226

Type: 6022

ThermoScan

I / O

mem

1-800-327-7226

Type: 6022

start

ThermoScan

start

6022353_IRT_AP_S3 Seite 1 Donnerstag, 20. Dezember 2007 2:50 14

The Braun ThermoScan thermometer has been carefully developed

for accurate, safe and fast temperature measurements in the ear.

The shape of the thermometer prevents it from being inserted too far

into the ear canal to hurt the eardrum.

However, as with any thermometer, proper technique is critical to

obtaining accurate temperatures. Therefore, read the use

instructions carefully and thoroughly.

Important

• The operating ambient temperature range for this thermometer

is 10–40 °C (50–104 °F).

• Do not expose the thermometer to temperature extremes

(below –20 °C / –4 °F or over 50 °C / 122 °F) nor excessive humidity

(> 95 % RH).

• This thermometer must only be used with genuine Braun

ThermoScan Lens Filters (LF 40). Never use this thermometer

without a new, clean lens filter attached.

• Keep lens filters out of reach of children.

• This thermometer is intended for household use only.

• Use of this thermometer is not intended as a substitute for con-

sultation with your physician.

How does Braun ThermoScan work?

Braun ThermoScan measures the infrared heat generated by the

eardrum and surrounding tissues. To avoid gross temperature dif-

ferences, the sensor itself is brought to a temperature close to that of

the human body. When the Braun ThermoScan is placed in the ear,

it continuously monitors the infrared radiation. The measurement will

be finished and the result is displayed, when an accurate reading can

be assured.

Why measure in the ear?

The goal of thermometry is to measure core body temperature which

is the temperature of the vital organs. Ear temperatures accurately

reflect core body temperature, since the eardrum shares blood supply

with the temperature control center in the brain, the hypothalamus.

Therefore, changes in body temperature are reflected sooner and more

accurately in the ear than at other sites.

• Axillary temperatures only measure skin temperature and therefore,

are not a reliable indicator of core body temperature.

• Oral temperatures are influenced by drinking, eating and breathing.

• Rectal temperatures lag behind changes in core body temperature

and there is a risk of cross-contamination.

English

6022353_IRT_AP_N Seite 4 Donnerstag, 20. Dezember 2007 2:34 14

Body temperature

Normal body temperature is a range. The following table shows

that this normal range also varies by site. Therefore, readings from

different sites should not be directly compared.

• As well, a person’s normal temperature range tends to decrease

with age. The following table shows normal ThermoScan ranges

by age.

However, the range of normal also varies from person to person

and fluctuates throughout the day. It is therefore important to deter-

mine your normal temperature range. This is easily done using Braun

ThermoScan. Practice taking temperatures on yourself and healthy

family members to determine their normal temperature ranges.

Note: When consulting your physician, communicate that the

ThermoScan temperature is a temperature measured in the ear and

if possible, note the individual’s normal ThermoScan temperature

range as additional reference.

Normal ranges by site:

Axillary: 34.7 – 37.3 °C 94.5 – 99.1 °F

Oral: 35.5 – 37.5 °C 95.9 – 99.5 °F

Rectal: 36.6 – 38.0 °C 97.9 – 100.4 °F

ThermoScan: 35.8 – 38.0 °C 96.4 – 100.4 °F

Normal ThermoScan ranges by age:

0 – 2 years 36.4 – 38.0 °C 97.5 – 100.4 °F

3 – 10 years 36.1 – 37.8 °C 97.0 – 100.0 °F

11 – 65 years 35.9 – 37.6 °C 96.6 – 99.7 °F

> 65 years 35.8 – 37.5 °C 96.4 – 99.5 °F

6022353_IRT_AP_N Seite 5 Donnerstag, 20. Dezember 2007 2:34 14

Product description

1. Lens filter

2. Probe

3. Lens filter detector

4. Lens filter ejector

5. Display

6. «I/O» button

(On/memory function – IRT 4520 only)

7. «ExacTemp» light

8. «start» button

9. Battery door

10. Protective cover (IRT 4520)

11. Cap (IRT 4020)

How to use your Braun ThermoScan?

1. To achieve accurate readings, make sure a new,

clean lens filter (1) is in place before each

measurement.

2. IRT 4020: Push the «start» button (8).

IRT 4520: Push the «I/O» button (6).

During an internal self-check, the display shows

all segments. Then the last temperature taken will

be displayed together with «MEM».

Wait for the ready signal beep and the ready

symbol in the display.

3. Fit the probe snuggly into the ear canal, then push

the «start» button (8).

start

IRT 4020

IRT 4520

ThermoScan

6022353_IRT_AP_N Seite 6 Donnerstag, 20. Dezember 2007 2:34 14

If the probe has been fitted securely into the ear

canal during the complete measuring process,

a long beep will signal the end of the measuring

process. You can be assured to have taken an

accurate temperature reading. The result is shown

on the display (5).

If you take the temperature of another person, the

«ExacTemp» light (7) will be of help. It flashes

during the measuring process as long as the

probe is securely positioned, and lights up con-

tinuously when an accurate reading has been

taken.

4. If the probe has not been constantly placed in a

stable position in the ear canal, a sequence of

short beeps will sound, the «ExacTemp» light will

go out and the display will show an error message

(«POS» = position error).

5. For the next measurement, eject the used lens

filter (push ejector (4)) and put on a new, clean lens

filter.

IRT 4020: Clear the display by pushing the

«start» button once.

IRT 4520: Clear the display by pushing the

«I/O» button once.

Wait for the ready signal. Fit the probe snuggly

into the ear canal, then push the «start» button.

The Braun ThermoScan ear thermometer turns off

automatically after 60 seconds of inactivity.

The IRT 4520 can also be turned off by pressing

the «I/O» button for at least three seconds.

The display will shortly flash «OFF» and after

releasing the button it will go blank.

Temperature taking hints

• The right ear reading may differ from the reading

taken at the left ear. Therefore, always take the

temperature in the same ear.

• The ear must be free from obstructions or excess

earwax build-up to take an accurate reading.

• External factors may influence ear temperatures,

including when an individual has:

– been lying on one ear or the other

– had their ears covered

– been exposed to very hot or very cold tempera-

tures, or

– been recently swimming or bathing.

6022353_IRT_AP_N Seite 7 Donnerstag, 20. Dezember 2007 2:34 14

In these cases, remove the individual from the

situation and wait 20 minutes prior to taking a

temperature.

• Use the untreated ear if prescription ear drops or

other ear medications have been placed in the ear

canal.

Memory mode

The last temperature taken is stored in its memory

and will be automatically displayed when it is turned

on again. The display will show «MEM».

IRT 4520:

This model stores the last 8 temperature readings.

To display the stored readings, the thermometer

must be turned on. Then press the «I/O» button for

at least 1 second. The display shows the memory

number (e. g. MEM 1), and when releasing the

«I/O» button, the stored temperature for that memory

number is displayed, together with «MEM».

If «I/O» button is pressed too long, the thermometer

will be switched off. Each further pressing of the

«I/O» button displays the remaining memory numbers

(up to MEM 8).

MEM 1 is the latest reading, MEM 8 would be the

oldest.

The memory mode is left automatically after

displaying the oldest reading, or after pressing the

«I/O» button for at least 1 second.

Changing the temperature scale

Your Braun ThermoScan is shipped with the Celsius

(°C) temperature scale activated. If you whish to

switch to Fahrenheit (°F) and/or back from Fahrenheit

to Celsius, proceed as follows:

(1) Make sure the thermometer is turned off.

(2) Press and hold down the «start» button (IRT 4020)

or the «I/O» button (IRT 4520). After about 3

seconds the display will show this sequence:

«°C» / «SET» / «°F» / «SET» ...

(3) Release the «start» button / «I/O» button when the

desired temperature scale is shown. There will be

a short beep to confirm the new setting, then the

thermometer is turned off automatically.

6022353_IRT_AP_N Seite 8 Donnerstag, 20. Dezember 2007 2:34 14

Care and cleaning

The probe tip is the most delicate part of the

thermometer.

It has to be clean and intact to ensure accurate

readings.

If the thermometer is ever accidentally used without

a lens filter, clean the probe tip as follows:

Very gently wipe the surface with a cotton swab or

soft cloth moistened with alcohol. After the alcohol

has completely dried out, you can put a new lens

filter on and measure.

If the probe tip is damaged, contact Kaz.

Use a soft, dry cloth to clean the thermometer display

and exterior.

Do not use abrasive cleaners. Never submerge this

thermometer in water or any other liquid.

Store thermometer and lens filters in a dry location

free from dust and contamination and away from

direct sunlight.

Additional lens filters (LF 40) are available at most

stores carrying Braun ThermoScan or at Kaz Service

Centers.

6022353_IRT_AP_N Seite 9 Donnerstag, 20. Dezember 2007 2:34 14

Trouble-shooting

Error message Situation Solution

No lens filter is attached. Attach new, clean lens filter.

The thermometer cannot identify

a secure position of the probe.

An accurate measurement was

not possible.

POS = position error

IRT 4020: Clear the display by

pushing the «start» button once.

IRT 4520: Clear the display by

pushing the «I/O» button once.

Take care that the positioning of

the probe is correct and remains

stable.

Ambient temperature is not within

the allowed operating range

(10 – 40 °C or 50 – 104 °F).

Allow the thermometer to remain

in a room for 30 minutes where

the temperature is between

10 and 40 °C or 50 and 104 °F.

Temperature taken is not within

typical human temperature range

(34 – 42.2 °C or 93.2–108 °F).

HI = too high

LO = too low

Make sure a new, clean lens filter

is attached and thermometer is

properly inserted. Then, take a

new temperature.

System error – self-check display

flashes continuously and will not

be followed by the ready beep

and the ready symbol.

If error persists,

If error still persists,

Wait 1 minute until the thermo-

meter turns off automatically, then

turn on again.

... reset the thermometer by re-

moving the batteries and putting

them back in.

… have the thermometer checked

at a Kaz Customer Service Center.

6022353_IRT_AP_N Seite 10 Donnerstag, 20. Dezember 2007 2:34 14

Trouble-shooting

Error message Situation Solution

Battery is low, but thermometer

will still operate correctly.

Insert new batteries.

Battery is too low to take correct

temperature readings.

Insert new batteries.

Do you have any further

questions?

Please contact an authorized

Service Centre

(See Package Insert).

Replacing the batteries

The thermometer is supplied with two 1.5 V type AA (LR 06). For best

performance, we recommend Duracell

alkaline batteries.

Insert new batteries when the battery symbol appears on the display.

Open the battery compartment. Remove the batteries and replace with

new batteries, making sure the poles are in the right direction.

Slide battery door back until it snaps in place.

To protect the environment, dispose of empty batteries at

your retail store or at appropriate collection sites according to

national or local regulations.

Calibration

The thermometer is initially calibrated at the time of manufacture.

If this thermometer is used according to the use instructions, periodic

re-adjustment is not required. If at any time you question the accuracy

of the temperature measurement, please contact an authorized Kaz

Service Center.

Manufacturing date is given by the LOT number located in the battery

compartment. The first number after LOT represents the last digit of the

year of manufacture.

The next three digits give the day of the year of manufacture.

An example: LOT 0116 xx xx – this product has been manufactured on

the 116th day of the year 2000.

ThermoScan

6022353_IRT_AP_N Seite 11 Donnerstag, 20. Dezember 2007 2:34 14

Andere Handbücher für ThermoScan IRT 4520

Inhaltsverzeichnis

Andere Braun Thermometer Handbücher

Braun

Braun BNT300 Bedienungsanleitung

Braun

Braun ThermoScan IRT 4520 Bedienungsanleitung

Braun

Braun ThermoScan IRT 4020 Bedienungsanleitung

Braun

Braun IRT 6520B Bedienungsanleitung

Braun

Braun IRT 6020 Bedienungsanleitung

Braun

Braun BFH 125 Bedienungsanleitung

Braun

Braun IRT 3020 Bedienungsanleitung

Braun

Braun ThermoScan 4 Bedienungsanleitung

Braun

Braun ThermoScan 7+ Bedienungsanleitung

Braun

Braun ThermoScan IRT 3020 CO Bedienungsanleitung

Braun

Braun No touch + forehead Bedienungsanleitung

Braun

Braun BNT 400 Bedienungsanleitung

Braun

Braun NTF3000CAV1 Bedienungsanleitung

Braun

Braun ThermoScan IRT 4520 Bedienungsanleitung

Braun

Braun ThermoScan IRT 4520 Bedienungsanleitung

Braun

Braun Sensian 4 Bedienungsanleitung

Braun

Braun ThermoScan 3 Bedienungsanleitung

Braun

Braun 6022 Bedienungsanleitung

Braun

Braun ThermoScan IRT 6020 Bedienungsanleitung

Braun

Braun TempleSwipe BST200 Bedienungsanleitung

Braun

Braun TempleSwipe BST200US Bedienungsanleitung

Braun

Braun WelchAllyn ThermoScan Pro 3000 Bedienungsanleitung

Braun

Braun ThermoScan IRT 4520 Bedienungsanleitung

Braun

Braun ThermoScan 3 Bedienungsanleitung

Beliebte Thermometer Handbücher anderer Marken

Delton

Delton 981A Bedienungsanleitung

Baker

Baker MM2P Bedienungsanleitung

Tarmo

Tarmo 320281 Bedienungsanleitung

Citizen

Citizen CTD 504 Bedienungsanleitung

TFA

TFA 14.1500 Bedienungsanleitung

Vive

Vive DMD1010 Bedienungsanleitung

Gotemp

Gotemp THB4002 Bedienungsanleitung

GREISINGER

GREISINGER G 1202 Bedienungsanleitung

Amprobe

Amprobe TMD-53W Bedienungsanleitung

Trotec

Trotec BP10 Bedienungsanleitung

Radiance instruments

Radiance instruments RT616 Series Bedienungsanleitung

Eurolec

Eurolec IR151 Bedienungsanleitung

Scaneo

Scaneo TS42B Bedienungsanleitung

Sper scientific

Sper scientific 800043 Bedienungsanleitung

Motorola

Motorola MBP69SN Konfigurationshandbuch

The MeatStick

The MeatStick The MeatStick Bedienungsanleitung

Hama

Hama TH35-A Bedienungsanleitung

Veridian Healthcare

Veridian Healthcare 09-349 Bedienungsanleitung