Brite View BVP-5100D LinkE Mini Bedienungsanleitung

Tablet of Content

1.Important Information.........................................................................................................3

1.1 Important Safety Notes..............................................................................................3

1.2 Federal Communications Commission Interference Statement.................................4

2.INTRODUCTION ....................................................................................................................6

2.1 Package contents ......................................................................................................6

2.2 Product Overview ......................................................................................................6

2.2.1 Button/LED Descriptions.........................................................................................7

3. HARDWARE INSTALLATION ....................................................................................................8

3.1 Application 1 – Provide Network Connection for Your PC..........................................8

3.2 Application 2 – Extend Wireless Access Point Coverage...........................................9

4. Encrypted PLC Network..................................................................................................10

4.1 Create a Private Encrypted PLC Network Group.....................................................10

4.2 Remove Device from an Existing Network Group.................................................... 11

4.3 Create Additional Private Network........................................................................... 11

4.4 Standby Mode.......................................................................................................... 11

5.Enhance PLC Performance.............................................................................................12

6. SPECIFICATIONS ................................................................................................................14

1. IMPORTANT INFORMATION

1.1 Important Safety Notes

This product is intended for connection to the AC power line. For installation instructions, refer to the

Installation section. The following precautions should be taken when using this product.

zPlease read all instructions before installing and operating this product.

zPlease keep all instructions for later reference.

zPlease follow all warnings and instructions marked on the product.

zFor safety reason, when device is being powered on, DO NOT be installed in any electric

socket which makes the surface with venting holes on the product to face downward (facing

the floor).

zUnplug the Powerline device from the wall outlet before cleaning. Use a dry cloth for cleaning.

DO NOT use liquid cleaners or aerosol cleaners.

zDO NOT operates this product near water.

zThis product should never be placed near or over a radiator, or heat register.

zThis product relies on the building’s electrical installation for short-circuit (over current) protection.

zDO NOT allow anything to rest on the product interconnect plug. DO NOT locates this product where

people may walk on the cords and wires.

zBecause this product sends data over the power line, it is recommended that you plug directly into a

power outlet. Do not plug the device into a UPS or power strip with surge protection. The product has

its own power filter for protection against surges.

zOnly a qualified technician should service this product. Opening or removing covers may result in

exposure to dangerous voltage points or other risks.

zUnplug the product from the wall outlet and refer the product to qualified service personnel for the

following conditions:

¾When the interconnect cords are damaged or frayed.

¾If liquid has been spilled into the product.

¾If the product has been exposed to rain or water.

¾If the product does not operate normally when the operating instructions are followed.

¾If the product exhibits a distinct change in performance.

1.2 Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user's

authority to operate the equipment.

Labeling Requirements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

RF Exposure Warning

This equipment must be installed and operated in accordance with provided instructions and the

antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm

from all persons and must not be co-located or operating in conjunction with any other antenna or

transmitter. End-users and installers must be provide with antenna installation instructions and transmitter

operating conditions for satisfying RF exposure compliance.

Canada, Industry Canada (IC) Notices

This Class B digital apparatus complies with Canadian ICES-003 and RSS-210.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired operation of the

device.

Radio Frequency (RF) Exposure Information

The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency

exposure limits. The Wireless Device should be used in such a manner such that the potential for human

contact during normal operation is minimized.

This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile

exposure conditions. (antennas are greater than 20cm from a person's body).

Canada, avis d'Industry Canada (IC)

Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210.

Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer

d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent

affecter son fonctionnement.

Informations concernant l'exposition aux fréquences radio (RF)

La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences

radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors

du fonctionnement normal.

Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans

des conditions d'exposition à des appareils mobiles (les antennes se situent à moins de 20 cm du corps

d'une personne).

2. INTRODUCTION

The Powerline Ethernet Adapters take advantage of your home’s existing electrical wiring to build high

speed network connection for surfing website, video streaming, online gaming or any bandwidth

applications. Simply plug them to AC outlet and instantly establish powerline network. It means there is no

IP configuration or additional wires required.

2.1 Package contents

2.2 Product Overview

Powerline Ethernet Bridge

Two PLC devices Two Ethernet Cables

2.2.1 Button/LED Descriptions

Button/LED Description

ON: Power on and ready.

Blinking:

1. Slow blinking (2.0sec ON / 3.0 sec OFF): Sleep mode.

2. Fast blinking (0.5 sec ON / 0.5 sec OFF): PLC group pairing.

OFF: Power off.

ON: Ethernet connection detected.

Blinking: Network traffic in transaction.

OFF: No Ethernet connection detected.

ON: PLC connection detected.

Blinking:

1. Fast :

100Mbps > Powerline data rate > 60Mbps.

2. Normal :

60Mbps > Powerline data rate > 10Mbps.

3. Slow :

10Mbps > Powerline data rate.

OFF: No PLC connection detected.

(Too far for communication or not paired with other devices).

GROUP

Button

Press 10 seconds:

Randomly generate a new network group name.

Press 2 to 3 seconds:

Start paring with the other PLC device. Paring procedure keeps for 2

minutes or ends automatically when they are paired. It can be stopped

manually by pressing the button for 2 to 3 seconds again.

RESET Button Press 1 to 2 seconds: Reset to default group name HomePlugAV.

Press the button while the device is powered. (not in standby mode)

3. HARDWARE INSTALLATION

3.1 Application 1 – Provide Network Connection for Your PC

Provide Internet connection for network compatible device such as PC, Blu-Ray player or cable box in any

room at home.

3.2 Application 2 – Extend Wireless Access Point Coverage

To extend wireless AP coverage in different room or floor, user can place the Wi-Fi router/repeater near

the mobile devices such as iPad, Tablet, Smartphone and Notebook. Then connect the Wi-Fi

router/repeater to Powerline device that is connected to powerline network for delivering Internet signal.

4. ENCRYPTED PLC NETWORK

4.1 Create a Private Encrypted PLC Network Group

The Powerline bridges are compliant HomePlug AV specification. Every ‘HomePlug AV’ compliant PLC

device that has the same default network name, “HomePlug AV”, is capable of communicating with other

“HomePlug AV” devices. This is so called the “Public Network”. Two or more powerline devices under

the same network can communicate with one another.

If you have a pair of powerline device, either one in the pair can be “device A” or “device B”. By pressing

the GROUP button more than 10 seconds; it will generate a random network group (different from

HomePlug AV). Users can take the following two steps to change the public network group to the private

network group to protect their data while transmitting over the powerline. Users also can create more than

one private network groups by pressing GROUP button directly without software installation required.

*NOTE: Put the devices side by side will be more convenient during the setting procedure. After network group is set,

the devices can be deployed anywhere at home.

Step I: Clear Group Attribute

Clear the original network group of device B by pressing its GROUP button more than 10 seconds until all

LED lights simultaneously turns off and on once. At this moment, its network group name has been

changed to a random name. It means that this device is (1) ready to be assigned another network

name or (2) to be used as a seed device so other PLC devices can join to a private network group.

Step II: Join to Other Network Group

1. Press GROUP button of deviceA for 2 to 3 seconds (make sure POWER LED starts blinking).

2. Press GROUP button of device B for 2 to 3 seconds (make sure POWER LED starts blinking).

The device B which has cleared its group attribute will join to the deviceAwhich has not. This step makes

device A and B are under the same encrypted network. Additional device C can be added into device A’s

logical network by taking same steps, thus all of the device A, B, and C in the same encrypted network

group. User can assign as many powerline devices into the logical network group as described in the

SPECIFICATION section.

Inhaltsverzeichnis

Andere Brite View Adapter Handbücher

Brite View

Brite View BV-210 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung