Brivo T1BVT4D Bedienungsanleitung

T1BVT4D

4 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove1 enclosure with TBV1 Altronix/Brivo backplane

- One (1) Tango1B - PoE Driven Power Supply with

Lithium Battery Backup

- One (1) ACMS8CB - Dual Input PTC Access Power Controller

T1BV34SD

4 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove1 enclosure with TBV1 Altronix/Brivo backplane

- One (1) AL600ULXB - Power Supply/Charger

- One (1) ACM4CB - PTC Access Power Controller

- One (1) VR6 - Voltage Regulator

T2BV78SD

8 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove2 enclosure with TBV2 Altronix/Brivo backplane

- One (1) AL1024ULXB2 - Power Supply/Charger

- One (1) ACMS8CB - Dual Input PTC Access Power Controller

- One (1) PDS8CB - Dual Input PTC Power Distribution Module

- One (1) VR6 - Voltage Regulator

T2BV778SD

8 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove2 enclosure with TBV2 Altronix/Brivo backplane

- Two (2) AL1024ULXB2 - Power Supply/Chargers

- One (1) ACMS8CB - Dual Input PTC Access Power Controller

- One (1) PDS8CB - Dual Input PTC Power Distribution Module

- Two (2) VR6 - Voltage Regulators

T3BV7716SD

16 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove3 enclosure with TBV3 Altronix/Brivo backplane

- Two (2) AL1024ULXB2 - Power Supply/Chargers

- Two (2) ACMS8CB - Dual Input PTC Access Power Controllers

- Two (2) PDS8CB - Dual Input PTC Power Distribution Modules

- Two (2) VR6 - Voltage Regulators

- One (1) RSB2 - Rocker Switch Bracket with

Two (2) Rocker Switches (Not evaluated by UL)

Rev. TBVKD_110221

Installing Company: _________________________ Service Rep. Name: __________________________________________

Address: _________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners.

Installation Guide

All components of these Trove kits are UL Listed sub-assemblies.

Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

Access & Power Integration

- 2 - Trove Brivo PTC ULXB Kits Installation Guide

Overview:

Altronix/Brivo Trove kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed Altronix power supply/chargers and

sub-assemblies. These kits also accommodate various combinations of Brivo boards for up to sixteen (16) doors in a single enclosure.

Configuration Chart:

Altronix

Model Number Input

Power

Supply

Board

Input

Fuse

Rating

Power

Supply

Board

Battery

Fuse

Rating

Maximum Supply

Current for Main and

Aux. Outputs on

Power Supply board and

ACM4/ACMS8 Access

Power Controllers’

outputs

Nominal

Output

Voltage

Range

(VDC)

Fail-Safe/

Fail-Secure

Dry Form

“C”

Outputs

Additional PTC

Protected Outputs

ACM4CB Board

Input Fuse Rating

ACM4CB Board

Output PTC Rating

ACMS8CB Board

Output PTC Rating

PD8S8CB Board

Input PTC Rating

PD8S8CB Board

Output PTC Rating

T1BVT4D PoE

up to 90W N/A 10A/

32V

12VDC @ 5A

24VDC @ 3A

20.17-

26.4 8 – – – 2.5A – –

T1BV34SD 115VAC 60Hz,

3.5A

5A/

250V N/A 24VDC @ 5.9A 20.17-

26.4 4 – 10A/

32V 2.5A – – –

T2BV78SD 115VAC 60Hz,

4.2A

5A/

250V

15A/

32V 24VDC @ 9.4A 20.17-

26.4 8 8 – – 2.5A 9A 2.5A

T2BV778SD 115VAC 60Hz,

8.8A

5A/

250V

15A/

32V

24VDC @ 9.4A

20.17-

26.4 8 8 – – 2.5A 9A 2.5A

T3BV7716SD 115VAC 60Hz,

8.8A

5A/

250V

15A/

32V

24VDC @ 9.4A

20.17-

26.4 16 16 – – 2.5A 9A 2.5A

9.7-

13.2

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.

Product is intended for indoor use only.

1. Remove backplane from enclosure. Do not discard hardware.

If your application requires a raised backplane, re-mount it using metal spacers and screws (provided).

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install two/three upper fasteners and screws

in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two/three upper screws; level and secure.

Mark the position of the lower two/three holes. Remove the enclosure. Drill the lower holes and install the fasteners. Place the

enclosure’s upper keyholes over the upper screws. Install the lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch(es) (Altronix Model TS112 or equivalent) in desired location, opposite hinge. Slide the

tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 2). Connect tamper switch wiring

to the Access Control Panel input or the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure.

4. Mount Brivo boards to backplane, refer to pages 3-7.

5. Refer to the Power Supply/Charger Installation Guide (Tango1B, AL600ULXB, AL1024ULXB2) and

corresponding Sub-Assembly Installation Guide (ACM4CB, ACMS8CB, PDS8CB, VR6) for

further installation instructions.

Fig. 1

Tamper Switch

(included)

To Access Control Panel or

UL Listed Reporting Device

Edge of

Enclosure

Trove Brivo PTC ULXB Kits Installation Guide - 3 -

ACS6000 Main Board

ACS6000 Accessory Board

Altronix Tango1B is mounted under ACMS8CB

Altronix ACMS8CB

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

Fig. 2 - T1BVT4D Conﬁgurations

T1BVT4D: Configuration of Brivo Controls Boards:

1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 2, 2a, pg. 3).

Note: Brivo board must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 2, pg. 3).

3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 2a, pg. 3).

4. Fasten backplane to Trove1 enclosure utilizing lock nuts (provided).

Pem

4/40 - 5/8”

Spacer

Brivo board Backplane

4/40 - 5/16”

Pan Head Screw

Fig. 2a

- 4 - Trove Brivo PTC ULXB Kits Installation Guide

ACS6000 Main Board

ACS6000 Accessory Board

Altronix

ACM4CB

TRG

TRIGGER

INPUT

ACM4

ACCESS POWER

CONTROLLER

LED1 LED2 LED3 LED4

MAIN

OUTPUT 1

NC C NO COM NC C NO COM NC C NO COM NC C NO COM

OUTPUT 2 OUTPUT 3

IN GND

OUTPUT 4

-- +

CONTROL

-- +

POWER

+INP- T +RET-

INTERFACE

NO C NC

FACP

Altronix VR6 is mounted under ACM4CB

Altronix

AL600ULXB

+ DC ---

BAT FAIL NC C NO NC C NO

+ BAT ---

AC FAIL

DCAC BAT

LG N

5A 250V

OPEN --- 24V

CLOSED --- 12V

To VR6 mounted under ACM4CB

12VDC

from VR6 output

Fig. 3 - T1BV34SD Conﬁgurations

T1BV34SD: Configuration of Brivo Controls Boards:

1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 3, 3a, pg. 4).

Note: Brivo board must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 3, pg. 4).

3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 3a, pg. 4).

4. Fasten backplane to Trove1 enclosure utilizing lock nuts (provided).

Pem

4/40 - 5/8”

Spacer

Brivo board Backplane

4/40 - 5/16”

Pan Head Screw

Fig. 3a

Trove Brivo PTC ULXB Kits Installation Guide - 5 -

ACS6000 Main Board

ACS6000 Accessory Board

Altronix VR6 is mounted under ACMS8CB

Altronix PDS8CB

Altronix ACMS8CB

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

+ INP1 --

OFF

IN1

IN2

Out1

<1 off 2>

+ INP2 --

IN2 Fuse

IN1 Fuse

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

Out2

<1 off 2>

Out3

<1 off 2>

Out4

<1 off 2>

Out5

<1 off 2>

Out6

<1 off 2>

Out7

<1 off 2>

Out8

<1 off 2>

PWR1 +

PWR2 +

COM (--- )

Altronix

AL1024ULXB2

+ DC ---

BAT FAIL NC C NO NC C NO

--- BAT +

AC FAIL

DCAC BAT

LGN

5A 250V

Fig. 4 - T2BV78SD Conﬁgurations

T2BV78SD: Configuration of Brivo Controls Boards:

1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 4, 4a, pg. 5).

Note: Brivo board must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 4, pg. 5).

3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 4a, pg. 5).

4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).

Pem

4/40 - 5/8”

Spacer

Brivo board Backplane

4/40 - 5/16”

Pan Head Screw

Fig. 4a

- 6 - Trove Brivo PTC ULXB Kits Installation Guide

ACS6000 Main Board

ACS6000 Accessory Board

Altronix VR6 is mounted under ACMS8CB

Altronix VR6 is mounted under PDS8CB

Altronix PDS8CB

+ INP1 --

OFF

IN1

IN2

Out1

<1 off 2>

+ INP2 --

IN2 Fuse

IN1 Fuse

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

Out2

<1 off 2>

Out3

<1 off 2>

Out4

<1 off 2>

Out5

<1 off 2>

Out6

<1 off 2>

Out7

<1 off 2>

Out8

<1 off 2>

PWR1 +

PWR2 +

COM (--- )

Altronix ACMS8CB

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

Altronix

AL1024ULXB2

+ DC ---

BAT FAIL NC C NO NC C NO

--- BAT +

AC FAIL

DCAC BAT

LGN

5A 250V

Altronix

AL1024ULXB2

+ DC ---

BAT FAIL NC C NO NC C NO

--- BAT +

AC FAIL

DCAC BAT

LGN

5A 250V

Fig. 5 - T2BV778SD Conﬁgurations

T2BV778SD: Configuration of Brivo Controls Boards:

1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 5, 5a, pg. 6).

Note: Brivo board must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 5, pg. 6).

3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 5a, pg. 6).

4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).

Pem

4/40 - 5/8”

Spacer

Brivo board Backplane

4/40 - 5/16”

Pan Head Screw

Fig. 5a

Trove Brivo PTC ULXB Kits Installation Guide - 7 -

ACS6000 Main Board

ACS6000 Accessory Board

Altronix VR6 is mounted under ACMS8CB

Altronix PDS8CB

Altronix VR6 is mounted under ACMS8CB

Altronix PDS8CB

Altronix ACMS8CB

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

Altronix ACMS8CB

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

+ INP1 --

OFF

IN1

IN2

Out1

<1 off 2>

+ INP2 --

IN2 Fuse

IN1 Fuse

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

Out2

<1 off 2>

Out3

<1 off 2>

Out4

<1 off 2>

Out5

<1 off 2>

Out6

<1 off 2>

Out7

<1 off 2>

Out8

<1 off 2>

PWR1 +

PWR2 +

COM (--- )

COM (---)

+ INP1 --

OFF

IN1

IN2

Out1

<1 off 2>

+ INP2 --

IN2 Fuse

IN1 Fuse

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

Out2

<1 off 2>

Out3

<1 off 2>

Out4

<1 off 2>

Out5

<1 off 2>

Out6

<1 off 2>

Out7

<1 off 2>

Out8

<1 off 2>

PWR1 +

PWR2 +

COM (--- )

Altronix

AL1024ULXB2

+ DC ---

BAT FAIL NC C NO NC C NO

--- BAT +

AC FAIL

DCAC BAT

LGN

5A 250V

Altronix

AL1024ULXB2

+ DC ---

BAT FAIL NC C NO NC C NO

--- BAT +

AC FAIL

DCAC BAT

LGN

5A 250V

Altronix

AL1024ULXB2

+ DC ---

BAT FAIL NC C NO NC C NO

--- BAT +

AC FAIL

DCAC BAT

LGN

5A 250V

RSB2

Fig. 6 - T3BV7716SD Conﬁgurations

T3BV7716SD: Configuration of Brivo Controls Boards:

1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 6, 6a, pg. 7).

Note: Brivo board must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 6, pg. 7).

3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 6a, pg. 7).

4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).

Pem

4/40 - 5/8”

Spacer

Brivo board Backplane

4/40 - 5/16”

Pan Head Screw

Fig. 6b

- 8 - Trove Brivo PTC ULXB Kits Installation Guide

T1BVT4D and T1BV34SD (Trove1) Enclosure Dimensions (H x W x D approximate):

18” x 14.5” x 4.625” (457mm x 368mm x 118mm)

4.5” (114.3mm) 4.5” (114.3mm) 2.75”

(69.9mm)

1.115” (28.3mm)

1.36” (34.5mm)

1.25” (31.8mm) 1.25” (31.8mm)

1.5” (38.1mm)

8.5” (215.9mm)6.5” (165.1mm)

1.5” (38.1mm)

8.5” (215.9mm)6.5” (165.1mm)

4.5” (114.3mm)

13.0” (330.2mm)

0.6” (15.2mm)

14.5” (321.3mm)

1.45” (36.8mm)

7.25” (184.2mm)

1.95” (49.5mm)

1.1” (27.9mm)

0.6” (15.2mm)

0.57” (14.5mm)

18.0” (457.2mm)

1.25” (31.8mm)

- 9 - Trove Brivo PTC ULXB Kits Installation Guide

T2BV78SD and T2BV778SD (Trove2) Enclosure Dimensions (H x W x D approximate):

27.25” x 21.5” x 6.5” (692.2mm x 552.5mm x 165.1mm)

6.75” (171.5mm)8.25” (209.5mm)

8.00” (203.2mm)

2.00” (50.8mm)

1.25” (31.8mm)

5.25” (133.4mm) 5.25” (133.4mm)7.00” (177.8mm)

1.25” (31.8mm)

6.25” (158.8mm) 19.80” (502.9mm)

1.00” (25.4mm)

27” (685.8mm)

1.5”

(38.1mm)

2.00” (50.8mm) 2.00” (50.8mm)

3.5”(88.9mm) 3.5”(88.9mm)

21.50” (546.1mm)

5.25” (133.35mm) 5.25” (133.35mm)

6.25” (158.8mm)

1.25”

(31.8mm)

0.85” (21.6mm)

0.5625” (14.3mm)

2.415” (61.3mm)

0.685” (17.4mm)

1.77”

(45mm)

0.885” (22.5mm)

1.125” (28.3mm)

Knockouts

2.00” (50.8mm) 2.00” (50.8mm)

- 10 - Trove Brivo PTC ULXB Kits Installation Guide

T3BV7716SD (Trove3) Enclosure Dimensions (H x W x D approximate):

36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm)

2”

(50.8mm)

8.75” (222.3mm) 8.75” (222.3mm)

8.62” (219mm)

7.06” (179.3mm)

1.25” (31.8mm)

2.00” (50.8mm) 7.12” (222.3mm) 9.5” (241.3mm) 9.5” (241.3mm)

30.12” (768.1mm)

14.01” (355.9mm) 14.01” (355.9mm)

1.25” (31.8mm) 1.55” (39.4mm)

1.78” (45.2mm)

1.25” (31.8mm)

1.07”

(27.2mm)

1.10” (27.9mm)

2” (50.8mm)

10.75” (273.1mm)10.75” (273.1mm) 10.62” (269.8mm)

2.00” (50.8mm)10.75” (273.1mm)10.75” (273.1mm) 10.62” (269.8mm)

36.12” (917.5mm)

33.63” (854.2mm)

3/4” Conduit

1” Conduit

1.75” Conduit

1.5” Conduit

1.75” Conduit

1.5” Conduit

3/4” Conduit

1” Conduit

3/4” Conduit

1” Conduit

3/4” Conduit

1” Conduit

3/4” Conduit

1” Conduit

2” Conduit

Andere Handbücher für T1BVT4D

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Brivo IP-Zugriffskontrollsysteme Handbücher

Brivo

Brivo ACS5000-E Bedienungsanleitung

Beliebte IP-Zugriffskontrollsysteme Handbücher anderer Marken

ZKTeco

ZKTeco SpeedFace-V5L Bedienungsanleitung

Jantar

Jantar REX A-1-9 Bedienungsanleitung

2N Access Unit Merkblatt

Kedacom

Kedacom KSCA120 Series Bedienungsanleitung

H3C

H3C WX2880X Bedienungsanleitung

G4S

G4S S870-EX Leitfaden

PRASTEL

PRASTEL M2000PE Bedienungsanleitung

Allegion

Allegion interflex IF-281 Cylinder Bedienungsanleitung

TECOM

TECOM TS1067E Bedienungsanleitung

Fermax

Fermax Memokey 100C Benutzerhandbuch

Fermax

Fermax CITYLINE MEMOKEY Bedienungsanleitung

Software House

Software House iSTAR Pro 2U RM Bedienungsanleitung

AKCP

AKCP SP+ Bedienungsanleitung

Bpt

Bpt HNA/102 Bedienungsanleitung

Civintec

Civintec CV9601T-T-1F Bedienungsanleitung

BioMax

BioMax N-X90W Bedienungsanleitung

ZKTeco

ZKTeco OP-200 Bedienungsanleitung

FingerTec

FingerTec s-Kadex Bedienungsanleitung