Broadcast Tools DTD-16 + G2 Bedienungsanleitung

Installation and Operation Manual

PROBLEM SOLVED

Due to the dynamic nature of product design, the information contained in this

document is subject to change without notice. Broadcast Tools, Inc., assumes no

responsibility for errors and/or omissions contained in this document. Revisions

of this information or new editions may be issued to incorporate such changes.

Broadcast Tools® is a registered trademark of Broadcast Tools,Inc.

All Sentinel® labeled products are registered trademarks of Broadcast Tools,Inc.

No part of this document may be reproduced or distributed without permission.

Visit www.broadcasttools.com for important product update information.

Manual update: 6/12/2023

Firmware Version: 2.02

If you need a firmware upgrade, contact Broadcast Tools®

No part of this document may be reproduced or distributed without permission.

ALL SPECIFICATIONS AND FEATURES FOR THIS PRODUCT ARE SUBJECT TO

CHANGE WITHOUT NOTICE

NOTE: We recommend the use of Chrome, Firefox or Safari as your browser.

DTD-16 + G2 NET

16 Channel DTMF Tone/Sequence Decoder with Ethernet

INC

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742

DTD-16+ G2 Net Installation and Operation Manual

Table of Contents

Section Title Page #

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Who to Contact for Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features/Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation/Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Surge Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

UPS Standby Power System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Program Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

USB/RS232 Serial/Ethernet Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Relay Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Open Collector Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Audio Input Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Programming Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Output Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Dip-switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Restoring Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Ethernet Setup and Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Ethernet “Quick Start” Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting via the Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Changing network settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Front and rear panel drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix

Connector and configuration jumper layout. . . . . . . . . . . . . . . . . . Appendix

WEBSITE:

Visit our web site for

product updates and

additional information.

CONTENTS

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 3

DTD-16+ G2 Net Installation and Operation Manual

INTRODUCTION

Thank you for your purchase of the DTD-16 + G2 NET DTMF Tone Decoder, which

we will refer to throughout the manual as the DTD-16 + G2 NET. We are confident

this product will give you many years of dependable service. This manual is intend-

ed to give you all the information needed to install and operate the Broadcast Tools®

DTD-16 + G2 NET.

SAFETY INFORMATION

Only qualified technical personnel should install the DTD-16 + G2 NET. Any

attempt to install this device by a person who is not technically qualified could result

in a hazardous condition to the installer or other personnel or damage to the DTD-

16 + G2 NET or other equipment. Please ensure that proper safety precautions have

been taken before installing this device. If you are unfamiliar with this type of equip-

ment, please contact a properly qualified engineer to handle the installation and

setup of the DTD-16 + G2 NET. Broadcast Tools, Inc., is unable to support NON-

Broadcast Tools software, hardware, or NON-Broadcast Tools

computer/hardware/software problems. If you experience these problems, please

research your hardware/software instruction manuals, or contact the manufacturers

technical support department.

WHO TO CONTACT FOR HELP

If you have any questions regarding your product or you need assistance, please con-

tact your distributor from whom you purchased this equipment. If you would like

more information about BROADCAST TOOLS® products, you may reach us at:

Broadcast Tools, Inc.

131 State Street

Sedro-Woolley, WA 98284-1503 USA

Voice: 360.854.9559

Fax: 866.783.1742

Internet Home Page: www.broadcasttools.com

E-mail:[email protected]

THANK YOU FOR CHOOSING

BROADCAST TOOLS® BRAND PRODUCTS!

CAUTION!

Broadcast Tools®

Products, as with any

electronic device, can

fail without warning.

Do not use this product

in applications where a

life threatening condition

could result due to failure.

NOTE:

This manual should be

read thoroughly before

installation and operation.

WEBSITE:

Visit our web site for

product updates and

additional information.

Broadcast Tools is a Veteran Owned Business

Designed, Assembled and Supported in WA State, USA

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 4

DTD-16+ G2 Net Installation and Operation Manual

OVERVIEW

Product Overview

The DTD-16 + G2 NET is a full-featured DTMF tone/sequence decoder that is user

programmable to decode single tones or sequences up to six tones in length which

can be assigned to any one of eight SPST normally open relays, eight open collec-

tors, USB serial, RS-232 serial, and Ethernet.

The DTD’s relay and open collector outputs can be programmed to close for the

duration of tone, pulse immediately after completion of detection, wait a pro-

grammed (up to 9.99 seconds) length of time after detection, or latch/unlatch.

Programming is performed using a non-dedicated PC via USB serial, RS-232 serial,

or Ethernet (TCP or UDP) using a terminal program like PuTTY or HyperTerminal.

Features/Benefits

• Decodes all 16 DTMF tones or user-programmed tone sequences.

• 8 SPST relay outputs and 8 open collector outputs triggered by tones or tone

sequences.

• Front panel tone audio input level control with a range of -20 to +24dbu

• Adjustable tone detection time.

• Front panel relay status, power, tone activity, program mode, and activity LEDs.

• Programmed via USB serial, RS-232 serial, Ethernet (TCP or UDP) connection.

• Mode configuration via front panel dipswitches.

• Relay, open collector, and tone audio connections on removable euro-block screw

terminal connectors to simplify wiring and service, mating plugs are supplied.

• Fully RFI proofed.

• Surge protected internal power supply, 9 VDC universal desktop power adapter

with IEC inlet included.

• Up to three units may be mounted on the optional RA-1 rack shelf, using four

supplied Velcro feet. Desktop and wall mounting are also possible.

Inspection

Please examine your DTD-16 + G2 NET carefully for any damage that may have

been sustained during shipping. If any damage is present, please notify the shipper

immediately and retain the packaging for inspection by the shipper. The package

should contain the DTD-16 + G2 NET, a 9 VDC power supply, a USB-A/B cable, a

“S9” RJ11-to-DB9 cable, a 7-foot BLUE straight-through CAT 5 cable, a 7-foot

GRAY crossover CAT 5 cable. Manuals can be downloaded from our web site.

WEBSITE:

Visit our web site for

product updates and

additional information.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 5

DTD-16+ G2 Net Installation and Operation Manual

INSTALLATION

Installation/Operation

Power

Connect the 2.1mm barrel type center positive power connector into the unit and the

9 VDC power supply with domestic connector into a 120 Vac 50-60 Hz power source.

Surge Protection

The DTD-16 + G2 NET has built-in resistance to voltage changes; we recommend

that you use a power surge protector or line conditioner on the incoming AC line.

Lightning strikes and/or other high voltage surges may damage your DTD-16 + G2

NET and connected equipment if it is not properly protected. For lightning protec-

tion devices, check out www.polyphaser.com and www.itwlinx.com.

UPS Standby Power System

We recommend that you connect your DTD-16 + G2 NET to a UPS standby power

system. A UPS, like the BE600M1 from APC helps to minimize the risk to the DTD-

16 + G2 NET and provides power during a power outage.

NOTE:

Never use any type of

power supply other

than the specified/sup-

plied power supply.

Check the power jack

on the back of the unit

to determine which

power supply is

required.

WEBSITE:

Visit our web site for

product updates and

additional information.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 6

DTD-16+ G2 Net Installation and Operation Manual

INSTALLATION

LED Indicators

“PWR”: Power LED (Green).

“DV” LED: Indicates valid DTMF tone detection (Yellow).

“PGM” LED: Flashes when in Programming Mode (Red).

“DAT” LED: Indicates serial data transfer (Red).

“K1”- “K8” Relay LEDs: Lit when the corresponding relay is on (Green).

Program (PGM) button

Used to toggle in and out of programming mode. See the “Programming” section of

this manual for more information.

“OPTIONS” Configuration Dip-switches

The DTD’s mode configuration is set via a four-position dipswitch, labelled”

OPTIONS” (S2), located on the front panel of the unit. See the “Dip-switch

Settings” section of this manual for more information.

Audio Input Gain Adjustment

The front panel “INPUT LVL” control may be used to adjust the DTMF tone detection

sensitivity from –20dBu to +24dBu. This control should be adjusted for solid DV tone

detection LED indication while normal DTMF tone audio being fed into the DTD.

DTMF Tone Detection Jumper Settings

JP1 = DTMF Tone detection jumper (Guard time)

The DTD is equipped with a 4-position jumper, labeled “JP1” on its PCB. This is

used to adjust how quickly DTMF tones are detected. The settings are as follows:

Fast = 50ms ON / 50ms OFF

Medium = 100ms ON / 100ms OFF. (Default)

Slow = 150ms ON / 150ms OFF.

USB PGM Port

This type B USB port is used to connect the DTD-16 + G2 NET to a computer for

configuration via a virtual COM port. See the “Programming” section of this manual

for more information.

RS-232 Serial PGM Port (RJ-11 Jack):

This RJ-11 jack is used to connect the DTD-16 + G2 NET to a computer’s COM port

for configuration via RS-232 serial using the included reverse modular cable with 9-

pin “S9” female D-sub adapter. See the “Programming” section of this manual for

more information.

LAN/NET Ethernet Port

This 10/100 Ethernet port is used to connect the DTD-16 + G2 NET to a computer

for configuration via telnet/TCP socket connections. See the “Ethernet” and

“Programming” sections of this manual for more information.

WEBSITE:

Visit our web site for

product updates and

additional information.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 7

DTD-16+ G2 Net Installation and Operation Manual

INSTALLATION

Relay Outputs

The eight relay outputs are SPST normally open/dry. Make your connections to the

desired relays K1 A/B through K8 A/B. Front panel LEDs indicate when a relay is active.

Open Collector Outputs

The open collector outputs are labeled OC9 through OC16. Make your connection

between the desired open collector and ground “GND”. The open collector (OCx) output

for the selected channel will go low to ground (GND) providing a return for a PIP/trigger

input, TTL/CMOS logic, or external relay. External pull-up resistors may be required in

some installations. NOTE: The open collectors are rated at up to 6 VDC @ 50 mA.

Audio Input Connection

Connect the audio feed supplying DTMF tone audio for your equipment to the “AUD-

“and “AUD+” removable screw terminals on the J04 top terminal block connector.

The cable shield should connect to the signal ground “GND”/ “SGND” terminal on the

bottom J04 terminal block connector. See above for pinouts. The input is Hi-Z, active

balanced and adjustable via the front panel “INPUT LVL” trim pot.

WEBSITE:

Visit our web site for

product updates and

additional information.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 8

DTD-16+ G2 Net Installation and Operation Manual

PROGRAMMING

WEBSITE:

Visit our web site for

product updates and

additional information.

Programming

The DTD can be programmed from a computer via its USB serial, RS-232 serial, or

Ethernet interface. See the “Ethernet” section of the manual for Ethernet setup

instructions.

Connecting via the USB Serial “PGM” port:

1. Connect the supplied USB A/B cable from the “USB PGM” jack on the DTD

rear panel to an available USB port on your PC. When you first plug the DTD

into your PC, it should automatically install the correct FTDI USB Serial “Virtual

COM port” drivers which will allow you to access the DTD on a COM port.

NOTE: If the DTD’s FTDI USB Serial “Virtual COM port” drivers do not auto-

matically install they may be downloaded here:

http://www.ftdichip.com/Drivers/VCP.htm

2. Start a serial terminal application like PuTTY, Tera Term or HyperTerminal con-

figured for the connected COM port set to 9600 baud, 8, N, 1, flow control to

NONE, Emulation set to ANSI, and local character echo enabled.

Connecting via the RS-232 Serial “PGM” port:

1. Connect the supplied “S9” RJ11 to DB9 adapter cable from the RJ11 PGM jack

on the DTD rear panel to an available RS232 serial COM port on your PC.

2. Start a serial terminal application like PuTTY, Tera Term or HyperTerminal con-

figured for the connected COM port set to 9600 baud, 8, N, 1, flow control to

NONE, Emulation set to ANSI, and local character echo enabled.

“S9” RJ11 to DB9 adapter pinout:

RJ-11

Adapter

DB-9 D-SUB

Pin #

4 3 RS-232 Receive

3 2 RS-232 Transmit

2 5 Ground

Product’s point of

view Function Name.

Modular connector’s

point of view.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 9

DTD-16+ G2 Net Installation and Operation Manual

PROGRAMMING

Programming Steps

1. Press the recessed front panel PGM button or type “p” in the terminal to enter

Program Mode. The red front panel PGM LED will blink to indicate the DTD is

in Program mode and the Program Menu will be displayed in the terminal window:

DTD-16+ VER 2.02

OUT-CMD ON/OFF CODES

01-0-0.00-1111/

02-0-0.00-2222/

03-0-0.00-3333/

04-0-0.00-4444/

05-0-0.00-5555/

06-0-0.00-6666/

07-0-0.00-7777/

08-0-0.00-8888/

09-0-0.00-9999/

10-1-0.10-101/

11-0-0.00-****/

12-0-0.00-####/

13-0-0.00-AAAA/

14-0-0.00-BBBB/

15-0-0.00-CCCC/

16-0-0.00-DDDD/

SELECT 01-16 & ENTER 0=MOM, 1=LATCH, 2=XLATCH

DELAY 000-999 (0.00-9.99 SEC), MOM OR ON CODE / OFF

CODE :

2. Type the output channel number, 01 through 16, a “- “(dash) will be displayed

after the number are entered along with a new line.

3. Type the single command digit to set the output mode: “0” for momentary, “1”

for Latch or “2” for Exclusive Latch. A “- “(dash) will be displayed after the

command digit and a new line will be displayed.

4. Enter a time delay value of 0.00 to 9.99 seconds as a three-digit value (000-999).

Do not enter the ".", it will be entered automatically. This is the time that will

elapse after a command is received and before the output is activated. The

default time delay before activation is 0.00 seconds. A “- “(dash) will be dis-

played after the command digit and a new line will be displayed.

5. Enter the DTMF tone or string value(s) you want to use to operate the selected

output. The default values are listed above.

To exit Program mode, press the ESC key. Program mode will be exited automati-

cally after 60 seconds of inactivity. When Program mode is exited the DTD will list

the current program values and perform a reset.

WEBSITE:

Visit our web site for

product updates and

additional information.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 10

DTD-16+ G2 Net Installation and Operation Manual

PROGRAMMING

Output Modes

Momentary

If you have selected the momentary function for this output channel, you can program

two codes up to 5 digits for the first code and 6 digits for the second code that can be

used to activate that output. If your code is shorter than 5 digits enter a “/” at the end of

the first data string. This will cause a new line to be displayed. Enter the second code

you want to momentarily trigger. If the string is less than 6 digits press the “Enter” key.

The codes for that output will now be saved and you can go on to programming another

output. The momentary output closure duration is 1 second.

Momentary Programming Example:

To program output 1 for momentary for code 123 and 321 with a time delay of 4.25 sec-

onds before activation:

425

123/ 321(CR)

Latch

For the Latch function, the first code will be used to latch the output on, and the second

code to turn latch it off. Program the “ON” code, from 1 to 6 digits. If it is shorter than

5 digits, terminate with the “/” character. A new line will be displayed. Now enter the

code you want to use to turn OFF that output. It must be from 1 to 6 digits long. If it is

shorter than 6 digits terminate with the “Enter” key. You cannot enter the same code to

latch an output on and turn it off.

Latch Programming Example:

To program output 2 for 456 latch on, 654 latch off with no time delay:

0.00

456/654(CR)

Exclusive Latch

For the Exclusive Latch function, the first tone/code will be used to latch the output on,

and the second tone/code to turn it OFF, if desired. You do not need to enter an OFF

code. In Exclusive latch mode, when any exclusive latch output is selected, all other

exclusive latch outputs will be reset. Enter the “ON” code, from 1 to 5 digits. If it is

shorter than 6 digits terminate with the “/” character. A new line will be displayed. Now

enter the code you want to use to turn off that output. It must be from 1 to 6 digits long.

If it is shorter than 5 digits terminate with the “Enter” key. You cannot enter the same

code to latch an output on and turn it OFF.

Exclusive Latch Programming Example:

To program output 2 for 789 x-latch on with time delay of .10 second:

010

789(CR)

WEBSITE:

Visit our web site for

product updates and

additional information.

Andere Handbücher für DTD-16 + G2

Inhaltsverzeichnis

Andere Broadcast Tools Medienkonverter Handbücher

Broadcast Tools

Broadcast Tools ADC-1 Bedienungsanleitung

Broadcast Tools

Broadcast Tools DAC-1 Bedienungsanleitung

Broadcast Tools

Broadcast Tools DTD-16 Bedienungsanleitung

Broadcast Tools

Broadcast Tools ADCS-III Bedienungsanleitung

Broadcast Tools

Broadcast Tools SR-4 G2 Bedienungsanleitung

Broadcast Tools

Broadcast Tools DTD-16 + G2 Bedienungsanleitung

Broadcast Tools

Broadcast Tools DTE-16 Plus Bedienungsanleitung

Broadcast Tools

Broadcast Tools DTD-16 Plus Bedienungsanleitung

Broadcast Tools

Broadcast Tools ADC-1 Plus Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung