Broadcast Tools GPI-16 Plus/RJ Bedienungsanleitung

ati

and

rati

anua

PROBLEM SOLVED

1989

2016

www

oad

asttools

Manual update: 04/12/2016 • Firmware version: 1.01 or greater

If you need a firmware upgrade, contact Broadcast Tools®

No part of this document may be reproduced or distributed without permission.

ALL SPECIFICATIONS AND FEATURES FOR THIS PRODUCT ARE SUBJECT TO

CHANGE WITHOUT NOTICE

NOTE: We recommend the use of Chrome, Firefox or Safari as your browser.

GPI-16 Plus/RJ

Sixteen Input RJ45 General Purpose Interface with

USB/RS-232 serial ports.

INC

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742

GPI-16 Plus/RJ Installation and Operation Manual

Table of Contents

Section Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page #

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Who to Contact for Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

RFI and surge suppression suggestions . . . . . . . . . . . . . . . . . . . . . . . . 4

RJ45 GPI Input connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

USB connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

RJ11 serial connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Serial terminal setup and start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Configuration commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PIP information retrieval commands . . . . . . . . . . . . . . . . . . . . . . . . . . 8

AT1616 information retrieval commands . . . . . . . . . . . . . . . . . . . . . . 9

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Fractional Schematics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix A

Connector, dip-switch and LED layout . . . . . . . . . . . . . . . Appendix B

Top cover label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix C

Connection Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix D

WEBSITE:

Visit our web site for

product updates and

additional information.

CONTENTS

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 3

GPI-16 Plus/RJ Installation and Operation Manual

INTRODUCTION

Thank you for your purchase of a Broadcast Tools® GPI-16 Plus/RJ, sixteen

input general purpose interface (referred to as the GPI-16 Plus/RJ throughout this

manual). We’re confident that this product will give you many years of dependable

service. This manual is intended to give you all the information needed to install and

operate the Broadcast Tools® GPI-16 Plus/RJ.

SAFETY INFORMATION

Only qualified personnel should install Broadcast Tools® products. Incorrect or

inappropriate use and/or installation could result in a hazardous condition.

WHO TO CONTACT FOR HELP

If you have any questions regarding your product or you need assistance, please con-

tact your distributor from whom you purchased this equipment. If you would like

more information about BROADCAST TOOLS® products, you may reach us at:

Broadcast Tools, Inc.

131 State Street

Sedro-Woolley, WA 98284-1503 USA

Voice: 360.854.9559

Fax: 866.783.1742

Internet Home Page: www.broadcasttools.com

E-mail:[email protected]

THANK YOU FOR CHOOSING

BROADCAST TOOLS® BRAND PRODUCTS!

CAUTION!

Broadcast Tools®

Products, as with any

electronic device, can

fail without warning.

Do not use this product

in applications where a

life threatening condition

could result due to failure.

NOTE:

This manual should be

read thoroughly before

installation and operation.

WEBSITE:

Visit our web site for

product updates and

additional information.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 4

GPI-16 Plus/RJ Installation and Operation Manual

OVERVIEW

Product Overview

The GPI-16 Plus/RJ interfaces 16 general purpose logic inputs via four RJ45 jacks

to a PC RS-232 serial COM or USB port. The user may select from two pre-pro-

grammed serial data formats; the “PIP” GPI format which is used on most of our

audio switchers, or the legacy AT-1616 format. The four RJ45 input jacks can con-

nect to the Broadcast Tools COA-37 XDS/RJ adapter using Cat5 cables for easy

interfacing with the DB-37 Relay port on a satellite receiver.

Features/Benefits

• Four user selectable unit ID's: 0 (default), 1,2, and 3.

• Four user selectable baud rates: 9600 (default), 4800, 19200, and 38400.

• PIP or AT1616 data format.

• USB and RS-232 interface for connection to PC.

• LED indicators for all 16 GPI inputs and power.

• GPI connections are on four RJ45 input jacks (four inputs per jack) to simplify

wiring and service. May be directly interfaced to the Broadcast Tools COA-37

XDS/RJ adapter.

• Fully RFI proofed.

• Surge protected internal power supply, 9 volt universal switching power adapter

with domestic connectors supplied.

• Up to four GPI-16 Plus/RJ’s may be rack mounted on one RA-1, 1-RU rack shelf.

Inspection

Please examine your GPI-16 Plus/RJ carefully for any damage that may have been

sustained during shipping. If any is noted, please notify the shipper immediately and

retain the packaging for inspection by the shipper. The package contains the GPI-

16 Plus/RJ, a USB type A/B cable, a modular cable with 9-pin “S9” female D-sub

adapter and a 9.0 VDC universal wall power supply with domestic AC power con-

nector. Manuals may be downloaded from our web site.

Installation

RFI and surge suppression suggestions

CAUTION! Installation of the GPI-16 Plus/RJ in high RF environments should be

performed with care. It is recommended that all cables connected to the GPI-16

Plus/RJ be looped through ferrite cores to suppress RF. Surge protection with RF

filtering is also suggested for the power supply. For lightning protection devices,

check out www.polyphaser.com and www.itwlinx.com.

WEBSITE:

Visit our web site for

product updates and

additional information.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 5

GPI-16 Plus/RJ Installation and Operation Manual

INSTALLATION

Installation

The GPI-16 Plus/RJ is designed be used with the Broadcast Tools COA-37 XDS/RJ con-

nector adapter to simplify the wiring between PC based broadcast automation systems and

the relay outputs found on broadcast satellite receivers. Interfacing with a satellite receiver

is a simple as connecting the COA-37 XDS/RJ to the receiver’s DB-37 Relay port and then

connecting the COA’s RJ45 relay output jacks to the GPI-16 Plus/RJ’s RJ45 GPI input jacks

using standard straight thru Cat5 Ethernet cables.

RJ45 GPI Input connections

The GPI-16 Plus/RJ’s sixteen general purpose inputs may be triggered by either pulling the

input to ground or releasing the input to a high state. A valid input must be 15ms or greater

in duration. External sources can be contact closures, open collectors or 5 to 24 volt logic

level sources. The impedance of each input is 22K ohms.

Input connections are via four RJ45 jacks labeled “RJ45 Inputs”: “1-4” “5-8” “9-12” “13-

16”. These input jacks can be connected to the Broadcast Tools COA-37 XDS/RJ adapter

using standard straight thru Cat5 Ethernet cables to facilitate quick installation of satellite

receivers with DB-37 relay ports that follow the XDS pinout.

Input jack 1-4 Pinout:

NOTE: Input jacks “5-8” “9-12” and “13-16” follow the same pin pattern, so pin 1 on the

“5-8” jack is GPI 5 and pin 7 is GPI 8, etc.

Power

2.1mm coaxial DC power jack, 9.0 - 12 VDC, center positive.

USB Port

This type B USB port is used to connect the GPI-16 Plus/RJ to a computer’s USB port using

the supplied USB A/B cable. When you first plug the GPI-16 Plus/RJ into your PC, it should

automatically install the correct FTDI USB Serial “Virtual COM port” driver which will

allow you to access the GPI-16 Plus/RJ on a COM port. If the GPI is being used for RS-232

serial operation the USVB connection will remain disconnected and driver installation is not

necessary.

NOTE: If the GPI-16 Plus/RJ’s FTDI USB Serial “Virtual COM port” drivers do not auto-

matically install they may be downloaded by clicking on the “setup executable” link found

here: http://www.ftdichip.com/Drivers/VCP.htm

WEBSITE:

Visit our web site for

product updates and

additional information.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 6

GPI-16 Plus/RJ Installation and Operation Manual

INSTALLATION

WEBSITE:

Visit our web site for

product updates and

additional information.

RS-232 Serial Port:

This RJ-11 jack is used to connect the GPI-16 Plus/RJ to a computer’s COM port for

RS-232 serial operation using the included reverse modular cable with 9-pin “S9”

female D-sub adapter. If the GPI is being used for USB operation this will remain

disconnected.

Configuration

The GPI-16 Plus/RJ can be connected to your computer by one of two interfaces;

USB, or RS-232 serial. Below are connection and configuration instructions for each

interface.

NOTE: Step by step “COM” port HyperTerminal setup instructions are available

on-line at www.broadcasttools.com under “Downloads”.

Configuration via the USB Port.

1. Connect the supplied USB A/B cable from the “USB” jack on the GPI-16

Plus/RJ to a USB port on your PC. When you first plug the GPI-16 Plus/RJ into

your PC, it should automatically install the correct FTDI USB Serial “Virtual

COM port” driver which will allow you to access the GPI-16 Plus/RJ on a COM

port. Once you've installed the driver, the GPI-16 Plus/RJ will be listed as “USB

Serial Port” in device manager.

NOTE: If the GPI-16 Plus/RJ’s FTDI USB Serial “Virtual COM port” drivers do not

automatically install they may be downloaded by clicking on the “setup executable”

link found here: http://www.ftdichip.com/Drivers/VCP.htm

2. Start a serial terminal application like Tera Term, PuTTY or HyperTerminal

configured for the USB COM port the GPI-16 Plus/RJ is assigned to at 9600

baud ,8,N, 1, flow control to NONE, Emulation set to ANSI, and local charac-

ter echo enabled.

3. Connect the supplied 9 VDC power supply connector in to the GPI-16 Plus/RJ’s

power jack labeled “9-12VDC”, then plug the power supply in to a power source

of 120vac 60Hz. Verify that the green “PWR/HB” LED is blinking. The unit

information will be displayed on the terminal window.

RJ-11

Adapter

DB-9 D-SUB

Pin #

4 3 RS-232 Receive

3 2 RS-232 Transmit

2 5 Ground

Product’s point of

view Function Name.

Modular Jack

Pin Numbers

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 7

GPI-16 Plus/RJ Installation and Operation Manual

INSTALLATION

Configuration via the RS-232 Serial Port.

1. Connect the supplied reverse modular cable with 9-pin “S9” female D-sub adapter

from the “RS-232” jack on the GPI to a RS-232 serial COM port on your PC.

2. Start a serial terminal application like Tera Term, PuTTY, or HyperTerminal

configured for the COM port the GPI-16 Plus/RJ is connected to at 9600 baud

,8,N,1 flow control to NONE, Emulation set to ANSI, and local character

echo enabled.

3. Connect the supplied 9 VDC power supply connector in to the GPI-16 Plus/RJ’s

power jack labeled “9-12VDC” and plug the power supply in to a power source

of 120vac 60Hz. Verify that the green “PWR/HB” LED is blinking. The unit

information will be displayed on the terminal window.

Configuration Commands

In most cases you will use the GPI-16 Plus/RJ’s default settings and not need to per-

form any additional configuration of the unit. If you need to check or change settings

on the GPI-16 Plus/RJ you can follow the steps below using a terminal application

like Tera Term, PuTTY, or HyperTerminal. To query the current configuration, use

the following command:

*ASU? - Where the unit would respond to its current configured Unit ID followed

by “SU” and then the three current configuration characters item values (xyz). No

carriage return or line feed is required. NOT case sensitive.

Command example: *ASU?

Response example: 0SU000

Unit ID 0, 9600 baud, PIP mode

To modify the unit’s configuration, use the following command:

*uSUxyz - Where “u” is the current unit ID, “x” is configuration item 1, “y” is con-

figuration item 2, and “z” is configuration item 3. No carriage return or line feed is

required. NOT case sensitive.

Command example: *0SU030 would set the unit ID to zero, baud rate to 38400 and

serial format to PIP.

Configuration Item 1 (unit ID = x): Enter the desired unit ID number:

0 = (NON-Polling). (default)

1 = Polling

2 = Polling

3 = Polling

Configuration Item 2 (baud rate = y): Enter the desired baud rate number:

0 = 9600 (default)

1 = 19200

2 = 4800

3 = 38400

WEBSITE:

Visit our web site for

product updates and

additional information.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 8

GPI-16 Plus/RJ Installation and Operation Manual

OPERATION

Configuration Item 3 (serial format mode = z): Enter the desired serial format number:

0 = PIP format (default)

1 = AT1616 format

NOTE: To reset the GPI-16 Plus/RJ to factory defaults. Pull input 16 low TWO to

THREE times within 5 seconds during repowering the unit. The PWR/HB will flash

rapidly indicating the defaults have been loaded.

Operation

Command Formats

The GPI-16 Plus/RJ may be configured to use either the PIP or AT1616 (input only)

serial format. The PIP serial format (default) is listed below and requires the use of

the unit ID to request input status (polling) or with a unit ID of zero (non-polling)

the GPI-16 Plus/RJ will send a serial status string each time an input changes state.

When the unit is restarted (power-up), unit information is issued in either mode.

PIP Information Retrieval Commands

PIP serial format: The (*) asterisk is the beginning of string, next is the unit ID (0-

3), then the command. No carriage return or line feed is required. Commands are

NOT case sensitive.

*uSPii - Request status for a single input 01 thru 16 where u is the unit ID and ii is

the status input number. No carriage return or line feed required. Commands are

NOT case sensitive.

Command Example: Request status of input 01: *0SP01

Response Example: S0P,01,x <cr><lf> where x is 0 if the corresponding input is

high,

1 otherwise.

*uSPA - Request status for ALL inputs, where u is the unit ID. No carriage return

or line feed required. Commands are NOT case sensitive.

Command Example: *0SPA

Response Examples:

S0P,A,x,x,x,x,x,x,x,x,x,x,x,x,x,x,x,x<cr><lf>

S0P,A,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0<cr><lf> When input 01 is pulled low.

S0P,A,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0<cr><lf> When input 01 is released back high.

Input 01 is the first character, while input 16 is the last character. x is 0 if the cor-

responding input is high, 1 otherwise.

*uU - Send Unit Information. No carriage return or line feed required. Commands

are NOT case sensitive. Response format: <product_name>_ver_<n.nn><cr><lf>

Command example: *0U

Response Example: GPI-16_Plus_ver_1.01<cr><lf>

WEBSITE:

Visit our web site for

product updates and

additional information.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 9

GPI-16 Plus/RJ Installation and Operation Manual

OPERATION

AT1616 Information Retrieval Commands

When configured for the AT1616 format mode the GPI-16 Plus/RJ sends a response

string in AT1616 format each time an input changes state. In AT1616 format mode

the unit ID is setting is ignored and the baud rate is fixed at 9600.

Each string consists of a dash (-) followed by 8 bytes. The first 4 bytes are ASCII

hex representations of 16 outputs which are not included in the GPI-16 Plus/RJ, but

are issued as all zeros.

The last four bytes represent the 16 inputs in ASCII hex format with four bytes:

16,15,14,13 12,11,10,9 8,7,6,5 4,3,2,1. If inputs 1,4,7,8,9,10,14,16 are all ON

(pulled to ground), then these four bytes would appear as: A3C9. In the above

example, the complete string would be -0000A3C9

Additional response examples:

Response string example for input 1 pulled low: -00000001

Response string example for input 1 returning high: -00000000

Response string example for input 2 pulled low: -00000002

Response string example for input 2 returning high: -00000000

Response string example for input 3 pulled low: -00000004

Response string example for input 3 returning high: -00000000

Response string example for input 4 pulled low: -00000008

Response string example for input 4 returning high: -00000000

Response string example for input 16 pulled low: -00008000

Response string example for input 16 returning high: -00000000

Response string example for inputs 1 thru 8 pulled low: -00000055

Response string example for input 1 thru 8 returning high: -00000000

Response string example for inputs 9 thru 16 pulled low: -00005500

Response string example for input 9 thru 16 returning high: -00000000

WEBSITE:

Visit our web site for

product updates and

additional information.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742 10

GPI-16 Plus/RJ Installation and Operation Manual

SPECIFICATION

Specifications:

GPI Inputs The sixteen general purpose inputs may be activated either

by pulling the input to ground or releasing the input to a high

state. A valid input must be greater than 15ms in duration.

External sources can be contact closures, open collectors

or 5 to 24 volt logic level sources. Input impedance is 22K

ohms (contact current per input 0.250 ma at 5 volts DC).

GPI Indicators Sixteen green LED’s indicating when an input is on or off.

When the LED is illuminated, the input is on/triggered.

Input Interfacing Four RJ45 GPI jacks. Refer to the factional schematic or

page 5 of this manual for wiring information.

USB Port: USB type B connector. FTDI USB-to-serial chipset, 4800,

9600, 19200, 38400 baud, 8 data bits, no parity, 1 stop bit.

Handshaking disabled.

RS-232 Serial Port RJ11 connector. 4800, 9600, 19200, 38400 baud, 8 data

bits, no parity, 1 stop bit. Handshaking disabled. A modular

cable with 9-pin “S9” female D-sub adapter is included.

Logic Flash microprocessor w/non-volatile memory

Power 9 VDC @ 600 ma / 120 Vac 50-60 Hz, domestic power sup-

ply supplied. Total product power requirement < 100ma.

Power Indicator Green LED, indicator will blink indicating proper operation.

Mechanical 6.10” x 3.75” x 1.60” (DWH)

Weight 2 pounds

Options Broadcast Tools: RA-1, 1-RU rack shelf. Up to four units

may be accommodated using adhesive Velcro pads.

Broadcast Tools: COA-37 XDS/RJ adapter.

WEBSITE:

Visit our web site for

product updates and

additional information.

Andere Handbücher für GPI-16 Plus/RJ

Inhaltsverzeichnis

Andere Broadcast Tools Aufnahmegeräte Handbücher

Broadcast Tools

Broadcast Tools TeleSwitch Six Bedienungsanleitung

Broadcast Tools

Broadcast Tools GPI-32 Bedienungsanleitung

Broadcast Tools

Broadcast Tools SRC-4 Bedienungsanleitung

Broadcast Tools

Broadcast Tools GPI 16 + G2 Bedienungsanleitung

Broadcast Tools

Broadcast Tools ProMix-1 Bedienungsanleitung

Broadcast Tools

Broadcast Tools GPI-24 Bedienungsanleitung

Broadcast Tools

Broadcast Tools Audio Sentinel Web Bedienungsanleitung

Broadcast Tools

Broadcast Tools GPI-16+ G2 NET Bedienungsanleitung

Broadcast Tools

Broadcast Tools TT-1 Plus Bedienungsanleitung

Broadcast Tools

Broadcast Tools STI-II Bedienungsanleitung

Broadcast Tools

Broadcast Tools GPIO-32+2 Bedienungsanleitung

Broadcast Tools

Broadcast Tools GPI-16 Plus/RJ Bedienungsanleitung

Broadcast Tools

Broadcast Tools Audio Sentinel Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch