Broadxent CW2200 Bedienungsanleitung

Wireless Broadband Router

User Manual

reproduced or transmitted in any form or by any means, electronic

or mechanical, for any purpose, without the express written

permission of the seller.

Disclaimer

Information in this document is subject to change without notice.

The material contained herein is supplied without representation or

warranty of any kind. The seller therefore assumes no

responsibility and shall have no liability of any kind arising from the

supply or use of this document or the material contained herein.

Trademarks

Microsoft and Windows are registered trademarks of Microsoft

Corporation. 54g is a registered trademark of Broadcom

corporation. All other trademarks mentioned in this document are

the property of their respective owners.

April 21, 2003 Rev01

F/W:2.02.14

DocNo: A205Rev02

Safety Instructions

For Installation

• Use only the type of power source indicated on the

marking labels.

• Use only the power adapter supplied with the product.

• Do not overload wall outlet or extension cords as this may

increase the risk of electric shock or file. If the power cord

is frayed, replace it with a new one.

• Proper ventilation is necessary to prevent the product

overheating. Do not block or cover the slots and openings

on the device, which are intended for ventilation and

proper operation. It is recommended to mount the product

with a stack.

• Do not place the product near any source of heat or

expose it to direct sunshine.

• Do not expose the product to moisture. Never spill any

liquid on the product.

• Do not attempt to connect with any computer accessory or

electronic product without instructions from qualified

service personnel. This may result in risk of electronic

shock or file.

• Do not place this product on an unstable stand or table.

For Using

• Power off and unplug this product from the wall outlet

when it is not in use or before cleaning. Pay attention to

the temperature of the power adapter. The temperature

might be high.

• After powering off the product, power on the product at

least 15 seconds later.

• Do not block the ventilating openings of this product.

• When the product is expected to be not in use for a period

of time, unplug the power cord of the product to prevent it

from the damage of storm or sudden increases in rating.

For Service

Do not attempt to disassemble or open covers of this unit yourself.

Nor should you attempt to service the product yourself, which may

void the user’s authority to operate it. Contact qualified service

personnel under the following conditions:

• If the power cord or plug is damaged or frayed.

• If liquid has been spilled into the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally when the

operating instructions are followed.

• If the product has been dropped or the cabinet has been

damaged.

• If the product exhibits a distinct change in performance.

iii

FCC Information

FCC Statement

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communication. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance of 20cm between the

radiator & your body.

Changes or modifications not expressly approved by the party responsibe for 

compliance could void the 

user's authority to operate the equipment.

Note: The antennas used for this transmitter must not be co-located or 

operating in conjuction with any other antenna or transmitter.

About This User Manual

For brevity, throughout this manual the “Wireless Broadband

Router” is referred to as “the router” or “the device” and following

terms or abbreviations are used interchangeably:

• Access Point-AP

• Wireless LAN-WLAN

• Ethernet network-LAN-network

This User Manual contains information on how to install and

configure your Wireless Broadband Router to get your network

started accessing the Internet. From now on, we will guide you

through the correct configuration steps to get your device up and

run.

Contents

1Introduction..................................................1

1.1 Overview........................................................................1

1.2 Features ........................................................................2

1.3 Package Contents.........................................................3

1.4 System Requirements ...................................................3

2Hardware Description & Installation.............5

2.1 Physical Outlook............................................................5

Front Panel..................................................................5

Rear Panel and Connectors........................................6

2.2 Hardware Connection....................................................7

Choosing a Place for the Router.................................7

Connecting the Wireless Broadband Router...............7

3Setting Up Ethernet / WLAN Client..............9

3.1 Overview........................................................................9

3.2 Setting up TCP/IP........................................................10

For Windows 98/ME..................................................10

For Windows 2000/XP...............................................12

3.2 Setting up Wireless Client............................................14

3.3 Checking Connection with the Router..........................15

4Web Configuration.....................................17

4.1 Accessing Web-Based Configuration Utility.................17

To enable Your Settings ............................................18

4.2 Viewing System Status................................................19

4.3 Configuration for NAT Routing Mode...........................20

WAN Configuration for NAT Routing Mode...............21

LAN Configuration for NAT Routing Mode.................26

Viewing Current DHCP Assignments........................27

Wireless Broadband Router User Manual

4.4 Configuration for Bridge Mode.....................................28

4.5 Wireless LAN (2.4G) Configuration..............................31

4.6 Filters...........................................................................36

Specifing Your IP Filter Rules....................................36

Filter Types................................................................37

Filter Scenario of the Wireles Broadband Router......38

Viewing Filter Log......................................................39

Other Firewall Settings..............................................39

4.7 Forwarding...................................................................41

Setting Up Forwarding Entries ..................................41

If you have a Web server on your network… ............42

4.8 Administration..............................................................44

5Troubleshooting.........................................47

6Specification ..............................................49

6.1 Hardware.....................................................................49

6.2 Software ......................................................................50

1 Introduction

1.1 Overview

Thank you for choosing this Wireless Broadband Router. This

Wireless Broadband Route is a multi-function device featuring a

wireless 54Mbps Access Point, a 4-port LAN switch and a WAN

port which extends your existing broadband Cable/ADSL

connection. It allows your Internet connection to be shared through

either the 54Mbps Access Point feature or the 10/100Base-TX

Ethernet switch, which also eliminates the purchase of additional

hub or switch. Now your wired and wireless network are integrated

to enjoy various bandwidth-consuming applications over the

Internet.

With the support of new emerged 802.11g draft standard, the

Access Point provides data transfer of up to 54 Mbps, up to 5 times

faster than 802.11b. Since 802.11g operates on the same

frequency of 2.4 GHz as 802.11b, it is backwards compatible with

existing Wi-Fi 802.11b devices. The benefit is that you can

preserve the existing 802.11b infrastructure while migrating to the

new screaming fast 802.11g.

The router can act as a DHCP server to automatically assign IP

addresses to your LAN devices. With the built-in Network Address

Translation (NAT) function, your LAN can access the Internet

through a single external IP address and at the same time is

protected against outside intruders. The router can also be

configured to filter internal access to the Internet. It is designed to

provide a reliable Internet access solution for the corporate

environment, the small office and the home user.

Wireless Broadband Router User Manual

1.2 Features

• One 10/100 Base-TX RJ-45 auto sensing and crossover

Ethernet WAN port for Broadband connection (Cable/DSL

or direct Ethernet)

• Four RJ-45 LAN ports for 10/100Base-TX auto sensing &

crossover Ethernet Switch LAN connection

• 802.11g Wireless LAN

• One external and one built-in antennas for wireless

technology

• PPPoE (PPP over Ethernet) Client with Keep

Alive/Connect On Demand Support

• PAP and CHAP Authentication

• DHCP Client

• MAC Address Cloning

• DHCP Server

• NAT

• Firewall Support

• Bridge Mode Support

• 802.1D Spanning Tree Bridging

• IP Filtering, IP Forwarding

• DMZ Hosting

• ASCII/HEX Format 64/128 Bit WEP Key for Wireless LAN

• Allow/Deny List for Wireless LAN

• VPN Support (IPSec Passthrough, and PPTP

Passthrough)

• Configurable through Web Browser via WAN/LAN

• Software Upgrade

• NTP/Manual System Clock

• Configuration Saving/Retrieving

• Event Log

Inhaltsverzeichnis

Andere Broadxent Netzwerk-Router Handbücher

Broadxent

Broadxent F5D7230-4 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise