Brother MFC-8460N Bedienungsanleitung

Before you can use the machine, you must set up the hardware and install the software.

Please read this “Quick Setup Guide” for the correct setup procedure and installation

instructions.

Keep this “Quick Setup Guide”, User’s Guide and supplied CD-ROM in a convenient place for

quick and easy reference at all times.

Step 1

Setting Up the machine

Step 2

Installing the Drivers & Software

Setup is Complete!

Installing the Drivers & Software

Setting Up

the machine

Windows®

USB

Windows®

Parallel

Windows

NT®4.0

Parallel

Macintosh®

USB

Macintosh®

Network

Windows®

Network

Administrators

MFC-8460N

MFC-8860DN

Quick Setup Guide

Warning Caution Improper Setup Note User’s Guide

Warnings tell you

what to do to prevent

possible personal

injury.

Cautions specify

procedures you

must follow or avoid

to prevent possible

damage to the

machine or other

objects.

Improper Setup

icons alert you to

devices and

operations that are

not compatible with

the machine.

Notes tell you how

you should respond

to a situation that

may arise or give

tips about how the

current operation

works with other

features.

Indicates reference

to the User’s Guide.

Carton components may differ from one country to another.

Save all packing materials and the carton.

Carton Components

Quick Setup Guide

CD-ROMs

For Windows®

For Macintosh®

User’s Guide

Drum Unit Assembly

(including Toner

Cartridge)

Telephone Line Cord

Adapter

(For Australia only)

AC Power Cord Telephone Line Cord

Austraria & New Zealand users: Hong Kong, Malaysia & Singapore users:

The mains plug supplied with this machine is a grounded three pin plug. Make sure that the AC socket will

accept this grounded three pin plug. This machine must be grounded, If in doubt, call a qualified electrician.

Philipine & Thailand users:

The mains plug supplied with this machine is a side grounded two pin plug. Make sure that

the AC socket will accept this side grounded two pin plug. This machine must be grounded,

If in doubt, call a qualified electrician.

■To ensure safe operation the supplied plug must be inserted only into a standard power outlet that is

properly grounded through the standard electrical wiring. None grounded equipment may cause an

electrical shock hazard, and may cause excessive electrical noise radiation.

■The interface cable is not a standard accessory. Please purchase the appropriate interface cable for

the interface you intend to use (Parallel, USB or Network).

■Do NOT connect the interface cable at this time. Connecting the interface cable is done during the

software installation process.

■USB interface cable

Please make sure you use a USB 2.0 interface cable that is no longer than 2.0 metres.

When you use a USB cable, make sure you connect it to the USB port of your computer and not to a

USB port on a keyboard or non-powered USB hub.

■Parallel interface cable

Please make sure you use a Parallel interface cable that is no longer than 2.0 metres.

Use a shielded interface cable that is IEEE 1284-compliant.

■Network cable

Use a straight-throgh Category 5 (or greater) twisted-pair cable for 10BASE-T or 100BASE-TX Fast

Ethernet Network.

1. Automatic Document Feeder (ADF)

2. Control Panel

3. Face-down Output Tray

Support Flap (Support Flap)

4. Front cover

5. Paper Tray

6. Power Switch

7. Document Cover

8. ADF Document Output Support Flap

■Getting Started

MFC-8460N

MFC-8860DN

Control Panel

1One Touch keys 2Status LED 3LCD (Liquid Crystal Display)

4Menu keys 5Dial Pad 6Stop/Exit key

7Start key 8Copy keys 9Mode keys

10 Fax and telephone keys 11 Print keys

For the details of the control panel, see “Control panel overview” in Chapter 1 of the User’s Guide.

When you move the machine, grasp the side handholds that are under the scanner. Do NOT carry the

machine by holding it at the bottom.

981011

12 345

981011

12 345

Table of Contents

Setting Up the machine

1. Install the Drum Unit Assembly .......................................................................4

2. Load Paper in the Paper Tray ..........................................................................5

3. Release the Scanner Lock ................................................................................ 6

4. Install the Power Cord and Phone Line .......................................................... 6

5. Set Your Country (For Australia / New Zealand Customer Only) ................. 7

6. Setting the Date and Time ................................................................................8

7. Setting your Station ID .....................................................................................9

8. Tone and Pulse dialling mode (not available for New Zealand) .................10

9. SelectingaReceiveMode..............................................................................10

10. Setting the LCD Contrast ...............................................................................11

Installing the Drivers & Software

Supplied CD-ROM “MFL-Pro Suite” ..............................................................................12

For USB Interface Cable Users

(For Windows®98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition) ....14

For Parallel Interface Cable Users

(For Windows®98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition) ....16

For Windows NT®Workstation Version 4.0 Users ......................................................19

For Network Interface Cable Users

(For Windows

98/98SE/Me/NT/2000 Professional/XP/XP Professional x64 Edition)

...21

For USB Interface Cable Users ......................................................................................24

■For Mac OS®9.1 to 9.2 ......................................................................................24

■For Mac OS®X 10.2.4 or greater .......................................................................26

For Network Interface Cable Users ...............................................................................29

■For Mac OS®9.1 to 9.2 ......................................................................................29

■For Mac OS®X 10.2.4 or greater .......................................................................31

■For Network Users and Administrators

BRAdmin Professional configuration utility (For Windows®users) ..........................34

BRAdmin Light configuration utility (For Mac OS®X users) ......................................36

■Options and Consumables

Options ............................................................................................................................37

Replacement Consumables ...........................................................................................37

Step 1

Step 2

Setting Up the machine

Do not connect the interface cable.

Connecting the interface cable is

done during the software

installation process.

1Open the front cover by pressing the front

cover (1) release button.

2Unpack the drum unit and toner cartridge

assembly.

3Gently rock it from side to side several times

to distribute the toner evenly inside the

assembly.

4Put the drum unit assembly into the

machine until it clicks into place.

5Close the front cover of the machine.

1Install the Drum Unit Assembly

(1)

Step 1

Setting Up

the machine

Windows®

USB

Windows®

Parallel

Windows

NT®4.0

Parallel

Macintosh®

USB

Macintosh®

Network

Windows®

Network

Administrators

1Pull the paper tray completely out of the

machine.

2While pressing the paper guide release

lever (1), slide the adjusters to fit the paper

size. Check that the guides are firmly in the

slots.

3Fan the stack of paper well to avoid paper

jams and misfeeds.

4Put paper in the paper tray.

Check that the paper is flat in the tray and

below the maximum paper mark (1).

5Put the paper tray firmly back into the

machine and unfold the output tray support

flap (1) before you use the machine.

2Load Paper in the Paper Tray

(1)

For details on supported paper

specifications, see “Acceptable paper and

other media” in Chapter 2 of the User’s

Guide.

(1)

1Push the lever (1) up to unlock the scanner.

(The gray scanner lock lever is located at

the back left side, under the document cover

(2).)

Do not connect the Parallel or USB

cable yet.

1Make sure that the power switch is off.

Connect the AC power cord to the machine.

2Plug the AC power cord into an AC outlet.

Turn the power switch on.

3Connect one end of the telephone line cord

to the socket on the machine marked LINE

and the other end to a modular wall socket.

3Release the Scanner

Lock

(2)

(1)

4Install the Power Cord

and Phone Line

If Scanner Locked appears on the LCD,

immediately release the scanner lock and

press Stop/Exit.

Step 1 Setting Up the machine

Setting Up

the machine

Windows®

USB

Windows®

Parallel

Windows

NT®4.0

Parallel

Macintosh®

USB

Macintosh®

Network

Windows®

Network

Administrators

Warning

■The machine must be fitted with an earthed plug.

■Since the machine is grounded through the power

outlet, you can protect yourself from potentially

hazardous electrical conditions on the telephone

network by keeping the power cord connected to

your machine when you connect it to a telephone

line. Similarly, you can protect yourself when you

want to move your machine by disconnecting the

telephone line first and then the power cord.

You must set your country so that the machine works

correctly on local telecommunication lines in each

country.

1Check that the power is turned on by

plugging in the power cord and turn the

power switch on.

2Press or to select the country

(AUSTRALIA or NEW Zealand).

Press OK when the LCD shows your

country.

3The LCD prompts you to make sure of the

country again.

4If the LCD shows the correct country, press

1to go to Step 5.

—OR—

Press 2to go back to Step 2to select the

country again.

5After the LCD shows Accepted for two

seconds, it shows Please Wait.

If you are sharing one phone line with an

external telephone, connect it as shown

below.

If you are sharing one phone line with an

external telephone answering device,

connect it as shown below.

Please set the receive mode to External

TAD.

For more details, see “Connecting an

external TAD” in Chapter 7 of the User’s

Guide.

Extension

Telephone

External

Telephone

(Example

for Australia)

TAD

(Example

for Australia)

Set Your Country

(For Australia / New Zealand

Customer Only)

Set Country

Australia

NEW Zealand

Select

& OK

Set Country

Australia

1.Yes

2.No

Enter Number

The machine displays the date and time, and prints it on every fax you send.

1Press Menu.

2Press 0.

3Press 2.

4Enter the last two digits of the year on the

dial pad, and then press OK.

(e.g. Enter 0, 6for 2006.)

5Enter the two digits for the month on the dial

pad, and then press OK.

(e.g. Enter 0, 3for March.)

6Enter the two digits for the day on the dial

pad, and then press OK.

(e.g. Enter 2, 5.)

7Enter the time in 24-hour format on the dial

pad, and then press OK.

(e.g. Enter 1, 5, 2, 5for 3:25 P.M.)

8Press Stop/Exit.

6Setting the Date and Time

02.Date/Time

Year:2006

Enter & OK Key

02.Date/Time

XX/XX/2006

Month:03

Enter & OK Key

02.Date/Time

XX/03/2006

Day:25

Enter & OK Key

02.Date/Time

25/03/2006

Time:15:25

Enter & OK Key

If you make a mistake, press Stop/Exit to

start from Step 1.

Step 1 Setting Up the machine

Andere Handbücher für MFC-8460N

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Brother Multifunktionsdrucker Handbücher

Brother

Brother MFC-J2320 Bedienungs- und Wartungshandbuch

Brother

Brother DCP 540CN - Color Inkjet - All-in-One Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Brother

Brother DCP-130C Bedienungsanleitung

Brother

Brother MFC-J4410DW Bedienungs- und Wartungshandbuch

Brother

Brother DCP-7040 Bedienungsanleitung

Brother

Brother DCP 585CW - Color Inkjet - All-in-One Benutzerhandbuch

Brother

Brother Work Smart MFC-J470dw Montageanleitung

Brother

Brother DCP 385C - Color Inkjet - All-in-One Bedienungsanleitung

Brother

Brother MFC-9320CW Bedienungsanleitung

Brother

Brother MFC-8440 Sicherheitsleitfaden

Brother

Brother MFC-8680DN Bedienungsanleitung

Brother

Brother MFC 5890CN - Color Inkjet - All-in-One Kurzanleitung

Brother

Brother HL-L2305W Bedienungsanleitung

Brother

Brother MFC-8680DN Montageanleitung

Brother

Brother Work Smart MFC-J650dw Bedienungs- und Wartungshandbuch

Brother

Brother MFC-J4310DW Bedienungsanleitung

Brother

Brother Work Smart MFC-J875dw Bedienungs- und Wartungshandbuch

Brother

Brother DCP-145C Bedienungsanleitung

Brother

Brother MFC-J4410DW Bedienungsanleitung

Brother

Brother DCP-J125 Bedienungsanleitung

Brother

Brother MFC J5910DW Bedienungsanleitung

Brother

Brother MFC-440CN Bedienungsanleitung

Brother

Brother P2500 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung

Copystar

Copystar CS 4551ci Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 4650EN Bedienungsanleitung