Brother QL-800 Betriebsanleitung

Product Safety Guide QL-800/QL-810W/QL-820NWB

Label Printer

Read the whole guide before using your product

and keep it for later reference.

AUS-ENG

QL-800/QL-810W/QL-820NWB

English

Introduction

Thank you for purchasing the QL-800/QL-810W/QL-820NWB (hereafter referred to as “the

QL Label Printer”).

The documentation included with the QL Label Printer including the Product Safety Guide (this

guide) and the Quick Setup Guide (printed) contains operating precautions.

For more information, and for information about software and using the printer on a network, see

the User’s Guide, which can be found on the Brother support website.

The latest version of your printer documentation is available from the Brother support website at

support.brother.com

Save all documentation for later reference.

Important Notice

Models may vary depending on the country.

The contents of this document are subject to change without notice.

The contents of this document may not be duplicated or reproduced, partially or in full, without

permission.

We assume no responsibility for damages arising from earthquakes, fire, other disasters,

actions of third parties, the user’s intentional or negligent operation, misuse, or operation under

other special conditions.

We assume no responsibility for damage (such as losses, loss of business profits, lost profits,

business disruptions, or a lost means of communication) that may result from the use or

inability to use the printer.

If the printer should be defective due to faulty manufacturing, we shall replace or repair it during

the warranty period.

We assume no responsibility for any damages that may result from incorrect operation of the

printer caused by connecting incompatible equipment or using incompatible software.

To use your printer safely

If your printer malfunctions, immediately stop using it, and then contact your Brother dealer.

Symbols used in this document

The following symbols are used throughout this document:

DANGER

Indicates an imminently hazardous situation which, if the product is

handled without following the warnings and instructions, will result in death

or serious injuries.

WARNING

Indicates a potentially hazardous situation which, if the product is handled

without following the warnings and instructions, could result in death or

serious injuries.

CAUTION Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injuries.

IMPORTANT Indicates information or directions that should be followed. Ignoring them

may result in damage or failed operations.

Indicates a risk of fire under certain circumstances

Indicates a risk of electrical shock under certain circumstances

Indicates a risk of burns under certain circumstances

Indicates an action that must not be performed

Indicates a risk of combustion if fire is nearby

Indicates a risk of injury if the indicated part of your printer is touched

Indicates a risk of injury, such as an electrical shock, if the indicated part of your printer is

disassembled

Indicates a risk of electrical shock if the operation is performed with wet hands

Indicates a risk of electrical shock if your printer is exposed to water

Indicates an action that must be performed

Indicates that the AC Power Cord must be disconnected from the electrical socket

English

Important safety instructions

DANGER

Battery Unit (Rechargeable Li-ion Battery included) (Optional: QL-810W/820NWB only)

DO NOT leave a drained Battery Unit in your printer for a long period of time. This could shorten the

life of the Battery Unit.

DO NOT use or leave the Battery Unit near a fire, heaters, or other high temperature (above 80 °C)

locations.

If your printer can be used only for a short period of time, even though the rechargeable battery

is fully charged, the rechargeable battery may have reached the end of its service life. Replace

the rechargeable battery with a new one. When removing and replacing the rechargeable

battery, cover the terminals of the old rechargeable battery with tape to avoid creating a short in

the rechargeable battery.

Keep the Battery Unit out of the reach of children, particularly infants, otherwise injury may

occur.

WARNING

Battery Unit (Rechargeable Li-ion Battery included) (Optional: QL-810W/820NWB only)

If your printer is not fully charged after the specified amount of time has passed, stop charging it,

otherwise a fire, electrical shock, or damage may occur.

DO NOT charge the rechargeable battery with a printer or AC Adapter other than that specified.

A fire, electrical shock, or damage may occur.

When shipping your printer, make sure you remove the rechargeable battery from the printer before

packaging for shipment.

If your printer is shipped with the rechargeable battery installed, there is a risk of fire, explosion, and

damage.

DO NOT insert foreign objects into your Battery Unit or its connectors, otherwise a fire, electrical

shock, or damage may occur.

If foreign objects are dropped into your Battery Unit, immediately turn it off, disconnect the AC Adapter/

AC Power Cord from the electrical socket, and then contact Brother customer service or your local

Brother dealer. If you continue to operate your Battery Unit, a fire, electrical shock, or damage may

occur.

DO NOT operate, charge, or store your Battery Unit in the following locations, otherwise leaking,

fire, electrical shock, or damage may occur:

Near water, such as in a bathroom or near a water heater, or in an extremely humid location

In a location where it is exposed to rain or moisture

In an extremely dusty location

In an extremely hot location, such as near open flames, heaters, or in direct sunlight

In a closed car under a hot sun

In a location where condensation may form

DO NOT try to disassemble or alter your Battery Unit as it may result in an electrical short,

explosion, smoke, fire, electrical shock, injury to yourself or others, or damage to the product or

other property. For servicing, adjustments or repairs, contact Brother customer service or your local

Brother dealer. (The warranty does not cover repairs for damage resulting from disassembly or

alterations performed by the user.)

If your Battery Unit operates abnormally (for example, if it produces smoke, an unusual odour, or

noise), stop using it, otherwise a fire, electrical shock, or damage may occur. Immediately turn your

printer off, and then contact Brother customer service or your local Brother dealer for repairs.

DO NOT place the product near chemicals or in a place where chemical spillage could occur.

DO NOT allow organic solvents, such as benzene, thinner, polish remover, or deodorises, to come

into contact with the plastic cover or cables. These may cause the plastic cover to warp or dissolve,

resulting in an electrical shock or fire. They may also cause the product to malfunction or become

discoloured.

DO NOT allow children to play with the plastic bag that contained your Battery Unit. Dispose of the

bag or keep it away from babies and children. There is a risk of suffocation.

DO NOT dispose of your Battery Unit with household waste. There is a risk of environmental

damage, explosion, and fire.

DO NOT use combustible sprays when cleaning your Battery Unit, and DO NOT use combustible

sprays near your Battery Unit. There is a risk of fire and electrical shock.

Examples of combustible sprays:

Dust removing cleaners

Pesticides

Disinfectants and deodorises that contain alcohol

Organic solvents or liquids such as alcohol

DO NOT allow the charging contacts or the surrounding areas to become dirty, or to come into

contact with foreign objects. There is a risk of burns and damage.

DO NOT touch the terminal with wet hands, otherwise electrical shock, equipment damage, ignition

or smoking may occur.

When not attached to the printer for use, cover the terminal with tape, etc. to prevent intrusion of

foreign material such as dust. Also, do not use if the terminal is dusty, etc.

When shipping the printer, make sure you remove the Battery Unit from the printer before packaging

for shipment. If the printer is shipped with the Battery Unit installed, there is a risk of ignition, rupture,

fire or malfunction.

WARNING

English

AC Adapter/AC Power Cord (AC Adapter is only for QL-810W/820NWB)

DO NOT allow liquids or metal objects to come into contact with the power supply plug, AC Adapter,

or AC Power Cord. In addition, DO NOT use the power supply plug, AC Adapter, or AC Power Cord

in a location where it may get wet, otherwise a fire, smoke, heat or electrical shock may occur.

If the power supply plug becomes dirty (for example, if it becomes covered with dust) disconnect it

from the electrical socket, and then wipe it with a dry cloth. If you continue to use a dirty power

supply plug, a fire may occur.

When disconnecting the AC Adapter/AC Power Cord from the electrical socket, DO NOT pull on the

cord. Hold the plug and pull it out of the electrical socket.

DO NOT insert foreign objects into the terminals of the AC Adapter/AC Power Cord, otherwise

burns or electrical shock may occur.

Use the AC Adapter, AC Power Cord, or cable correctly and observe the following precautions,

otherwise a fire or electrical shock may occur:

DO NOT damage the AC Adapter, AC Power Cord, or cable.

DO NOT modify the AC Adapter, AC Power Cord, or cable.

DO NOT twist the AC Adapter, AC Power Cord, or cable.

DO NOT severely bend the AC Adapter, AC Power Cord, or cable.

DO NOT pull on the AC Adapter, AC Power Cord, or cable.

DO NOT place objects on the AC Adapter, AC Power Cord, or cable.

DO NOT subject the AC Adapter, AC Power Cord, or cable to heat.

DO NOT bind the AC Adapter, AC Power Cord, or cable.

DO NOT allow the AC Adapter, AC Power Cord, or cable to be squashed.

If the AC Adapter/AC Power Cord is damaged, contact Brother customer service or your local

Brother dealer.

Keep the AC Adapter/AC Power Cord out of the reach of children, particularly infants, otherwise

injury may occur.

DO NOT use the AC Adapter/AC Power Cord near flames or heaters. If the covering of the

AC Adapter/AC Power Cord melts, a fire or electrical shock may occur.

WARNING

Before performing maintenance on your printer, such as cleaning, disconnect the AC Adapter/

AC Power Cord from the electrical socket, otherwise an electrical shock may occur.

If your printer is not used for a long period of time, disconnect the AC Adapter/AC Power Cord from

your printer and the electrical socket for safety reasons.

DO NOT overload electrical sockets or plug multiple devices into the same electrical socket. There

is a risk of fire, electrical shock, and damage.

DO NOT use damaged plugs or bent electrical sockets. There is a risk of fire, electrical shock, and

damage.

CAUTION

Printer

Keep out of the reach of children, particularly infants, otherwise injury may occur.

Stop operating your printer if it leaks or becomes discoloured, deformed, or otherwise defective.

DO NOT hold your printer by the DK Roll Compartment Cover. There is a risk of injury if the cover

detaches and your printer falls.

When connecting cables and accessories, make sure you connect them correctly and in the correct

order. Connect only items that are designed specifically for this printer. There is a risk of fire or

injury. See the instructions when connecting.

DO NOT hold the printer with only one hand. The printer may slip out of your hand.

Battery Unit (Rechargeable Li-ion Battery included) (Optional: QL-810W/820NWB only)

When attaching the Battery Unit to the printer, make sure that the screws are securely tightened.

If the screws are loose, the printer may fall and cause injury.

AC Adapter/AC Power Cord (AC Adapter is only for QL-810W/820NWB)

Make sure the AC Adapter’s power cord/AC Power Cord is accessible so that it can be removed in

an emergency. DO NOT place objects on or near the AC Adapter’s power cord/AC Power Cord.

Cutter

DO NOT touch the blade of the cutter.

DO NOT open the top cover when the cutter is operating.

WARNING

English

IMPORTANT

DO NOT remove the labels affixed to the printer. These labels provide operational information and

indicate the printer's model number.

DO NOT store the printer in an area exposed to high temperatures, high humidity, direct sunlight, or

dust. These could cause discolouration or a malfunction.

General Precautions

Printer

If the Bluetooth function and wireless LAN function are both turned on, the communication speed may

decrease due to radio wave interference. If this occurs, turn off the function that you are not using

(Bluetooth function or wireless LAN function).

DO NOT cover or insert foreign objects into the Label Output Slot, AC connector, or USB Port.

When not used for an extended period, remove the DK Roll from the printer.

Always keep the DK Roll Compartment Cover closed when printing.

When using optional accessories, use them as described in their instruction manuals.

DO NOT touch the printer with wet hands.

DO NOT touch paper or labels with wet hands, otherwise a malfunction may occur.

DO NOT lift the printer by the DK Roll Compartment Cover. The cover could come off and the printer

could fall and become damaged.

Use only the interface cable (USB Cable) included with the printer.

Battery Unit (Rechargeable Li-ion Battery included) (QL-810W/820NWB only)

At the time of purchase, the Battery Unit is slightly charged so that the operation of your printer can

be verified; however, the Battery Unit should be fully charged with the AC Adapter or battery charger

before your printer is used.

If you notice anything unusual about the Battery Unit the first time it is used, for example overheating

or rust, DO NOT continue to use the Battery Unit. Contact Brother customer service.

If the printer will not be used for a long period of time, remove the Battery Unit and cover the terminal

with tape, etc., and then store it in a location where it is not exposed to static electricity, high humidity,

or high temperatures. To maintain the efficiency and life of the Battery Unit, charge it at least once every

six months.

At the time of purchase, the Battery Unit is slightly charged so that the operation of the printer can be

verified; however, the Battery Unit should be fully charged using the specified charger (in combination

with dedicated AC Adapter, car adapter or battery charger) before the printer is used.

If you notice anything unusual about the Battery Unit during use, charging or storage, for example

overheating or rust, DO NOT continue to use the Battery Unit. Contact Brother customer service.

Power Cord

You should put the printer near an easily accessible, standard electrical socket.

LAN Connection (For QL-820NWB Only)

Caution: Connect this product to a LAN connection that is not subject to overvoltages.

Compilation and Publication Notice

Under the supervision of Brother Industries, Ltd., this guide has been compiled and published

covering the latest product’s descriptions and specifications.

The contents of this guide and the specifications of this product are subject to change without

notice.

If new versions of the printer operating system become available, this guide may not reflect the

updated features.

Therefore, you may find that the operating system described in this guide may differ from new

operating systems.

Brother reserves the right to make changes without notice in the specifications and materials

contained herein and shall not be responsible for any damages (including consequential) caused

by reliance on the materials presented, including but not limited to typographical and other errors

relating to the publication.

Trademarks

Microsoft, Windows, Windows Vista and Windows Server are registered trademarks of

Microsoft Corporation in the United States and other countries.

Apple, Macintosh, Mac OS, Safari, iPad, iPhone and iPod touch are trademarks of Apple Inc.,

registered in the United States and other countries.

Google Play is a trademark of Google Inc.

Wi-Fi and Wi-Fi Alliance are registered trademarks of the Wi-Fi Alliance.

WPA, WPA2, Wi-Fi Protected Setup and Wi-Fi Protected Setup logo and are trademarks of the

Wi-Fi Alliance.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such

marks by Brother Industries, Ltd. under licence.

Blue SDK

Android is a trademark of Google Inc.

Adobe and Reader are either registered trademarks of Adobe Systems Incorporated in the United

States and/or other countries.

QR Code is a registered trademark of DENSO WAVE INCORPORATED in JAPAN and other

BarStar Pro Encode Library (DataMatrix, MaxiCode, PDF417, RSS, CODE93, POSTNET,

Epson ESC/P is a registered trademark of Seiko Epson Corporation.

Each owner whose software title is mentioned in this document has a Software Licence

Agreement specific to its proprietary programs.

Any trade names and product names of companies appearing on Brother products, related

documents and any other materials are all trademarks or registered trademarks of those

respective companies.

AirPrint is a trademark of Apple Inc.

English

Open Source Licensing Remarks (QL-810W/820NWB)

This product includes open-source software.

To see the open source licensing remarks, go to the manual download selection on your model’s

home page of the Brother support website at support.brother.com

Regulation for QL-800/QL-810W/QL-820NWB

For Australia Only:

Support - For technical support of your Brother Product other than what you can resolve

through the User's Guide, please visit our Web Site or Support Web Site (see below) to

find an answer to FAQs/Troubleshooting, locating Drivers & Software.

Alternatively, please contact the Product Support Centre for any customer

care/technical support enquiry.

To contact Brother International (Aust) Pty Ltd for support on a Brother product

please see the details listed below:

Product Support Centre: Australia

Brother International (Aust) Pty Ltd

Phone: 02 8875 6000

Fax: 02 9870 7223

Brother support website: support.brother.com

Web Site: www.brother.com.au

E-mail: To submit an e-mail enquiry, visit www.brother.com.au go to Service and

Support area and follow the prompts.

Our Technical Support Consultants are available 5 days a week by phone during the

hours of 8.30am to 5.00pm (EST/EDST) Monday to Friday.

CAUTION (810W/820NWB only)

RISK OF EXPLOSION IF BATTERY IS REPLACED WITH AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Andere Handbücher für QL-800

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Brother Etikettendrucker Handbücher

Brother

Brother P-touch PT-1100 Bedienungsanleitung

Brother

Brother P-touch PT-D400 P-touch PTD400AD Bedienungsanleitung

Brother

Brother PT7100 - P-Touch B/W Thermal Transfer... Bedienungsanleitung

Brother

Brother P-touch D210 Bedienungsanleitung

Brother

Brother P-TOUCH QL-560 Bedienungsanleitung

Brother

Brother P-touch 2350 Bedienungsanleitung

Brother

Brother PT-1830C - Labeling System With full-length TZ Laminated... Montageanleitung

Brother

Brother PT1090 - P-Touch - Labelmaker Bedienungsanleitung

Brother

Brother P-Touch LA3776001 Bedienungsanleitung

Brother

Brother P-Touch PT-P700 Bedienungsanleitung

Brother

Brother P300BT Bedienungsanleitung

Brother

Brother QL 650TD - P-Touch B/W Direct Thermal... Bedienungsanleitung

Brother

Brother P-touch PT-1500PC Bedienungsanleitung

Brother

Brother PT 1650 - P-Touch 1650 B/W Thermal Transfer... Bedienungsanleitung

Brother

Brother QL-1100c Bedienungsanleitung

Brother

Brother P-Touch PT-1250C Bedienungsanleitung

Brother

Brother P-touch 9500PC Handbuch

Brother

Brother PT-D460BT Bedienungsanleitung

Brother

Brother QL-1100 Bedienungsanleitung

Brother

Brother P-touch PT-9400 Bedienungsanleitung

Brother

Brother PT-P750W Bedienungsanleitung

Brother

Brother P-Touch 1010 Bedienungsanleitung

Brother

Brother P-Touch 3600 Bedienungsanleitung

Brother

Brother p-touch D800W Bedienungsanleitung

Beliebte Etikettendrucker Handbücher anderer Marken

newell

newell Dymo LabelManager 210D Bedienungsanleitung

U-Line

U-Line BROTHER H-8754 Bedienungsanleitung

Tharo Systems

Tharo Systems H-435+ Bedienungsanleitung

Godex

Godex RT700 SERIES Bedienungsanleitung

ID Technology

ID Technology 252 Bedienungsanleitung

Labelmate

Labelmate MC-11 Bedienungsanleitung

CAB

CAB XD4M/300 Bedienungsanleitung

Avery Dennison

Avery Dennison Pathfinder 6057 Service-Handbuch

TSC

TSC PEX1000 Series Bedienungsanleitung

Adkins

Adkins Label Master Bedienungsanleitung

Epson

Epson LabelWorks LW-400 Bedienungsanleitung

Primera

Primera 510212 Bedienungsanleitung

Brady

Brady BradyPrinter S3100 Bedienungsanleitung

DuraLabel

DuraLabel LabPRO Bedienungsanleitung

Novexx Solutions

Novexx Solutions XLP 604 Bedienungsanleitung

Epson

Epson LabelWorks LW-400 Bedienungsanleitung

Dymo

Dymo LabelManager 420P Bedienungsanleitung

Epson

Epson LW-PX400 Bedienungsanleitung