BRUEL & KJAER LAN-XI Bedienungsanleitung
L
A
N
-
X
I
S
E
T
U
P
G
U
I
D
E
2015 Copyright © Brüel & Kjær. All rights reserved
1
WHAT’S IN THIS GUIDE?
• Configuration – Single Module with Battery....................................................................................................................................................... 3
• Configuration – Single Module without Battery ................................................................................................................................................. 4
• Configuration – Multiple Modules in a Frame .................................................................................................................................................... 5
• Connection and Setup......................................................................................................................................................................................... 6
• LAN-XI Firmware Update .................................................................................................................................................................................... 8
• Connecting to a Front end with Front-end Setup ............................................................................................................................................. 10
• Installing a LAN-XI Notar License ...................................................................................................................................................................... 12
• Using LAN-XI Notar............................................................................................................................................................................................ 13
• Changing Module Front Panels......................................................................................................................................................................... 15
• Using Power over Ethernet (PoE)...................................................................................................................................................................... 16
2
3
CONFIGURATION – SINGLE MODULE WITH BATTERY
1) Remove the hex wrench (QX-1315*, 2 mm) from its holder on the
side of the module.
2) Attach Battery Module for LAN-XI Type 2831-A, to the right
(looking from the back) of the LAN-XI module using the hex
wrench and the four captive screws.
3) Connect Type 2831-A to the LAN-XI module using Single Module
Battery Adaptor ZH-0686†shown.
4) Connect a network cable (LAN Cable AO-1450*, 2 m Cat 6).
5) If you are going to use LAN-XI Notar™ BZ-7848-A or Sonoscout™
NVH Recorder BZ-5950, insert a mini-SD card, micro-SD card or
micro-SD card with adaptor
‡(using local storage).
Shown: 16 GB Micro-SD Card with Mini-SD Adaptor UL-1018**.
150424
1
2
4
5
3
*Included with LAN-XI Module Types 3050, 3052, 3053, 3056, 3057, 3160 and 3161
†Included with Battery Module for LAN-XI Type 2831-A
‡Older modules have a mini-SD slot, newer modules a micro-SD slot
**Included with LAN-XI Notar BZ-7848-A
4
CONFIGURATION – SINGLE MODULE WITHOUT BATTERY
1) Connect a network cable. Shown: LAN Cable AO-1450*, 2 m Cat 6.
2) If you will not be using power over ethernet (Cat 5 or better
required), connect a power cable – one of:
– Mains Adaptor ZG-0426*, 90 – 264 VAC
– Charger for Li-Ion Battery ZG-0469†, 90 – 264 VAC
– Car Utility Socket Cable AO-0546, 10 – 32 VDC
– External Battery Cable AO-0548, 10 – 32 VDC
3) If you are going to use LAN-XI Notar™ BZ-7848-A or Sonoscout™
NVH Recorder BZ-5950, insert a mini-SD card, micro-SD card or a
micro-SD card with an adaptor‡.
Shown: 16 GB Micro-SD Card with Mini-SD Adaptor UL-1018**.
1
2
150425
3
*Included with LAN-XI Module Types 3050, 3052, 3053, 3056, 3057, 3160 and 3161
†Included with Battery Module for LAN-XI Type 2831-A
‡Older modules have a mini-SD slot, newer modules a micro-SD slot
**Included with LAN-XI Notar BZ-7848-A
5
CONFIGURATION – MULTIPLE MODULES IN A FRAME
1) Insert up to 5/11 LAN-XI front-end modules in Type 3660-C/D:
– 6-ch. Input Module LAN-XI 51.2 kHz Type 3050-A-060
– 4-ch. Input Module LAN-XI 51.2 kHz Type 3050-A-040
– 3-ch. Input Module LAN-XI 102.4 kHz Type 3052-A-030
– 12-ch. Input Module LAN-XI 25.6 kHz Type 3053-B-120
– 4-ch. Input Module/HS Tacho + 8-ch. Aux. Module LAN-XI
51.2 kHz Type 3056-A-040
– 3-ch. Bridge Input Module LAN-XI 102.4 kHz Type 3057-B-030
– Generator, 4/2-ch. Input/Output Module LAN-XI 51.2 kHz
Type 3160-A-042
– Generator, 2/2-ch. Input/Output Module LAN-XI 51.2 kHz
Type 3160-A-022
– 1-ch. Input + 1-ch. Output Module LAN-XI 204.8 kHz
Type 3161-A-011
2) Insert up to two Battery Module for LAN-XI Type 2831-A in the
rightmost slots.
3) Connect a mains power cable.
4) Connect a network cable:
– Use the left LAN connector to connect to the host PC
– The right LAN connector supports IEEE 802.3af PoE and can
source power to a LAN device that can be powered by PoE
Left LAN Connector Right LAN Connector
6
CONNECTION AND SETUP
Connecting a LAN-XI Module to a Network
Using DHCP
LAN-XI modules are configured to use a DHCP server by default.
When the front end is a DHCP client, simply connect it to the network
and network settings will be supplied by the DHCP server.
If the module has been set to a static IP address via the module’s
home page, you must reset the module to be a DHCP client:
1) Press and release the Control button on the front of the module
to display the menu
2) Scroll down the menu by pressing the button once for each menu
item.
3) Press and hold the Control button for 5 seconds while the cursor
is on ‘LAN reset’ in the display menu.
Using a Static IP
To assign the module a static IP, first connect the module directly to
the computer or through a DHCP network as explained above. Open
the LAN-XI module’s web page, by typing the IP address from the
front of the module into your web browser, and follow these steps:
1) Click Network.
2) Select Static.
3) Enter an IP address, and, if necessary, a mask and gateway.
4) Click Save changes.
The module now has a static IP.
Alternatively, use the Front-End Setup program, which works also if the
current IP address is not with your existing address range.
7
Connecting a LAN-XI Module Directly to a PC
This method only works when both the module and the computer are
configured to be DHCP clients. To reconfigure the module to be a
DHCP client, follow the instructions in “Connecting a LAN-XI Module
to a Network” on page 6.
To connect a LAN-XI module directly to a PC:
1) Connect the PC and LAN-XI module with a standard LAN cable and
wait until an IP address is obtained. The message that the PC may
give about having limited or no connectivity is an indication that
the connection is working.
An IP address in the default range 169.254.*.*, will be assigned to
the module and shown on its display.
2) Open a browser on your PC and enter the IP address to open the
front end’s web page (will also work on smartphones, tablets,
etc.).
Alternatively both the PC and the LAN-XI module may have static
addresses in the same subnet.
Setup of LAN-XI Notar
If your LAN-XI Notar was ordered at the same time as the LAN-XI module, then the LAN-XI Notar firmware and license will have been
installed and tested at Brüel & Kjær. Go to “Using LAN-XI Notar” on page 13.
If your LAN-XI Notar was ordered separately, go to “Installing a LAN-XI Notar License” on page 12.
8
LAN-XI FIRMWARE UPDATE
Brüel & Kjær continually updates LAN-XI firmware. To download a
firmware update to your LAN-XI modules, follow the directions in
“Connecting to a Front end with Front-end Setup” on page 10 or:
1) Go to www.bksv.com and select Service, User Support, Downloads
or
Connect to the module’s home page by typing the IP address from
the front of the module into your web browser and click
Downloads.
2) Select LAN-XI under Step 1 and LAN-XI Software Updates under
Step 2.
3) Click on the latest firmware link to download the firmware to any
location on your PC.
Inhaltsverzeichnis
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
