Brymen BM115 Bedienungsanleitung
USER'S
MANUAL
BM115/BM116
Versatile Clamp-on
Multimeter Series
1
1) SAFETY
This manual contains information and warnings that must be followed for operating the
instrument safely and maintaining the instrument in a safe operating condition. If the
instrument is used in a manner not specified by the manufacturer, the protection
provided by the instrument may be impaired.
The meter meets the requirements for double insulation to IEC61 1 -2- 32(2 2),
EN61 1 -2- 32(2 2), UL61 1 B-2- 32(2 3):
Category III 6 Volts ac and dc.
PER EC61010 OVERVOLTAGE NSTALLAT ON CATEGORY
OVERVOLTAGE CATEGORY II
Equipment of OVERVOLTAGE CATEGORY II is energy-consuming equipment to be
supplied from the fixed installation.
Note – Examples include household, office, and laboratory appliances.
OVERVOLTAGE CATEGORY III
Equipment of OVERVOLTAGE CATEGORY III is equipment in fixed installations.
Note – Examples include switches in the fixed installation and some equipment for
industrial use with permanent connection to the fixed installation.
OVERVOLTAGE CATEGORY IV
Equipment of OVERVOLTAGE CATEGORY IV is for use at the origin of the
installation. Note – Examples include electricity meters and primary over-current
protection equipment.
TERMS N TH S MANUAL
WARNING identifies conditions and actions that could result in serious injury or even
death to the user.
CAUTION identifies conditions and actions that could cause damage or malfunction
in the instrument.
2
WARNING
To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture. The meter is intended only for indoor use.
To avoid electrical shock hazard, observe the proper safety precautions when working
with voltages above 6 VDC or 3 VAC rms. These voltage levels pose a potential
shock hazard to the user.
Keep your hands/fingers behind the hand/finger barriers (of the meter and the test
leads) that indicate the limits of safe access of the hand-held part during measurement.
Inspect test leads, connectors, and probes for damaged insulation or exposed metal
before using the instrument. If any defects are found, replace them immediately.
This Clamp-on meter is designed to apply around or remove from uninsulated
hazardous live conductors. But still, individual protective equipment must be used if
hazardous live parts in the installation where measurement is to be carried out could be
accessible.
CAUTION
Disconnect the test leads from the test points before changing meter functions.
NTERNAT ONAL ELECTR CAL SYMBOLS
!
!!
!
Caution ! Refer to the explanation in this Manual
Caution ! Risk of electric shock
Earth (Ground)
Double Insulation or Reinforced insulation
Fuse
AC--Alternating Current
DC--Direct Current
Application around and removal from hazardous live conductors is permitted
2) CENELEC Directives
The instruments conform to CENELEC Low-voltage directive 73/23/EEC and
Electromagnetic compatibility directive 89/336/EEC
3
3) PRODUCT DESCR PT ON
This user's manual uses only representative model(s) for illustrations. Please refer
specification details for function availability to each model.
1) Transformer Clamp Jaw for AC
current magnetic field pick up
2) Hand/Finger Barrier to indicate
the limits of safe access of the
meter during measurement
3) Push-buttons for special
functions & features
4) Input Jack for all functions
EXCEPT non-invasive ACA current
function
5) Common (Ground reference)
Input Jack for all functions EXCEPT
non-invasive ACA current function
6) Slide-switch Selector to turn the
power ON/OFF and Select a
function
7) 3-3/4 digits 4 counts LCD
display
8) Jaw trigger for opening the
transformer clamp jaw
9) Jaw center Indicators, at where
best ACA accuracy is specified
1 ) Jaw marking lines for ACA
position error indication
4
4) OPERAT ON
DC Voltage and AC Voltage functions
Inputs are made through the test lead terminals.
Note: DC 4 . mV range is designed with 1 MΩ high input impedance for least
current drain in measuring small signals, and can cope better with most commercially
available voltage output transducers/adapters. The non-zero display reading is normal
when the meter inputs are open circuit, which will not affect actual measurement
accuracy. The meter will show a close to zero reading when the inputs are shorted.
Open input is actually a floating condition, which is not a zero-volt-input condition.
Note: AC 4 . mV range selection is by RANGE button manually, and is specified from
AC 4 mV & up for BM115 and from AC 6 mV & up for True RMS model BM116.
5
CAUTION
Using Resistance, Continuity or Diode function in a live circuit will produce false results
and may damage the instrument. In many cases the suspected component must be
disconnected from the circuit to obtain an accurate measurement reading
Ω
ΩΩ
Ω Resistance, and Continuity functions
Inputs are made through the test leads terminals. Slide-switch on defaults at Ω. Press
SELECT button momentarily to select Continuity function which is convenient for
checking wiring connections and operation of switches. A continuous beep tone
indicates a complete wire.
6
Diode test function
Inputs are made through the test leads terminals. Slide-switch on defaults at Ω. Press
SELECT button momentarily 2 times to select Diode test function. Normal forward
voltage drop (forward biased) for a good silicon diode is between .4 V to .9 V. A
reading higher than that indicates a leaky diode (defective). A zero reading indicates a
shorted diode (defective). An OL indicates an open diode (defective). Reverse the test
leads connections (reverse biased) across the diode. The digital display shows OL if
the diode is good. Any other readings indicate the diode is resistive or shorted
(defective).
7
ACA Current clamp-on function
Inputs are made through the clamp jaws for non-invasive ACA current measurements.
CAUTION (Application and removal of the Clamp-on meter)
Press the jaw trigger and clamp the jaws around only one single conductor of a circuit
for load current measurement. Make sure the jaws are completely closed, or else it will
introduce measurement errors. Enclosing more than one conductor of a circuit will
result in differential current (like identifying leakage current) measurement. Locate the
conductor(s) at the Jaws center as much as possible to get the best measuring
accuracy. For removal, press the jaw trigger and remove the jaws from the
conductor(s).
Adjacent current-carrying devices such as transformers, motors and conductor wires
will affect measurement accuracy. Keep the jaws away from them as much as possible
to minimize influence.
8
HOLD
The hold feature freezes the display for later view. Press the HOLD button
momentarily to activate and to exit the hold feature.
Relative zero mode
Relative zero mode allows the user to offset the meter consecutive measurements
with the displaying reading as the reference value. The display will now show readings
relative to the stored reference value. That is, display = reading - stored value. Press
the button momentarily to activate and to exit relative zero mode.
Manual or Auto-ranging
Press the RANGE button momentarily to select manual-ranging mode, and the meter
will remain in the range it was in, the LCD annunciator turns off. Press the
button momentarily again to step through the ranges. Press and hold the button for 1
second or more to resume auto-ranging mode.
Auto Power Off (APO)
When the meter is on, the Auto Power Off (APO) feature will switch the meter to sleep
mode automatically after approximately 3 minutes of no slide-switch nor push button
operations to extend battery life. To wake up the meter from APO, press the buttons
momentarily or set the slide-switch to the OFF position and then slide back on again.
Always set the slide-switch to the OFF position manually when the meter is not in use.
9
5) MAINTENANCE
WARNING
To avoid electrical shock, disconnect the meter from any circuit, remove the test leads
from the input jacks and turn OFF the meter before opening the case. Do not operate
with open case.
Trouble Shooting
If the instrument fails to operate, check batteries and test leads etc., and replace as
necessary. Double check operating procedure as described in this user’s manual
If the instrument voltage-resistance input terminal has subjected to high voltage
transient (caused by lightning or switching surge to the system) by accident or
abnormal conditions of operation, the series fusible resistors will be blown off (become
high impedance) like fuses to protect the user and the instrument. Most measuring
functions through this terminal will then be open circuit. The series fusible resistors and
the spark gaps should then be replaced by qualified technician. Refer to the LIMITED
WARRANTY section for obtaining warranty or repairing service.
Cleaning and Storage
Periodically wipe the case with a damp cloth and mild detergent; do not use abrasives
or solvents. If the meter is not to be used for periods of longer than 6 days, remove
the batteries and store them separately
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Brymen Multimeter Handbücher
Brymen
Brymen BM857 Bedienungsanleitung
Brymen
Brymen BM061 Bedienungsanleitung
Brymen
Brymen BM859s Bedienungsanleitung
Brymen
Brymen BM110M Bedienungsanleitung
Brymen
Brymen BM810 Series Bedienungsanleitung
Brymen
Brymen BM195 Bedienungsanleitung
Brymen
Brymen BM230R Series Bedienungsanleitung
Brymen
Brymen BM878 Bedienungsanleitung
Brymen
Brymen BM170D Series Bedienungsanleitung
Brymen
Brymen EEVblog BM235 Bedienungsanleitung
Brymen
Brymen BM251s Bedienungsanleitung
Brymen
Brymen TBM195 Bedienungsanleitung
Brymen
Brymen BM867s Bedienungsanleitung
Brymen
Brymen BM885 Bedienungsanleitung
Brymen
Brymen TBM161 Bedienungsanleitung
Brymen
Brymen BM161s Bedienungsanleitung
Brymen
Brymen TBM811 Bedienungsanleitung
Brymen
Brymen TopTronic TBM315 Bedienungsanleitung
Brymen
Brymen BM837RS Bedienungsanleitung
Brymen
Brymen BM905s Bedienungsanleitung
Beliebte Multimeter Handbücher anderer Marken
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Bedienungsanleitung
PeakTech
PeakTech 4000 Gebrauchs- und Pflegehandbuch
YOKOGAWA
YOKOGAWA 90050B Bedienungsanleitung
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung
Fluke
Fluke 8846A Bedienungs- und Wartungshandbuch
Tempo Communications
Tempo Communications MM200 Bedienungsanleitung
