BT Redcare Essential Extra Bedienungsanleitung
Essential Extra
Installation Guide
Contents
2 Introduction
5 Mounting And Wiring
9 Programming
16 Configuration
48 Disposal
49 Glossary Of Terms
50 Support
Introduction
3
Product Description
Figure 1 – Essential Extra unit (not to scale)
Essential Extra is a wireless dual path alarm signalling unit for transmitting alarm signals from a customer’s alarm panel,
via the BT Redcare network, to an Alarm receiving Centre (ARC). Essential Extra units have dual modems with 4G/2G
mobile technology in each path. The units are designed for use in both Security and Fire systems.
The unit communicates via the BT Redcare Network and a valid TA account must exist for the unit to communicate.
The TA account will have been populated with the serial number of the unit.
The unit has 16 general purpose alarm inputs, and 3 outputs, making it suitable for connection to most common alarm
panels.
The unit is supplied already fitted with two BT Redcare enabled SIM cards, one an EE UK fixed SIM and a UK Roaming SIM.
Both enabled for 4G/2G connectivity.
4
Specifications
Size: 114mm x 67mm x 20mm
Power: 9V – 30V
Current:
Alarm inputs: 16 General purpose inputs 1-16. (-0.5V – 30V)
Alarm threshold: High >2V, and Low <1.3V
Outputs: 3 x Relay NO C NC (Comms, Func, Fire)
RS232 port: remote panel access (UDL) and signalling to some intruder panel types
RS485 port: remote panel access (UDL) and signalling to some intruder panel types
Configuration: Using on board configuration buttons, web portal or App
Processor: STM32
Wireless modules: ELS61
Average Average Max loading
Normal Operation (inc relays and dial capture operated)
4G/4G unit @12V 110mA 190mA
4G/4G unit @24V 50mA 110mA
Mounting and Wiring
6
Removal of Cover
The top cover can be removed by gently releasing each of the 4 clips on the base of the unit by pushing the clips outward
with a screwdriver blade.
Regular access to the inside of the unit should not be required, although occasional access may be required to access the
SIM cards.
Mounting
The unit should be mounted inside the alarm panel, or inside a separate powered housing, using the sticky mounting pads
supplied.
For security installations the enclosure must meet or exceed the protection requirements of the particular security grade
for the whole installation as per EN 50131-1.
For fire alarm panels the enclosure must meet the requirements of EN 54-21 7.3 (eg. IP30 or above). Enclosure
requirements for the signalling unit are the same as for the fire alarm panel itself and must meet EN 54-2. The enclosure
must restrict access to installer level 3. The enclosure must provide the facility to indicate the state of the fault and
acknowledge outputs on the signalling unit.
The supplied aerial should be mounted vertically outside of the housing by removing the adhesive backing.
Figure 2 - Layout of terminals (not to scale)
7
Connection Terminals
The screw terminals for the alarm inputs are suitable for use with a standard 3mm blade terminal screwdriver.
Power connections
Power to the unit is via 2 screw terminals at the centre, with positive to the right nearest Pin 9.
The supply voltage range is 9V to 30V. The unit is designed to be connected to the auxiliary power output on an
associated alarm panel, or separate powered enclosure. For use with intruder alarm panels the power supply must meet
the requirements of EN 50131-6.
For use with Fire alarm panels the power supply must meet the requirements of EN 54-4 and the unit must be mounted
in the same enclosure as the power supply from which it derives its power. Ensure the power source is sufficient to power
all devices connected. See the power requirements in the specification section for more information. The account at the
Alarm Receiving Centre (ARC) should be put “on test” before power up, as signals will be sent following initialisation.
Alarm inputs
The unit has 16 alarm inputs which are presented on screw terminals along the bottom of the unit. These are labelled as
Pin 1-8 and 9 -16
By default the 16 alarm inputs require a positive condition to be presented to send an alarm. (Default = Positive applied).
This can be changed using the Pin Learn button or through the configuration menu. See later section on configuration.
1
2
3
4
5-10
11
13
14-16
Fire alarm (When programed Fire NAK and ACK outputs operate in conjunction with pin 1)
Fire Fault or Hold up alarm
Intruder alarm
Open / Close (Set / Unset) (Func out put can be set up as RPS in conjunction with pin 4)
General alarm
ATS input (BSIA F175 mode) (Can be reprogrammed as a normal alarm pin)
AC Fail alarm (has a 7 minute delay which can be altered in programming)
General alarm
Input (PIN) Use
Fig 3 - Alarm input allocations. (Functions must be agreed with your ARC)
Outputs
Three relay outputs are provided on screw terminals at the top of the unit
Output 1 is Comms, Output 2 is Func, and Output 3 is Fire.
For fire alarm installations the indication of ‘acknowledgement of fire alarm’ and ‘SPT fault’ messages must be provided by
the fire panel into which the SPT is mounted. System fault indications which are notified by the line fault output
(Output 1) must be latched by the fire panel as required by EN 54-21.
See the further sections on outputs for a full explanation.
Serial data connections
The serial data connection labelled TX, RX, B and A is configurable for RS485 or RS232 connection depending on the
panel.
This is done in the configuration menu.
These ports allow serial alarm panel connection. See Panel Upload Download section.
Dial capture
The dial capture (Dial Cap) terminals enable interfacing with an alarm panel’s digital communicator. The alarm panel can
then send SIA, CID or Fast Format messages through the unit to the Alarm Receiving Centre.
Dial capture can also be used for upload download UDL allowing remote access with some types of alarm panel.
Aerial connection
Connect the supplied aerials to the MMCX connectors on the top right of the unit. The aerials should be placed in a
vertical position and slightly apart to ensure a good wireless coverage. Carry out a survey to establish the best location.
If necessary, a selection of high gain and extension aerials can be purchased from the BT Redcare shop at
https://www.btinstallershop.com
8
Mobile 1 Aerial
Mobile 2 Aerial
Programming
Andere Handbücher für Essential Extra
1
Inhaltsverzeichnis
Andere BT Redcare Sicherheitssystem Handbücher
BT Redcare
BT Redcare 3GSTU-12V Fehlerbehebungshandbuch
BT Redcare
BT Redcare SECURE IP Bedienungsanleitung
BT Redcare
BT Redcare Essential Bedienungsanleitung
BT Redcare
BT Redcare Classic Replacement Bedienungsanleitung
BT Redcare
BT Redcare Essential IP Bedienungsanleitung
BT Redcare
BT Redcare 5G Classic STU 11 pin Fehlerbehebungshandbuch
BT Redcare
BT Redcare Advanced Bedienungsanleitung
BT Redcare
BT Redcare UC-351GP/E-UK Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung