BT Redcare SECURE IP Bedienungsanleitung

Quick Start Guide

Redcare Secure

BT Redcare Secure Quick Start Guide.

For detailed installation instructions and speciﬁcation, please consult the online Installation Guide, which can be

downloaded from http://www.redcare.bt.com/partner/install_guides.htm

The Redcare Secure unit is supplied pre conﬁgured for GPRS & PSTN working. (Secure 2 & 3).

For many installations no further conﬁguration changes will be required.

Changing to IP mode

To change the unit to IP mode working (Secure IP) connect a PC to the Ethernet port J600. Link the J903 CONFIG header.

Surf to http://192.168.222.222 and click on the “Quick Start” link. Change the “Interface Combination”

(drop down menu) to “GE (Wireline + Wireless)”.

To revert back to PSTN mode working (Secure 2 & 3) change the “Interface Combination” to “GP (Wireless + Dialup)”

Once conﬁguration is complete, click on the “Save & Reboot” button at the bottom of the screen. Remove the header

J903 and wait 1 minute for the unit to restart.

Quick Start menu settings IP mode (Secure IP)

Page 1

Quick Start menu settings PSTN mode (Secure 2 & 3)

Page 2

Setting Dial Capture Panel Format.

The unit is supplied preconﬁgured for pin only alarm input working. To additionally enable the unit’s dial capture port to

receive SIA, CID or FF from a panel’s onboard dialler, either change the “Panel Type” setting by accessing the Quick Start

menu as above, OR simply conﬁgure the unit with a DTMF telephone as follows.

Connect a DTMF phone to the dial capture port. (Adapter available from BT Redcare) Link the J903 CONFIG header.

Power cycle the unit and wait 15 seconds (6 ﬂashing LED’s) Lift telephone and key # (The unit is now in conﬁguration

mode for 5 minutes or until the telephone handset is replaced).

Set the panel format with the relevant codes as follows.

CID *15 * 1 #

SIA *15 * 20 #

Fast Format (FF) *15 * 11 #

Once conﬁguration is complete, replace the telephone handset and remove link J903.

The unit will restart with the new settings applied.

Learning Pin Polarity.

The Redcare Secure unit is supplied pre-conﬁgured with all alarm input pins being positive applied. However the “Learn”

function can be used to conﬁgure the inputs as required.

Link the J902 LEARN header.

Power cycle the unit and wait 15 seconds until the LEDs scroll the learn pattern (left to right to left) Ensure all alarm

inputs are in their normal state (including pin 4 in the Panel Set [Closed] state) Remove J902 LEARN header and check

that the LEDs brieﬂy blink (Oﬀ – On – Oﬀ) at the point of learning. The Pin polarity has now been learnt by the Redcare

Secure unit.

To ﬁnd out more about Redcare:

call us free on 0800 800 628*

or email redcar[email protected]om

* Calls are free to this number from BT landlines and BT payphones.

However, they are not free to call from mobile phones

the costs will vary between service providers.

Registered oﬃce: 81 Newgate Street, London, EC1A 7AJ

Registered in England no. 1800000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere BT Redcare Sicherheitssystem Handbücher

BT Redcare

BT Redcare UC-351GP/E-UK Bedienungsanleitung

BT Redcare

BT Redcare Essential Extra Bedienungsanleitung

BT Redcare

BT Redcare 5G Classic STU 11 pin Fehlerbehebungshandbuch

BT Redcare

BT Redcare Advanced Bedienungsanleitung

BT Redcare

BT Redcare 3GSTU-12V Fehlerbehebungshandbuch

BT Redcare

BT Redcare Classic Replacement Bedienungsanleitung

BT Redcare

BT Redcare Essential IP Bedienungsanleitung

BT Redcare

BT Redcare Essential Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung