Bulldog Security 1200E Bedienungsanleitung

CONTENTS

REMOTE STARTER

MODELS RS1200/RS1200E

INSTALLATION GUIDE

•

OWNER’S GUIDE

Technical Assistance

All tech personnel are expertly qualified to answer any technical questions.

Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.

Address

288 Canton Avenue • Wintersville, Ohio 43953

Telephone

Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306

System Features....................................... 1

System Components ..................................... 1

Required Tools ........................................ 1

Technical Assistance .................................. 1

Before You Begin ...................................... 2

Precautions........................................... 2

Using your Test Probe ................................. 2

Making Connections .................................... 3

Locating & Making Connections........................ 4-6

Neutral Safety Switch ................................. 6

Connecting Wiring Harness ............................. 6

Antenna Placement ..................................... 7

Anti-Theft System ..................................... 7

Optional Features ................................... 7-9

Operator Programming Instructions ................... 9-10

How to use Your Remote Transmitter.................. 10-11

SYSTEM FEATURES

SYSTEM COMPONENTS

TECHNICAL ASSISTANCE

REQUIRED TOOLS

2 Four-Button Extended Range Remotely start your car to run the heater, air conditioning or defroster from an extended

Remote Control distance.

Keyless Entry Remotely locks and unlocks your power door locks.

Trunk Release/Sliding Door Remotely open your power trunk or your power sliding van door with a push of a button.

Remote Programmable Run Time Remotely program your vehicle to run 5 to 15 minutes.

Run Time Confirmation Remotely check the programmed run time of 5 to 25 minutes.

Ignition Controlled Door Locks A programmable feature that locks and unlocks the doors whtn the brake is pressed or the

ignition is cycled.

Tach/Tachless Option A programmable feature that lets you choose from the easy to install tachless operation or

the wire-in, tach operation.

Parking Light Confirmation Confirms that your vehicle has received a remote signal and will remain on if the engine is

remotely started.

Dome Light Supervision Never walk up to a dark vehicle again. When unlocking the doors by remote control, the dome

light will come on and stay on for 1 minute. This feature will shut off when you activate the

ignition switch or step on the brake.

Automatic Cold Start Remotely program your car to start at a preset temperature. Automatically starts your car in

freezing temperature so you never have a dead battery.

Automatic Start Remotely program your car to start every three hours regardless of the temperature.

Pit Stop Mode Allows you to exit the vehicle while the engine remains running without leaving the key in

the ignition switch.

Extended Range Allows you to operate your system from up to 400 feet away. (800 feet for E Models)

Code Learning Allows your remote starter to learn new remotes, should you want to add remotes, or if remotes

are lost.

Limited Lifetime Warranty Guarantees life-long protection.

Your system includes:

2- Four Button Remote Transmitter

1- Main Control Module

1- 16-Pin Wire Harness

1- 5-Pin Door Lock Harness

6- Heavy Gauge Wires w/ Spade Connectors

1- Hood Pin Switch

1- Extended Range Antenna (E Models Only)

2- Window Antenna Clips (E Models Only)

1- Warranty

1- Warning Sticker for Under the Hood

2-Bulldog Window Decals

1- Installation & Operation Guide

1- Bonus Installation Kit (with selected models)

Should you need help. First check our website at www.bulldogsecurity.com for the most common installation

problems or then our toll-free Tech Support Hotline Monday through Friday 9AM-8PM and Saturday 10AM-4PM

EST at 800-878-8007.

Before you begin, check our website at www.bulldogsecurity.com for complete wiring information for your

vehicle.

You must give the following information:

•Name •The model of the system you are installing

•Telephone Number with Area Code (Fax number if applicable) •The type of assistance you are requesting

•Year, Make, and Model of the vehicle

If you give the above information you will be called in the order your call was received.

You may need a 5/16 inch drill bit when mounting the hood pin switch. In most cases no additional tools

are required, however if the bottom of your dash on the driver’s side will come off you must remove it.

In this case a screwdriver or wrench may be needed.

BEFORE YOU BEGIN

PRECAUTIONS

USING YOUR TEST PROBE

Congratulations, you have purchased one of the most advanced remote starter systems ever made. Your new

remote starter is a technological breakthrough utilizing the most advanced, state-of-the-art technology

and components. It is computer controlled and manufactured in the U.S.A. The dependability and variety of

features make Bulldog Security the leader in the industry. Enjoy your new remote starter for years to

come!

This remote system is designed to start your vehicle by sending a command signal from the remote transmitter

or by programming automatic temperature start. It is required that your installation be done in a well-

ventilated area. It is the responsibility of the owner to ensure that the remote system is not used to

start the vehicle in an undesired location.

It is recommended that a carbon monoxide detector be installed in the living area near the location where

the vehicle may be garaged.

Since there are many different makes and models of vehicles, for a more complete wiring chart, visit our

website, www.bulldogsecurity.com to access your vehicle’s colors and location of wires.

Read this manual thoroughly BEFORE starting the installation. Most newer vehicles may have a factory anti-

theft system. If you vehicle is equipped with this system, an additional module, Part #781 or #791, will

be required. Contact 800-659-0764 to order this item. Please do not skip any steps. Mount the control

module under the driver’s dash inside the vehicle after all connections have been made. Do not mount the

control module in the engine compartment.

TACH/TACHLESS OPERATION

In most cases the decision to go with tachless mode will save time during the installation. If your vehicle

is hard-starting then you should use tach mode.

MAKE SURE YOU PLACE THE WARNING STICKER UNDER THE HOOD.

Should you need help. First check our website at www.bulldogsecurity.com for the most common installation

problems or then our toll-free Tech Support Hotline Monday through Friday 9AM-8PM and Saturday 10AM-4PM

EST at 800-878-8007.

Before you begin, check our website at www.bulldogsecurity.com for complete wiring information for your

vehicle.

You must give the following information:

•Name •The model of the system you are installing

•Telephone Number with Area Code (Fax number if applicable) •The type of assistance you are requesting

•Year, Make, and Model of the vehicle

If you give the above information you will be called in the order your call was received.

This system is designed for use with vehicles equipped with fuel-injected,

gasoline engines with automatic transmissions only.

SAFETY FIRST!

Never remotely start your vehicle indoors, with the keys in the ignition or unless the transmission

is in park. A periodic safety check is recommended to ensure that your system is in proper working

order.

DO NOT use mechanical wiring connections, such as crimp or snap together wire connectors.

Instead, follow the instructions on page 3-4.

DO NOT disconnect the battery if the vehicle has an anti-theft-coded radio or is equipped with

an airbag. Doing so may cause a warning light to be displayed which may require a trip to the

dealer to be corrected.

DO NOT leave the interior or exterior lights on for an extended period of time as it may cause

battery drain. Remove the dome light fuse from the vehicle’s fuse box. NOTE: Starter systems do

not work well with a partially discharged battery.

WARNING!

GENERAL MOTORS REAR WHEEL DRIVE VEHICLES AND DODGE DAKOTAS

All General Motors rear wheel drive vehicles and Dodge Dakotas built prior to 1996 do not have

an electrical neutral safety switch. They have a mechanical neutral safety switch. The mechanical

neutral safety switch operates as follows.

a)The key will only turn to the start position when the gear selector is in park or neutral.

b)The key can only be removed from the ignition switch when the gear selector is in the park

position.

You must use special precautions with this system.

To operate your test probe, connect the black clip to a good chassis ground. Connect the red clip to a good

12V positive source. If the test probe is connected correctly, both the green and the red lights will be dimly

illuminated. If a positive source is probed, the red light will glow bright and the green light will go out.

If a negative source is probed, the green light will glow bright and the red light will go out.

MAKING WIRING CONNECTIONS

NOTE: In most cases you should not cut your vehicle wire in two.

1. Strip back two inches of insulation on the wire from the remote starter.

2. Strip back one inch of insulation on the wire you need to connect to.

3. Separate the vehicle wire as shown. Make the separation large enough to fit the other

wire through.

4. Insert the wire(s) from the starter through the hole as shown. If two or more wires

are inserted, wrap them in opposite directions.

6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side

of the connection. First pull the wire that you have just connected along side the wire

you connected to, tape and wire tie them together. Use this method for all connections.

CAUTION: All wires must be wrapped with tape and wire tied.

5. Wrap the wire around one side then the other and finally around itself as shown.

Two Inches of Bare Wire

One Inch of Bare Wire

Wire Tie

Electrical Tape

1. When tying two separate wires together at their ends, strip back one inch of insulation on

both wires and separate the strands of wire as shown below.

MAKING END TO END CONNECTIONS

Use this method ONLY when connecting two separate wires end to end.

4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection.

Secure with wire ties as shown.

3. Lay upper twisted pair of wires over right

wire as shown. Bring lower twisted pair

of wires up to meet the left wire as

shown.

2. Twist upper wires together, twist lower

wires together as shown.

Use this method ONLY when connecting two separate wires end to end.

Wire Tie

Electrical Tape

Wire Tie

LOCATING & MAKING CONNECTIONS

Please see the wiring chart on this website.

Most of the wires you will be using will be in a taped or nylon sleeve coming from the ignition switch.

You must find and remove about six inches of this outer covering for testing and connecting.

CONSTANT POWER (+12V, key in any position including off)

Make all connections as close to the ignition switch as possible.

These wire(s) are in your vehicle’s main ignition harness, usually located in the steering column coming

from the ignition switch. Probe each wire with your provided test probe. The correct wire(s) will show

+12V and the RED light will glow bright on the test probe when the ignition switch is in these 5 positions

(ACC-LOCK-OFF-RUN-CRANK).

IGNITION HARNESS

UNDER DASH

1. If your vehicle has only (1) constant power wire, attach both heavy

gauge RED wires to it.

2. If your vehicle has (2) constant power wires, attach one RED wire to

each.

IGNITION WIRE(S) (+12V in run and crank position only)

Make all connections as close to the ignition switch as possible.

The ignition wire(s) are also located in the main harness coming from the ignition switch. Check your

chart for probable colors and probe each wire with your provided test probe. The correct wire(s) will

show +12V and the RED light will glow bright only when the ignition switch is in the RUN AND CRANK

positions. The correct wires will not show +12V when in the OFF or ACCESSORY position. Most Ford, GM,

and Chrysler vehicles have at least two (2) ignition wires. Most foreign vehicles have only one (1).

Note: Remove any paint below

the spade connector.

Factory Bolt

Spade Connector

Black Ground Wire

1. If your vehicle has only one (1) ignition wire, as most 1993 and older domestic and import vehicles

do, connect the heavy gauge WHITE wire to it.

2. If your vehicle has two (2) ignition wires, as most 1994 and newer vehicles do, connect the heavy

gauge RED with WHITE stripe wire to the Ignition 2 wire.

3. If your vehicle has three (3) ignition wires, as some newer GMs, Fords and Chryslers do, connect the

heavy gauge WHITE wire to the third ignition along with the Ignition 1 wire.

ACCESSORY WIRE(S) THAT POWER THE HEATER/BLOWER MOTOR

(+12V in run or on positions) This wire is also in the main ignition switch harness. Make this connection as

close to the ignition switch as possible.

Most vehicles will have one (1) accessory wire; however some Fords, newer GM vehicles and Chrysler 94 and up will

have two (2) or more accessory wires. Check your wire color chart and then verify these wire(s).

The correct

wire(s) will show +12V and the RED light will glow bright

when the ignition switch is in the RUN or ON positions.

This wire(s) will not show +12V when the ignition switch is in any other position.

1. If your vehicle has only one (1) accessory wire connect the heavy gauge WHITE WITH BLACK STRIPE wire to this

wire.

2. If your vehicle has two (2) accessory wires, connect the WHITE WITH BLACK STRIPE wire to both accessory wires.

3. If your vehicle has three (3) accessory wires, connect the WHITE WITH BLACK STRIPE wire to all three.

STARTER/CRANK WIRE (+12V in the start position only)

Make all connections as close to the ignition switch as possible.

The starter/crank wire is also in the main harness. Check your chart for probable colors and verify the wire

. The

correct wire(s) will show +12V and the RED light will glow bright

only in the crank position. This wire

will not show +12V in any other position. Attach the YELLOW WITH BLACK STRIPE wire to it.

NOTE: Most Nissans will have two (2) starter/crank wires. Both must be connected to the YELLOW WITH BLACK STRIPE

wire.

CHASSIS GROUND

Locate an easy to get to bolt or screw located under the driver’s side of the dash and attach the BLACK ground

wire from the 16-pin harness securely as pictured. A good ground is vital for your system to operate correctly.

FACTORY ALARM SHUT DOWN WIRE (FASD) (-)

If your vehicle is equipped with a factory alarm system (as most new model vehicles with a factory keyless

entry are) and you can disarm your factory alarm by using your key in the door. Check the owner’s manual or

contact your dealer to see if your vehicle is so equipped. Probe for a small gauge wire (usually found in

the driver’s side kick panel) that shows (-) ground and the GREEN light will glow bright when the door lock

cylinder is turned to the unlock position using the key and will show +12V and the RED light will glow bright

before turning the key. NOTE: Some factory disarm wires remain neutral (both the GREEN and the RED lights

will be dimly illuminated) before you turn the key to unlock instead of +12v positive. Connect the RED WITH

BLACK STRIPE wire from the 16-pin harness to this wire. See chart, page 21 for listing by manufacturer.

IGNITION OUTPUT (-) (Security bypass output wire)

This wire will be used to operate the security bypass module, VATS-WR, #781 or the #791 module. This

WHITE wire holds a ground output the entire time the remote starter is activated. Connect this wire to

the WHITE wire on the bypass module to control when the bypass is on and off.

HOOD PIN SWITCH (-)

This feature will keep the engine from starting, or shut off the engine when the hood is opened.

Locate a good chassis ground, if at all possible do not install the pin switch in the rain gutter.

Drill a 5/16 hole, insert the pin switch into the hole and tighten. Check for the hood adjustment,

there is approximately 1/4” adjustment in the pin switch. Close the hood easy, making sure that

the pin switch is not keeping the hood from closing all the way, if it does, cut off approximately

1/8” of the black plastic off of the top of the hoodpin switch and try closing the hood again.

Check to make sure that the hoodpin switch remains neutral when the hood is closed and shows ground

when the hood is open. Route the BLACK WITH BLUE STRIPE wire from the 16-pin harness through the

firewall and connect it to the bottom of the hood pin switch.

BRAKE INPUT (+)

The brake wire is located on the switch near and above the brake pedal.

The correct wire will show +12V and

the RED light will glow bright

only when the brake is pressed. Connect the BLUE WITH BLACK STRIPE from the 16-

pin harness to this wire.

TACH INPUT (Optional)

If you have chosen the TACHLESS start option, simply proceed to the next step and skip the following

instructions. Make sure to tape the BLACK WITH WHITE STRIPE wire if not used. For TACH mode connect

the BLACK WITH WHITE STRIPE wire from the 16-pin harness to the negative side of the coil or the

tach wire at the coil pack under the hood. To find the coil pack follow the spark plug wires back

to their beginning point. To operate in tach mode, make sure to program tach option, see programming

tach option page 10.

NEUTRAL SAFETY SWITCH

CONNECTING THE WIRING HARNESS

PARKING LIGHTS (+12V only with parking lights on)

Turn the parking lights to the ON position. (NOT YOUR HEADLAMPS).

Probe the wire(s) coming from your headlamp control switch.

The correct wire will show +12V and the RED light will

glow bright

only when the parking lights are ON. Connect the

BROWN wire from the 16-pin harness to this wire. If this wire

tests as a (-) negative, the GREEN light glows bright. See

negative parking light diagram.

DO NOT USE THE RED WIRE, TAPE OFF.