Bushnell 119600 Installationsanleitung

FAQ

All my pictures are coming out black at night.

This is a common problem if the setting of the camera are not set up correctly. We will

need to make sure the Time, Date, Day Time setting are correct. To do this you will need

to turn the unit on and log into the camera. Then select the Menu option, the first

selection will be set Time. If this is not done you will need to hit Enter, then enter the

correct time. Once the time is entered we will need to hit the down button to the next

entry.

Battery life short on Trophy Cam.

Expected battery life depends on temperature and number of images. Bushnell expects

the camera to take several thousand images before the batteries would die. If your battery

life is shorter, check the following:

Make sure you have used new alkaline or lithium batteries. Bushnell recommends 8

Energizer Lithium AA batteries in all Trophy Cams.

Make sure that the power switch is turned to the “On” position and that the camera

was not left in “Setup” mode while in the field.

Make sure that you are using a good quality SD card in your camera. Bushnell

recommends San Disk Brand SD Cards. Unfortunately, poor quality SD cards can make

your camera have a much shorter battery life.

Camera takes continuous images of no subject

A camera has what is known as a “false trigger” if the PIR sensor thinks that there is

motion and heat in front of the camera lens when there is no subject in the image. These

“False Triggers” are the result of placing the camera in an environment where there is

motion associated with tree branches creating motion in front of the camera or an area

where there is high heat in the foreground and any motion from wind could set off the

camera. Setting a camera up over water is also a potential cause for this issue.

To remedy this situation try moving the camera to an area that does not have any of these

issues or try changing the sensor level on the menu settings.

If the camera continues to take images when there is no subject in them, try placing the

camera in an inside environment and aiming at a location where there is no motion. If the

camera continue to show issues, then there is probably an electronic component issue. If

this is the case, please contact our customer service to send the camera back for repair.

Can I change the resolution on any of the units?

The resolution can not be changed on any of the trail cameras.

Can I use a higher capacity SD card than what comes with

the unit?

You can use a higher capacity card than what comes with the unit. We have tested cards

up to 512MB. Any card larger has not been tested.

Can I use rechargeable batteries in my camera?

Since most rechargeable batteries operate at 1.2V instead of 1.5V we cannot recommend

rechargeable batteries. The Bushnell Trail Cameras are designed to operate at 6V by

using a mininum of 4-AA batteries.

Field Scan (Time Lapse) not working properly

Make sure that the stop and start times of Field Scan "A" and "B" do not overlap. (for

example, do not set the start time of "B" to 8AM if the start time of "A" is 10AM).

When Using Field Scan in Video Mode, the smallest interval time available is 5 minutes,

to avoid potential overheating of the batteries and electronic components, which could

cause operational failure or damage to the camera. In still photo mode a 1 minute interval

can be set.

How can I print my images?

You can print your images directly from your computer if you have an SD card slot or

external reader. You can also take the SD card to a photo center and have them printed.

How do I set the time for the day or night mode?

Use miltary time to set the start and stop times for day or night. This is only applicable if

the switch for imaging is set to "Day" or "Night" mode. In 24 hour mode, the camera

does not need to know when the day begins or ends.

How do I use the new Camera Name Input on the Bushnell

Trophy Cam HD?

After selecting the Camera Name parameter (the only setting is "Input"), press OK. If

necessary, delete the previous or default name by pressing the RIGHT key until the

backspace symbol (<- ) (located between letters "A" & "B", also between "j" & "k") is

highlighted, then keep pressing OK. Select (highlight) each alphanumeric character you

want, using the LEFT/RIGHT keys, and pressing OK after each one to set it. When

finished naming the camera, press MENU to save the name to memory.

How do I use the new Coordinate Input to set up the Geotag

setting on the new Trophy Cam HD?

After selecting the Coordinate Input parameter, press UP or DOWN to select the On

setting and press OK. The latitude and longitude for any location where you plan to place

the camera can be obtained at many websites, for example:

http://itouchmap.com/latlong.html. You can enter a nearby street address, just zip code,

or use the various types of maps to locate the approximate position.

How do I view my images on the SD card?

To view the images on the SD card, turn the unit off and remove the SD card. Insert the

SD card into your PC and view images. You may have to purchase an SD card reader

($10-$15 retail). Note: If you have a digital camera or Palm/Pocket PC that accepts SD

cards, you may be able to view the photos on those devices.

How long is the battery life for the Bushnell Trial Cameras?

Under normal scouting conditions (40 degrees F and above), the batteries should last over 30

days. We have had a unit running over 7 days in single digit temperatures and the camera was

still recording images.

On a Trail Scout/Sentry: 30 days or 300 photos

Trophy cam: 6 months or 700 photos w/ 4 AA’s; 12 months or 1400 photos w/ 8 AA’s.

How many images can I fit on a 32MB card?

Model#11-9600 should hold approximately 400 images on a 32MB card. Model#11-9800

and #11-9900 should hold approximately 120 images on a 32MB card.

I am having trouble viewing my video clips from my Trophy

Cam Model 119466, 119467, 119437, 119447, 119476 or

119477.

The .avi/.mov video files may be viewed with the Windows Media Player on PCs with

Windows 7. If your computer is running an older version of Windows, or you are on a

Mac, and you don’t already have a compatible video player, you can download a free

version of the DivX player from www.divx.com.

Make sure you are using an SDHC SD card. Bushnell recommends SanDisk brand SDHC

SD cards.

I cannot delete the images off of the SD card.

If you can not delete your images off your SD card, please look for the small white button

on the card that slides. It could be slid to the locked position, therefore not allowing you

to delete the pictures. Slide to the unlocked position and try to delete the photo.

I have locked myself out of my trail camera, what can I do

now?

If you are unable to log into your trail Camera you will need to call Bushnell Technical

Support. Please call 1-800-423-3537, then option 2 for further assistance.

If a majority of my images are over exposed what should I

do to try to alleviate this?

This is most often caused by the camera being positioned in a very enclosed area where

the target being photographed is very close to the camera. To alleviate this you can either

reposition the camera to point to a more open area or move it further up the tree and angle

it downward to the area that you wish photographed.

If I use the nightvision mode on unit 11-9900, what will the

pictures look like?

If you use the nightvision mode for still pictures or movie clips, remove the filter. The

pictures or movie clips will be in black and white.

Image/Video Dissatisfaction

Night images or video appear dark

Check to see if battery power is full. Camera will stop flashing near end of battery

life.

Make sure that the camera is aimed at your intended target area within 45’ (14m)

of the camera.

Please note that in the multi shot mode, some images may appear darker than

others due to the quick response and reshooting of the camera.

Daytime images or video appear dark

Make sure that the camera is not aimed at the sun or other light sources during the

day.

Night images or video appear bright

Make sure that the camera is aimed at your intended target area within 45’ (14m)

of the camera.

In cases where the subject is closer than 10’ (3m) of the camera, some images

may appear too bright.

Daytime images or video appear bright

Make sure that the camera is not aimed at the sun or other light sources during the

day.

Red/Green Images

Under certain lighting conditions, the sensor can become confused resulting in

poor color images.

If this is seen on a consistent basis, then the sensor may need servicing. Please

contact our customer service.

Short Video Clips—not recording to the length set

Check to make sure that the SD card is not full.

Make sure that the camera has good batteries in it. Near the end of the battery life,

the camera may choose to record shorter video clips to conserve power.

My unit is not writing images to the SD card?

If your unit is not writing images to the SD card please send the unit into the repair center

for a technician to review. Click the 'more info' button below for instructions on returning

product.

On some trail cams what is the Day Time Setting?

This setting allows you to tell the trail camera what your day light hours in your area are.

This on some models determines when it will use the LED’s for a light source versus the

flash and on other models this setting will determine when a filter is in place to allow

proper night vision photos.

Photos Do Not Capture Subject of Interest

1. Check that the “Sensor Level” (PIR sensitivity) parameter setting. For warm

environmental conditions, set the Sensor Level to “High” and for cold weather

use, set the sensor for “Low”.

2. Try to set your camera up in an area where there is not a heat source in the

camera’s line of sight.

3. In some cases, setting the camera near water will make the camera take images

with no subject in them. Try aiming the camera over ground.

4. Try to avoid setting the camera up on small trees that are prone to being moved by

strong winds.

5. Remove any limbs which are right in front of the camera lens.

PIR Sensor LED Flashes/Doesn’t Flash

When the camera is in the “Setup” mode, a special LED on the front of the camera will

flash when it senses motion. This is for setup purposes only and will help the user aim the

camera.

During use, the LED will not flash when the camera takes an image. This is to help keep

the camera hidden from game.

Still Photo and/or Video Quality Problems

Night photos or videos appear too dark

Check the battery indicator icon to see if battery power is full. The flash will stop

operating near the end of the battery life.

You will get the best results when the subject is within the ideal flash range, no

farther than 45’ (14m) from the camera. Subjects may appear too dark at greater

distances.

Please note that when the Capture Number parameter is set higher than “1 Photo”,

or with very short Interval settings, some images may appear darker than others

due to the quick response and rapid retriggering of the camera, allowing less time

for the flash to fully recharge before firing again.

Daytime photos or videos appear too dark

Make sure that the camera is not aimed at the sun or other light sources during the

day, as this may cause the auto exposure to produce darker results.

Night photos or videos appear too bright

You will get the best results when the subject is within the ideal flash range, no

closer than 10’ (3m) from the camera. Subjects may appear too light at closer

distances.

Daytime photos or videos appear too bright

Make sure that the camera is not aimed at the sun or other light sources during the

day.

Photos with streaked subject

In some cases with low lighting conditions and fast moving subjects, the 5MP or

8MP resolution settings may not perform as well as the 3MP setting.

If you have multiple images where fast moving subjects produce streaks on the

photo, try the 3MP setting instead.

Red, green or blue color cast

Under certain lighting conditions, the sensor can become confused resulting in

poor color images.

If this is seen on a consistent basis, then the sensor may need servicing. Please

contact Bushnell customer service.

Short video clips—not recording to the length set

Check to make sure that the SD card is not full.

Make sure that the camera has good batteries in it. Near the end of the battery life,

the camera may choose to record shorter video clips to conserve power.

Trophy Cam date/time Stamp not appearing on images

Make sure that the “Time Stamp” setting is set to “On” in the Menu.

Trophy Cam LCD Screen Issues

1. LCD screen powers on but no text is present.

oWhen moving the switch from “Off” to “Setup” or “On”, the user should

make sure that the switch stops in a positive position to ensure the proper

mode.

oWhen moving the switch from “On” to “Setup”, the user should first move

the switch directly to “Off” before moving to “Setup”.

2. LCD screen shows a faint black line after turning from “Setup” to “On”.

oThe LCD will turn off when you slide the switch to the “On” position. In

some cases, this black line will appear and will fade in about 1 second.

This is normal and the camera will function properly.

3. Screen will come on and power off

oMake sure that you have installed the SD card correctly.

Trophy Cam stops taking images or won’t take images

1. Please make sure that the SD card is not full. If the card is full, the camera will

stop taking images.

2. Check batteries to make sure that they are new alkaline or lithium AA batteries.

See note about short battery life.

3. Make sure that the camera power switch is in the “On” position and not in the

“Off” or “Setup” modes.

4. Make sure that you are using a good quality SD card in your camera. Bushnell

recommends San Disk Brand SD Cards.

Trophy Camera is taking images without subject in the field

of view

1. Check the PIR Sensitivity Level Setting. For warm temperature use, set the sensor

to “High” and for cold weather use, set the sensor for “Low”.

2. Try to set your camera up in an area where there is not a heat source in the

camera’s line of sight.

3. In some cases, setting a camera near water will make the camera take images with

no subject in them. Try aiming the camera over ground.

4. Try to avoid setting the camera up on small trees that are prone to being moved by

strong winds.

5. Remove any limbs right in front of the camera lens.

Trophy Camera won’t power up

1. Make sure that you have installed at least 4 batteries in the battery compartment

all stacked together at the top of the compartment.

oBushnell recommends 8 Energizer Lithium AA batteries in all Trophy

Cams.Make sure that the batteries are installed correctly. See manual.

2. When moving the switch from “Off” to “Setup” or “On”, the user should make

sure that the switch stops in a positive position to ensure the proper mode.

3. When moving the switch from “On” to “Setup”, the user should first move the

switch directly to “Off” before moving to “Setup”.

Trophy Camera won’t retain settings

1. Make sure that you have saved the changes that you make during the menu setup

of the camera.

2. If you don’t select and save these settings, the camera will revert back to the

default settings.

What do I do if I forget my password?

Password recovery can be facilitated by contacting our customer service line at 1-800-

423-3537 pressing option 2 in the main menu. Your units serial number will be needed

for this process.

What happens if I take off the filter on Model#11-9900?

If you take the filter off the 11-9900, the pictures taken, both during the day and at night,

will be in black and white (nightvision mode).

What is the battery life for a Bushnell Trail Sentry?

The Bushnell Trail Sentry has a battery life up to 60 days.

What is the resolution of the video clips on the Trophy cam?

On High Quality: 640X480 and Low Quality : 320X240

What is the Trophy PIR Sensor LED Use

1. When the camera is in the “Setup” mode, a special LED on the front of the

camera will flash when it senses motion. This is for setup purposes only and will

help the user aim the camera.

2. During use, the LED will not flash when the camera takes an image. This is to

help keep the camera hidden from game.

What should I do if I have forgotten my password?

If you have forgotten your password, the product will need to be returned to our repair

center. Click on the 'more info' button below for instructions on returning your product.

What should I do if my pictures are out of focus?

If your pictures are out of focus, please call customer service. The customer service

representative will ask you to email them a sample picture. It's possible your unit may

need to be sent to our repair center for a technician to review.

What should I do if the unit locks up and the display will not

change?

If your unit locks up and the display will not change, remove one battery to break the

connection. Put the battery back in and then turn the unit back on.

What type of batteries should I use in my Trophy Camera?

Bushnell recommends 8 Energizer Lithium AA batteries in all Trophy Cams.

What type of card should I use with my Bushnell Trail

Camera?

Bushnell recommends San Disk Brand SD Cards.

What will the pictures look like if taken at night on the 24

hour mode or on night mode?

You can take night pictures on any unit. The pictures will be in color with the flash. They will look like

any picture taken at night with a flash. The Model#11-9900 can take night pictures. With the filter on,

they will be color pictures. To take night vision pictures that are black and white, you have to take off

the filter.

Dieses Handbuch passt für folgende Modelle

Andere Bushnell Scouting-Kamera Handbücher

Bushnell

Bushnell X-8 TRAIL CAM 119327 Bedienungsanleitung

Bushnell

Bushnell 119904S Bedienungsanleitung

Bushnell

Bushnell 119466 Bedienungsanleitung

Bushnell

Bushnell TROPHY CAM HD AGRESSOR 119873C Bedienungsanleitung

Bushnell

Bushnell CELLUCORE 20 SOLAR Bedienungsanleitung

Bushnell

Bushnell TROPHY CAM 119425C2 Bedienungsanleitung

Bushnell

Bushnell TROPHY CAM HD VITAL 119726C Bedienungsanleitung

Bushnell

Bushnell 119908D Bedienungsanleitung

Bushnell

Bushnell TROPHY CAM 119425C Bedienungsanleitung

Bushnell

Bushnell NatureView 119739 Bedienungsanleitung

Bushnell

Bushnell Trophy Cam 119435 Bedienungsanleitung

Bushnell

Bushnell Trail Scout 11-9600 Bedienungsanleitung

Bushnell

Bushnell TROPHY CAM Bedienungsanleitung

Bushnell

Bushnell CELLUCORE 20 Bedienungsanleitung

Bushnell

Bushnell 119734C Bedienungsanleitung

Bushnell

Bushnell Trailscout 119700 Bedienungsanleitung

Bushnell

Bushnell CELLUCORE 30 Bedienungsanleitung

Bushnell

Bushnell 119437 Bedienungsanleitung

Bushnell

Bushnell TROPHY CAM 119628C Bedienungsanleitung

Bushnell

Bushnell TRAIL SENTRY 119320C Bedienungsanleitung

Bushnell

Bushnell 119636C Bedienungsanleitung

Bushnell

Bushnell TrailScout 119835 Bedienungsanleitung

Bushnell

Bushnell CELLUCORE 20 Bedienungsanleitung

Bushnell

Bushnell 119599C2 Bedienungsanleitung

Beliebte Scouting-Kamera Handbücher anderer Marken

Nestbox

Nestbox C13 Bedienungsanleitung

Wildview

Wildview STC-TGL1 Bedienungsanleitung

Stealth Cam

Stealth Cam CORE STC-Z3IRTL Bedienungsanleitung

Suntek

Suntek HC-800M Bedienungsanleitung

Spypoint

Spypoint G4 Bedienungsanleitung

Duramaxx

Duramaxx 10029765 Bedienungsanleitung

Brecom

Brecom C2400 Bedienungsanleitung

BlazeVideo

BlazeVideo A280W Bedienungsanleitung

Bestok

Bestok 5210GM Bedienungsanleitung

GardePro

GardePro X60P Bedienungsanleitung

Delta-Opti

Delta-Opti HC-SG880MK-18MHD Bedienungsanleitung

PNI

PNI HUNTING 280C Bedienungsanleitung

Muddy

Muddy Pro-Cam 14 Bedienungsanleitung

Bresser

Bresser 3310006 Bedienungsanleitung

Recon Outdoors

Recon Outdoors HS410 Bedienungsanleitung

Braun

Braun 57660 Bedienungsanleitung

Wildgame

Wildgame Shadow Bedienungsanleitung

Spypoint

Spypoint FLEX Bedienungsanleitung