BWI Eagle AIR-EAGLE XLT PLUS Bedienungsanleitung

AIR-EAGLE XLT PLUS

461-1400-DC

900 MHz RF Transmitter

Document Date: 11/10/2022

Product Rev: 8

461-1400-DC

WARRANTY STATEMENT

BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and installed, will be free

from defects in material and workmanship for a period of 1 year after date of purchase. Said warranty to

include the repair or replacement of defective equipment. This warranty does not cover damage due to

external causes, including accident, problems with electrical power, usage not in accordance with product

instructions, misuse, neglect, alteration, repair, improper installation, or improper testing. This limited

warranty, and any implied warranties that may exist under state law, apply only to the original purchaser of

the equipment, and last only for as long as such purchaser continues to own the equipment. This warranty

replaces all other warranties, express or implied including, but not limited to, the implied warranties or

merchantability and fitness for a particular purpose. BWI Eagle makes no express warranties beyond

those stated here. BWI disclaims without limitation, implied warranties of merchantability and fitness for a

particular purpose. Some jurisdictions do not allow the exclusion of implied warranties so this limitation

may not apply to you. To obtain warranty service, contact BWI Eagle for a return material authorization.

When returning equipment to BWI Eagle, the customer assumes the risk of damage or loss during

shipping and is responsible for the shipping costs incurred.

SIGNAL RANGE

Max range statements are estimates based on a clear line of sight with few interferences. Actual range will

vary based on transmitting power, orientation of transmitter and receiver, height of transmitting and

receiving antennas, weather conditions, electronic interference, terrain, and physical obstacles, including

but not limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills, mountains).

WIRELESS STOP, ASTOP, and E-STOP SYSTEMS

Wireless E-STOP systems should never be considered a primary life-saving device.

At least one hard-wired switch must be available in the event the wireless system is

not operational. Failure to comply may result in serious injury or death to personnel

and damage to equipment.

Wireless STOP and ASTOP transmitters are not failsafe emergency stop controls.

They are NOT to be used as a life-saving device. They are designed for wireless

control of equipment or vehicle remote operation. Failure to use as intended may

result in serious injury or death to personnel and damage to equipment.

461-1400-DC

INTRODUCTION

The Air-Eagle XLT Plus is an RF system designed for extra-long range wireless remote control of

electrical apparatus in a variety of industrial applications. Systems can consist of any number of receivers

and handheld or contact input transmitters working together to create a long-range radio frequency

system that operates hazardous or hart-to-reach equipment from safe, convenient locations.

Eight user selectable frequencies allow multiple systems to be used in the same area without

interference.

This transmitter is equipped to send four independent dry-contact input commands to an Air-Eagle XLT

Plus receiver located up to 5000 feet away. Longer ranges can be achieved with external antennas (See

ACCESSORIES section). The Air-Eagle SR Plus/XLT/XLT Plus transmitter utilizes spread-spectrum

technology and provides the utmost in security and reliability.

INSTALLATION

1. DISCONNECT power from all equipment before proceeding with installation.

2. Mount the transmitter in a convenient location.

3. Install input control wiring to the terminal strip. (See TERMINAL STRIP WIRING section.)

4. Attach rubber duck antenna or coax from external antenna to connector on side of enclosure.

5. Connect supplied power input cable to your external power source.

GENERAL OPERATION

A closure on any input transmits its channel command to activate the corresponding relay in the remote

receiver. The transmission continues as long as the input is closed and ceases when the input opens.

461-1400-DC

TERMINAL STRIP WIRING

Terminal 1

CH1 Dry Contact Input (Common)

Terminal 2

CH1 Dry Contact Input

Terminal 3

CH2 Dry Contact Input (Common)

Terminal 4

CH2 Dry Contact Input

Terminal 5

CH3 Dry Contact Input (Common)

Terminal 6

CH3 Dry Contact Input

Terminal 7

CH4 Dry Contact Input (Common)

Terminal 8

CH4 Dry Contact Input

Terminal 9

(-) 9-36VDC Input

Terminal 10

(+) 9-36VDC Input

APPROVALS

United States (FCC)

MCQ-XBPSX

Canada (IC)

1846A-XBPSX

Australia

RCM

Brazil

ANATEL: 05774-16-01209

461-1400-DC

FREQUENCY & DIGITAL ADDRESS SET-UP

The unit is shipped from the factory

with all SEL1 and SEL2 switches in

the open positions. It is operating

on Frequency 1 and Digital

Address 1. To change default

settings, follow the instructions

below:

*Note –only change the digital

address if using with a digitally

addressable receiver. Otherwise,

the digital address must be kept at

the default of Digital Address 1.

1. *IMPORTANT*

Disconnect power from

unit.

2. Remove top cover.

3. Select desired frequency

and/or digital address

using the table.

4. Reattach cover.

5. Reconnect power to unit.

6. Programming is complete.

FREQUENCY SETUP (SEL1)

NETWORK

FREQUENCY

SW1

SW2

SW3

1 (default)

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

Note - SEL1 SW4 not used on this model. Leave in OPEN

position

DIGITAL ADDRESS SETUP (SEL2)

DIGITAL

ADDRESS

SW1

SW2

SW3

SW4

1 (default)

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

OPEN

CLOSED

Note - SEL2 SW5-7 not used on this model. Leave in OPEN

position

461-1400-DC

CONTROLS & INDICATORS

POWER/TX

LED1

Dual color LED illuminates red while unit is booting up, changes to green

when boot-up is successful and unit is ready to operate.

If this LED fails to turn green, power unit off for 15-20 seconds, then

reapply power.

Input Channels

1-4

Transmits individual RF codes to the receiver.

SEL1

Dip switch bank for frequency selection.

SEL2

Dip switch bank for digital address selection.

RF2

RF module that transmits data.

461-1400-DC

SPECIFICATIONS

Power Supply

9-36 VDC, 16 W, 50/60 Hz

Fuse Protected

2 amp

Transmit Data

Four Independent Dry Contact Inputs

Frequency

902-928 MHz Spread Spectrum

RF Output Power

1 Watt

Range

Up to 5000 feet (Up to 10 miles with external

antenna - see accessories)

RF Networks

Eight Independent Network Frequencies

Operating Temperature

-40oF to +185oF

Enclosure

Polycarbonate, IP66 (NEMA 4)

*Note: Max range statements are estimates based on a clear line of sight with few

interferences. Actual range will vary based on transmitting power, orientation of

transmitter and receiver, height of transmitting and receiving antennas, weather

conditions, electronic interference, terrain, and physical obstacles, including but not

limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills,

mountains).

ACCESSORIES

STANDARD ANTENNA (INCLUDED)

900MHz TNC Portable “Rubber Duck” Antenna

49-1103

MOBILE/BASE ANTENNAS (OPTIONAL)

Used to help achieve max range in non-line-of-sight and line-of-sight applications.

Contact BWI Eagle for recommendations.

900MHz Thru-Hole/Bracket Mount Mobile Antenna

49-2101

900MHz Magnet Mount Mobile Antenna

49-2102

900MHz Omni Directional Base Antenna

49-3101

900MHz Yagi Directional Base Antenna

49-3102

HIGH QUALITY COAX CABLE

Used to connect external antennas to control unit.

Flex Coax Cable w/Connectors

(Available in 5’, 15’, 25’, 30’, 40’, 60’, 80’, and 100’ lengths)

49-4000-XX

(XX = length in feet)

BULKHEAD EXTENSION

Used to provide an external antenna connection when mounting control unit

inside another enclosure.

TNC Male to TNC Bulkhead Cable Assembly

(Available in 2’, 4’, and 7’ lengths)

49-5004-X-ISO

(X = length in feet)

461-1400-DC

DIMENSIONS

Andere Handbücher für AIR-EAGLE XLT PLUS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere BWI Eagle Sender Handbücher

BWI Eagle

BWI Eagle AIR-EAGLE XLT 441P-HH-4-002-CL Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE XLT Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE XLT PLUS 461-HH-1 Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE XLT Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE XLT Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE XLT Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-10100-AC Handbuch

BWI Eagle

BWI Eagle 441-10100-AC Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000-RB-N4-120VAC Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000-SSB-120VAC Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE XLT Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE XLT Handbuch

BWI Eagle

BWI Eagle 441-10100-AC Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE XLT PLUS 461-1400-AC Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE XLT 441UP-HHED-4-001 Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-HH-9 Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE XLT Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE XLT 44-10100-120I-AC Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-1400-4B-120VAC Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-HH-4-VBR Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-1420-2B-120VAC Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE XLT 441AN/D-1000-120VAC Handbuch

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-HH-1 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung