CablesPlus SCM-1 Bedienungsanleitung

VIDEO MOUNT PRODUCTS

Instruction Sheet For:

SCM-1

Step 1

Before starting, lay out all parts to your mount and match them to the

parts list provided. Verify that you have all your parts before attempt-

ing to assemble the mount.

Step 2

Lay the ceiling plate onto the ceiling grid so the lips of the ceil-

ing plate rest on top of the ceiling runners. Tighten adjustable screws

to hold the plate in place. Slide the carriage into the desired

position and use the ¼” – 20UNC screws , washers , and nuts

to secure the carriage in place.

Step 3

The next steps are for those who are going to use either the near

ﬂush pipe or 1.5” NPT pipe for installation of the mount. Those

who wish to use the mast provided with the mount proceed to step

7. Mark and cut a 2.25” hole where you desire the near ﬂush pipe

or 1.5” NPT pipe to come down. Insert the near ﬂush pipe or

1.5” NPT pipe through the ceiling tile and into the carriage . Use

a brake screw in the bottom threaded hole of the carriage to

secure the near ﬂush pipe or 1.5” NPT pipe.

Step 4

Attach the desired mount to the female pipe couple , , and

. For the LCD-2537C, PM-1, PM-2, PM-3, or PM-3B this is done

with parts , , , and . Note: The mount shown in the

instructions is the PM-1. For the LCD-1C, LCD-1C w/ LCD-CM2, VMP-

042/044, or VMP046/048 this is done with parts to . Note:

The plastic washer goes on top of the desired mount as well as

inside the bottom of the female pipe couple .

Step 2: Attaching the carriage to

the ceiling plate

Step 3: Attaching the near

ﬂush pipe or 1.5” NPT pipe to

the carriage

Step 4: Attaching the female pipe

couple to the mount

VIDEO MOUNT PRODUCTS

21 22

19 20

23 24

25 29

Step 5

Insert the turnbuckles into the ceiling plate . Make sure to use

the sets of four holes in each corner of the ceiling plate and not the

center hole on each side. If necessary use the wood screw eyebolt

or concrete anchor to provide tie wire anchor points. To

use the tie wire cut the provided wire into four equal pieces.

Then insert one piece through each turnbuckle and twist the wire at

least four times itself. Attach the other end of each piece of wire to

the eyebolts, concrete anchors, or ceiling truss again making sure

the wire is twisted around itself at least four times. Note: If the dis-

tance between the ceiling grid and wherever you’re attaching the

tie wires is longer than 3 feet then you will require more tie wire (12

gauge steel tie wire).

Step 6

Attach the escutcheon ring to the near ﬂush pipe or 1.5”

NPT pipe. Attach the female pipe couple , , and to the

near ﬂush pipe or 1.5” NPT pipe. Use the ¼” – 20UNC brake screw

to secure the top of the couple from turning on the near

ﬂush pipe or 1.5” NPT pipe.

Please verify that all nuts and screws are tight.

Step 7

Attach the top of the ceiling mast (usually called the ceiling plate

in the instructions) to the adaptor plate . For the masts with a

cable channel make sure to nest the cable channel in the depres-

sion cut out in the adaptor plate. Secure the two together with 3/8”

– 16UNC screw , washers , and hex nuts .

Step 6: Attaching the female

pipe couple to the near ﬂush

pipe or 1.5” NPT pipe

Step 7: Attaching the upper mast

to the adaptor plate

Step 5: Supporting the ceiling plate

with tie wire

13 1

16 21 10

Step 8

Placetheescutcheonringadaptor ontopoftheceilingtileand

trace around the outside of the adaptor. Then proceed to cut just

inside the circle drawn. Insert the adaptor into the hole making sure

you have a tight ﬁt, and the wider top is on top of the ceiling tile. If

necessary widen the hole slightly to ﬁt in the adaptor. Insert the top

of the ceiling mast through the hole in the ceiling tile. Attach the

adaptor plate to the carriage and use the ¼” – 20UNC brake

screw to secure the adaptor plate from turning.

Step 9

Insert the turnbuckles into the ceiling plate . Make sure to use

the sets of four holes in each corner of the ceiling plate and not the

center hole on each side. If necessary use the wood screw eyebolt

or concrete anchor to provide tie wire anchor points. To

use the tie wire cut the provided wire into four equal pieces.

Then insert one piece through each turnbuckle and twist the wire at

least four times itself. Attach the other end of each piece of wire to

the eyebolts, concrete anchors, or ceiling truss again making sure

the wire is twisted around itself at least four times. The ceiling plate

should be completely supported by the tie wires. Note: If the dis-

tance between the ceiling grid and wherever you’re attaching the

tie wires is longer than 3 feet then you will require more tie wire (12

gauge steel tie wire).

Step 10

Attach the lower mast and rest of the mount to the upper mast us-

ing the appropriate through bolt and nut for that mount. Attach

the escutcheon ring onto the escutcheon ring adaptor .

Please verify that all nuts and screws are securely tightened.

VIDEO MOUNT PRODUCTS

WARNING: The installer of these products must verify that the mount-

ing surface, ceiling or wall, will safely support the combined weight

of all attached equipment and hardware. Video Mount Products will

not be held liable for the improper use or installation of its products.

Enjoy Your Mount!

14 17

Step 10: Attaching the lower half of

the mount to the upper mast

Step 8: Attach the adaptor plate

to the carriage

Step 9: Supporting the ceiling

plate with tie wire

Andere CablesPlus Rack & Stand Handbücher

CablesPlus

CablesPlus VH-001 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung